Helmut Raiger [Wed, 19 Oct 2011 20:34:43 +0000 (20:34 +0000)]
misc: pmic: fix regression in pmic_fsl.c (SPI)
This fixes write access to PMIC registers, the bug was
introduced partly in commit 64aac65099 and in commit c9fe76dd91.
It was tested on an i.mx31 with a mc13783.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
Simon Glass [Tue, 25 Oct 2011 11:29:28 +0000 (11:29 +0000)]
sandbox: Adjust Makefile so that standalone/api are not built
The check for sandbox architecture is too early in the Makefile, so
standalone and api are built regardless. This moves the check until
after autoconf.mk has been read.
Anton staaf [Tue, 25 Oct 2011 10:48:03 +0000 (10:48 +0000)]
sandbox: Add asm/cache.h for sandbox
This file is required by the new DMA buffer alignment macro.
Signed-off-by: Anton Staaf <robotboy@chromium.org> Cc: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Tue, 1 Nov 2011 20:54:02 +0000 (20:54 +0000)]
Reduce build times
U-Boot Makefiles contain a number of tests for compiler features etc.
which so far are executed again and again. On some architectures
(especially ARM) this results in a large number of calls to gcc.
This patch makes sure to run such tests only once, thus largely
reducing the number of "execve" system calls.
Example: number of "execve" system calls for building the "P2020DS"
(Power Architecture) and "qong" (ARM) boards, measured as:
-> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board>
-> grep execve /tmp/foo | wc -l
Wolfgang Denk [Sat, 29 Oct 2011 09:41:40 +0000 (09:41 +0000)]
common/cmd_ide.c: CodingStyle cleanup
Make file acceptable to checkpatch.
This is only a basic clean up to the extend possible without any real
changes to the source code. Warnings due to line over 80 characters
were accepted because these affect only printf()s with user visible
strings. No attempts were made to fix warnings about volatile and
externs - these need a more thorough cleanup.
Fix:
mv_eth.c: In function 'mv64460_eth_real_open':
mv_eth.c:471:6: warning: variable 'port_status' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_stop':
mv_eth.c:722:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_xmit':
mv_eth.c:796:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_receive':
mv_eth.c:877:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_get_stats':
mv_eth.c:979:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_update_stat':
mv_eth.c:1006:24: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c:1005:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_print_stat':
mv_eth.c:1087:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'eth_clear_mib_counters':
mv_eth.c:2141:15: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
Wolfgang Denk [Sat, 29 Oct 2011 09:37:34 +0000 (09:37 +0000)]
drivers/net/ns8382x.c: fix GCC 4.6 build warnings
Fix:
ns8382x.c: In function 'ns8382x_check_duplex':
ns8382x.c:704:6: warning: variable 'hun' set but not used
[-Wunused-but-set-variable]
To fix this, we get rid of the NS8382X_DEBUG code and use standard
debug() instead.
This will now trigger a so far undetected warning:
ns8382x.c:780:2: warning: format '%X' expects argument of type
'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Wolfgang Denk [Thu, 3 Nov 2011 19:36:16 +0000 (20:36 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
* 'master' of git://git.denx.de/u-boot-mmc:
tegra2: Move MMC clock initialization into MMC driver
mmc: sdhci: fix sdma bug for large file transfer
mmc: sdhci: add timeout for data transfer
mmc: sdhci: add mmc structure for host
mmc: sdhci: fix build warning
mmc: sdhci: fix cache flush
mmc: CMD7:MMC_CMD_SELECT_CARD response fix
mmc: test mmc bus width on startup
mmc: change magic number to macro define
mmc: mv_sdhci: fix 8bus width access for 88SV331xV5
mmc: retry the cmd8 to meet 74 clocks requirement in the spec
PXA: Add MMC driver using the generic MMC framework
Wolfgang Denk [Thu, 3 Nov 2011 19:36:04 +0000 (20:36 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-x86
* 'master' of git://git.denx.de/u-boot-x86:
x86: Fix a compiler warning in arch/x86/lib/realmode.c
x86: Remove the prototype for the unused function board_init
x86: Rename include/asm/ic to include/asm/arch-sc520
x86: turn off cache: set control register properly
Wolfgang Denk [Thu, 3 Nov 2011 19:35:45 +0000 (20:35 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-nds32
* 'master' of git://git.denx.de/u-boot-nds32:
nds32: asm/io.h: add __iormb __iowmb and inline io support
nds32: cache: define ARCH_DMA_MINALIGN for DMA buffer alignment
nds32: Use getenv_ulong() in place of getenv(), strtoul
Wolfgang Denk [Fri, 28 Oct 2011 05:37:04 +0000 (07:37 +0200)]
e1000: fix bugs from recent commits
Commit 114d7fc0 "e1000: Rewrite EEPROM checksum error to give more
information" failed to initialize the checksum variable which should
result in random results. Fix that.
Commit 2326a94d caused a ton of "unused variable 'x'" warnings.
Fix these. While we are at it, remove some bogus parens.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Stephen Warren [Mon, 31 Oct 2011 06:51:34 +0000 (06:51 +0000)]
tegra2: Move MMC clock initialization into MMC driver
This centralizes knowledge of MMC clocking into the MMC driver. This also
removes clock setup from the board files, which will simplify later changes
that modify the Harmony board to support the correct set of MMC controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Cc: Andy Fleming <afleming@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Lei Wen [Sat, 8 Oct 2011 04:14:58 +0000 (04:14 +0000)]
mmc: sdhci: fix sdma bug for large file transfer
SDHCI spec need to reset the sdma base address while the software
try to accorss the 512k bytes address boundary. When meet such
accross behavior, sdhci controller would generate a interrupt
automatically, and software need handle this.
Lei Wen [Sat, 8 Oct 2011 04:14:55 +0000 (04:14 +0000)]
mmc: sdhci: fix build warning
If CONFIG_MMC_SDHCI_IO_ACCESSORS is defined, the following warning would
shows up:
include/sdhci.h:224: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:224: warning: its scope is only this definition or
declaration, which is probably not what you want
include/sdhci.h:225: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:226: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:227: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:228: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:229: warning: 'struct sdhci_host' declared inside
parameter list
Ajay Bhargav [Wed, 5 Oct 2011 03:13:23 +0000 (03:13 +0000)]
mmc: CMD7:MMC_CMD_SELECT_CARD response fix
As per JEDEC document JESD84-A441 (page 105) response for CMD7
(MMC_CMD_SELECT_CARD) response should be R1 instead of R1b. In uboot we
never take MMC to disconnected state and on powerup its always ideal
state which later goes to stand-by state.
from document footnote:
R1 while selecting from Stand-By State to Transfer State; R1b while
selecting from Disconnected State to Programming State.
Lei Wen [Mon, 3 Oct 2011 20:33:44 +0000 (20:33 +0000)]
mmc: mv_sdhci: fix 8bus width access for 88SV331xV5
Marvell 88SV331xV5 platform's sdhci host control is not very standard
with the spec in the 8bit handling. It need to set its private register
to switch to the 8bit mode which is not included in the standard sdhci
registers.
This patch mainly hacks the writeb method, and set its private register
if it find the driver is going to switch to the 8bit mode.
Lei Wen [Fri, 2 Sep 2011 17:34:17 +0000 (17:34 +0000)]
mmc: retry the cmd8 to meet 74 clocks requirement in the spec
For some controller it has dynamic clock gating, and only toggle out clk
when the first cmd0 send out, while some card strictly obey the 74
clocks rule, the interval may not be sufficient between the cmd0 and
this cmd8, retry to fulfil the clock requirement.
Signed-off-by: Lei Wen <leiwen@marvell.com> Tested-by: Marek Vasut <marek.vasut@gmail.com>
Macpaul Lin [Mon, 24 Oct 2011 05:31:05 +0000 (13:31 +0800)]
nds32: asm/io.h: add __iormb __iowmb and inline io support
1. This patch add required __iormb and __iowmb to io.h.
This also fix some misbehavior to periphal drivers.
This io.h has been fixed with referencing arm/include/asm/io.h.
2. This patch replaced macro writeb and readb into inline function.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Kyle Moffett [Tue, 18 Oct 2011 11:05:29 +0000 (11:05 +0000)]
e1000: Allow direct access to the E1000 SPI EEPROM device
As a part of the manufacturing process for some of our custom hardware,
we are programming the EEPROMs attached to our Intel 82571EB controllers
from software using U-Boot and Linux.
This code provides several conditionally-compiled features to assist in
our manufacturing process:
CONFIG_CMD_E1000:
This is a basic "e1000" command which allows querying the controller
and (if other config options are set) performing EEPROM programming.
In particular, with CONFIG_E1000_SPI this allows you to display a
hex-dump of the EEPROM, copy to/from main memory, and verify/update
the software checksum.
CONFIG_E1000_SPI_GENERIC:
Build a generic SPI driver providing the standard U-Boot SPI driver
interface. This allows commands such as "sspi" to access the bus
attached to the E1000 controller. Additionally, some E1000 chipsets
can support user data in a reserved space in the E1000 EEPROM which
could be used for U-Boot environment storage.
CONFIG_E1000_SPI:
The core SPI access code used by the above interfaces.
For example, the following commands allow you to program the EEPROM from
a USB device (assumes CONFIG_E1000_SPI and CONFIG_CMD_E1000 are enabled):
usb start
fatload usb 0 $loadaddr 82571EB_No_Mgmt_Discrete-LOM.bin
e1000 0 spi program $loadaddr 0 1024
e1000 0 spi checksum update
Please keep in mind that the Intel-provided .eep files are organized as
16-bit words. When converting them to binary form for programming you
must byteswap each 16-bit word so that it is in little-endian form.
This means that when reading and writing words to the SPI EEPROM, the
bit ordering for each word looks like this on the wire:
Time >>>
------------------------------------------------------------------
... [7, 6, 5, 4, 3, 2, 1, 0, 15, 14, 13, 12, 11, 10, 9, 8], ...
------------------------------------------------------------------
(MSB is 15, LSB is 0).
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Ben Warren <biggerbadderben@gmail.com>
Kyle Moffett [Tue, 18 Oct 2011 11:05:28 +0000 (11:05 +0000)]
e1000: Export core EEPROM access functions for SPI support
A followup patch will be adding a configurable feature to enable
programming of E1000 EEPROMs from the command line or via the generic
U-Boot SPI interface.
In order for it to work it needs access to certain E1000-internal
functions, so export those in the e1000.h header file.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Ben Warren <biggerbadderben@gmail.com>
Kyle Moffett [Tue, 18 Oct 2011 11:05:26 +0000 (11:05 +0000)]
e1000: Restructure and streamline PCI device probing
By allocating the e1000 device structures much earlier, we can easily
generate better error messages and siginficantly clean things up.
The only user-visable change (aside from reworded error messages) is
that a detected e1000 device which fails to initialize due to software
or hardware error will still be allocated a device number.
As one example, consider a system with 2 e1000 PCI devices where the
first controller has a corrupted EEPROM. Using the old code the
second controller would be "e1000#0", while with this change it would be
"e1000#1".
This change should hopefully make such EEPROM errors much more
straightforward to handle correctly in boot scripts and the like.
It is also necessary for a followup patch which allows SPI programming
of an e1000 controller's EEPROM even if the checksum is invalid.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Ben Warren <biggerbadderben@gmail.com>
Wolfgang Denk [Thu, 27 Oct 2011 22:15:19 +0000 (00:15 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
Marek Vasut [Mon, 24 Oct 2011 23:41:42 +0000 (23:41 +0000)]
DEBUG: Fix debug macros
The current implementation of debug doesn't play well with GCC4.6.
This implementation also fixes GCC4.6 complaints about unused variables
while maintaining code size.
Also, drop the debugX() as that's not used anywhere anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 24 Oct 2011 23:41:41 +0000 (23:41 +0000)]
GCC4.6: Remove debugX() usage from spc1920 hpi
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:41:40 +0000 (23:41 +0000)]
GCC4.6: Squash warnings in omap4 clocks.c
clocks.c:606:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'u32 * const'
clocks.c:633:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'u32 * const'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:41:39 +0000 (23:41 +0000)]
GCC4.6: Squash warning in tegra2 board.c
board.c:43:2: warning: format '%08lX' expects type 'long unsigned int', but
argument 2 has type 'u32'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:41:38 +0000 (23:41 +0000)]
GCC4.6: Squash warnings in yaffs_guts.c
yaffs_guts.c: In function 'yaffs_ReadDataFromFile':
yaffs_guts.c:4461:8: warning: 'chunk' may be used uninitialized in this function
yaffs_guts.c:4462:8: warning: 'start' may be used uninitialized in this function
yaffs_guts.c: In function 'yaffs_WriteDataToFile':
yaffs_guts.c:4581:8: warning: 'chunk' may be used uninitialized in this function
yaffs_guts.c:4582:8: warning: 'start' may be used uninitialized in this function
yaffs_guts.c: In function 'yaffs_ResizeFile':
yaffs_guts.c:4816:8: warning: 'newSizeOfPartialChunk' may be used uninitialized
in this function
yaffs_guts.c:4817:8: warning: 'newFullChunks' may be used uninitialized in this
function
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org> Cc: William Juul <william.juul@tandberg.com>
Marek Vasut [Mon, 24 Oct 2011 23:41:37 +0000 (23:41 +0000)]
GCC4.6: Drop dead code from yaffs_guts.c
Drop yaffs_DeleteWorker():
yaffs_guts.c:1556:12: warning: 'yaffs_DeleteWorker' defined but not used
Drop yaffs_VerifyTnodeWorker():
yaffs_guts.c:600:12: warning: 'yaffs_VerifyTnodeWorker' defined but not used
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:41:36 +0000 (23:41 +0000)]
GCC4.6: Squash warnings in LzmaTools.c
LzmaTools.c: In function 'lzmaBuffToBuffDecompress':
LzmaTools.c:70:5: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'unsigned char *'
LzmaTools.c:71:5: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'unsigned char *'
LzmaTools.c:72:5: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'unsigned char *'
LzmaTools.c:73:5: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'unsigned char *'
LzmaTools.c:74:5: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'unsigned char *'
LzmaTools.c:110:5: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'SizeT'
LzmaTools.c:111:5: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'SizeT'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:41:00 +0000 (23:41 +0000)]
GCC4.6: Squash warning in lcd.c
lcd.c: In function 'lcd_setmem':
lcd.c:446:2: warning: format '%d' expects type 'int', but argument 2 has type
'u_long'
lcd.c:446:2: warning: format '%d' expects type 'int', but argument 3 has type
'u_long'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Fri, 21 Oct 2011 14:17:33 +0000 (14:17 +0000)]
GCC4.6: Squash GTREADREG related errors
interrupts.c: In function 'interrupt_init_cpu':
interrupts.c:37: warning: implicit declaration of function 'GTREGREAD'
interrupts.c:37: error: 'LOW_INTERRUPT_CAUSE_REGISTER' undeclared (first use in
this function)
interrupts.c:37: error: (Each undeclared identifier is reported only once
interrupts.c:37: error: for each function it appears in.)
interrupts.c:37: error: 'HIGH_INTERRUPT_CAUSE_REGISTER' undeclared (first use in
this function)
interrupts.c:40: error: 'ETHERNET0_INTERRUPT_CAUSE_REGISTER' undeclared (first
use in this function)
interrupts.c:40: error: 'ETHERNET1_INTERRUPT_CAUSE_REGISTER' undeclared (first
use in this function)
interrupts.c:40: error: 'ETHERNET2_INTERRUPT_CAUSE_REGISTER' undeclared (first
use in this function)
interrupts.c:44: error: 'ETHERNET0_INTERRUPT_MASK_REGISTER' undeclared (first
use in this function)
interrupts.c:44: error: 'ETHERNET1_INTERRUPT_MASK_REGISTER' undeclared (first
use in this function)
interrupts.c:44: error: 'ETHERNET2_INTERRUPT_MASK_REGISTER' undeclared (first
use in this function)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Tue, 25 Oct 2011 09:40:57 +0000 (11:40 +0200)]
GCC4.6: Squash warning in cmd_date.c
cmd_date.c: In function ‘do_date’:
cmd_date.c:50:6: warning: variable ‘old_bus’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:40:04 +0000 (23:40 +0000)]
GCC4.6: Use debug() instead of debugX() in s3c24xx_nand.c
The debugX() macro was always used with debug level 1. There is no point to use
it here instead of debug().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:40:03 +0000 (23:40 +0000)]
GCC4.6: Squash warnings in fec_mxc.c
fec_mxc.c: In function 'fec_mii_setspeed':
fec_mxc.c:112:2: warning: format '%#lx' expects type 'long unsigned int', but
argument 2 has type 'u32'
fec_mxc.c: In function 'fec_recv':
fec_mxc.c:632:2: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:40:02 +0000 (23:40 +0000)]
GCC4.6: Squash warning in bus_vcxk.c
bus_vcxk.c:167:2: warning: format '%d' expects type 'int', but argument 2 has
type 'u_long'
bus_vcxk.c:167:2: warning: format '%d' expects type 'int', but argument 3 has
type 'u_long'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:40:01 +0000 (23:40 +0000)]
GCC4.6: Squash warnings in ks8695eth.c
ks8695eth.c:199:2: warning: format '%x' expects type 'unsigned int', but
argument 4 has type 'volatile void *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:40:00 +0000 (23:40 +0000)]
GCC4.6: Squash warnings in lattice.c
lattice.c:319:4: warning: format '%x' expects type 'unsigned int', but argument
3 has type 'const char *'
lattice.c:319:4: warning: format '%x' expects type 'unsigned int', but argument
4 has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:39:59 +0000 (23:39 +0000)]
GCC4.6: Squash warnings in kirkwood_spi.c
kirkwood_spi.c:125:2: warning: format '%08X' expects type 'unsigned int', but
argument 4 has type 'const void *'
kirkwood_spi.c:125:2: warning: format '%08X' expects type 'unsigned int', but
argument 5 has type 'void *'
kirkwood_spi.c:160:5: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'void *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:39:58 +0000 (23:39 +0000)]
GCC4.6: Squash warnings in smsc95xx.c
smsc95xx.c: In function 'smsc95xx_write_hwaddr':
smsc95xx.c:380:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 24 Oct 2011 23:39:57 +0000 (23:39 +0000)]
GCC4.6: Fix warnings in pxa_mmc.c
pxa_mmc.c: In function 'mmc_cmd':
pxa_mmc.c:77:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'ulong'
pxa_mmc.c: In function 'mmc_block_read':
pxa_mmc.c:110:2: warning: format '%d' expects type 'int', but argument 4 has
type 'ulong'
pxa_mmc.c: In function 'pxa_mmc_write':
pxa_mmc.c:327:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:349:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:354:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:362:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:367:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>