]> git.sur5r.net Git - u-boot/log
u-boot
7 years agoSTiH410: Add STi pinctrl driver
Patrice Chotard [Tue, 21 Feb 2017 12:37:10 +0000 (13:37 +0100)]
STiH410: Add STi pinctrl driver

Add STMicroelectronics STiH410 pinctrl driver

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
7 years agoSTiH410: Add STi SDHCI driver
Patrice Chotard [Tue, 21 Feb 2017 12:37:09 +0000 (13:37 +0100)]
STiH410: Add STi SDHCI driver

Add SDHCI host controller found on STMicroelectronics SoCs

On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.

This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.

W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
7 years agogpio: do not include <asm/arch/gpio.h> for ARCH_STI
Patrice Chotard [Tue, 21 Feb 2017 12:37:08 +0000 (13:37 +0100)]
gpio: do not include <asm/arch/gpio.h> for ARCH_STI

As no gpio.h is defined in arch/arm/include/asm/arch-stih410,
to avoid compilation failure, do not include asm/arch/gpio.h.

This is needed for example when including sdhci.h, which include
asm/gpio.h>.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
7 years agoSTiH410: Add STi serial driver
Patrice Chotard [Tue, 21 Feb 2017 12:37:07 +0000 (13:37 +0100)]
STiH410: Add STi serial driver

This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
7 years agoSTiH410: Add STi sysreset driver
Patrice Chotard [Tue, 21 Feb 2017 12:37:06 +0000 (13:37 +0100)]
STiH410: Add STi sysreset driver

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
7 years agoSTiH410: Add STi timer driver
Patrice Chotard [Tue, 21 Feb 2017 12:37:05 +0000 (13:37 +0100)]
STiH410: Add STi timer driver

Add ARM global timer based timer

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
7 years agoarm: Add support for STMicroelectronics STiH410 soc
Patrice Chotard [Tue, 21 Feb 2017 12:37:04 +0000 (13:37 +0100)]
arm: Add support for STMicroelectronics STiH410 soc

The STiH410 is an advanced multi-HD AVC processor with 3D
graphics acceleration and 1.5-GHz ARM Cortex-A9 SMP CPU
part of the STiH407 family.

It has wide connectivity including USB 3.0, PCI-e, SATA
and gigabit ethernet.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
7 years agoarmv7m: Add SysTick timer driver
Phil Edworthy [Fri, 17 Feb 2017 08:22:17 +0000 (08:22 +0000)]
armv7m: Add SysTick timer driver

The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.

The number of reference clock ticks that correspond to 10ms is normally
defined in the SysTick Calibration register's TENMS field. However, on some
devices this is wrong, so this driver allows the clock rate to be defined
using CONFIG_SYS_HZ_CLOCK.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
7 years agotools: omapimage: Fix size in header
Lokesh Vutla [Wed, 15 Feb 2017 13:12:54 +0000 (18:42 +0530)]
tools: omapimage: Fix size in header

The size field in GP header that is expected by ROM is size of the
image + size of the header. But omapimage generates a gp header
only with size of the image as size field. Fix it

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
7 years agoarm: omap3: Bring back ARM errata workaround 725233
Siarhei Siamashka [Mon, 6 Mar 2017 01:16:53 +0000 (03:16 +0200)]
arm: omap3: Bring back ARM errata workaround 725233

The workaround for ARM errata 725233 had been lost since
commit 45bf05854bc94e (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoarm: omap3: Compile clock.c with -marm option to unbreak OMAP3530
Siarhei Siamashka [Mon, 6 Mar 2017 01:16:52 +0000 (03:16 +0200)]
arm: omap3: Compile clock.c with -marm option to unbreak OMAP3530

Boards with OMAP3530 SoC fail to boot since commit bd2c4522c26d5
("ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)")
because it enabled the use of Thumb2 for the SPL.

Experiments have shown that the deadlock happens in the
prcm_init() function from 'arch/arm/mach-omap2/omap3/clock.c'.

This patch enforces the compilation of clock.c source file in
ARM mode and makes the deadlock disappear. We are yet to figure
out the root cause of the problem. Still this is somewhat
better than having non-bootable boards for years.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
7 years agoomap3_overo: Reduce SPL size
Tom Rini [Fri, 10 Mar 2017 19:16:54 +0000 (14:16 -0500)]
omap3_overo: Reduce SPL size

Borrowing from omap3_logic, switch to SPL_SYS_MALLOC_SIMPLE and moving
the stack to DDR as soon as we're able.

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoARM: dts: uniphier: more re-sync DT with Linux
Masahiro Yamada [Sun, 12 Mar 2017 15:16:41 +0000 (00:16 +0900)]
ARM: dts: uniphier: more re-sync DT with Linux

For better maintainability.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: dts: uniphier: fix no unit name warnings
Masahiro Yamada [Sun, 12 Mar 2017 15:16:40 +0000 (00:16 +0900)]
ARM: dts: uniphier: fix no unit name warnings

Fix warnings reported when built with W=1, by DTC 1.4.2 or later:
  Node /memory has a reg or ranges property, but no unit name

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: dts: uniphier: remove skeleton.dtsi inclusion
Masahiro Yamada [Sun, 12 Mar 2017 15:16:39 +0000 (00:16 +0900)]
ARM: dts: uniphier: remove skeleton.dtsi inclusion

Linux Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated") declared that skeleton.dtsi was deprecated.

Move the memory node below to suppress warnings of FDTGREP.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: set DRAM_SPARSE flag for LD21 boards
Masahiro Yamada [Mon, 6 Mar 2017 20:28:25 +0000 (05:28 +0900)]
ARM: uniphier: set DRAM_SPARSE flag for LD21 boards

Commit 04cd4e7215d3 ("ARM: uniphier: remove DRAM base address from
board parameters") accidentally unset the DRAM_SPARSE flag, and
changed the physical map of the DRAM channels.  Revive the original
behavior.

Fixes: 04cd4e7215d3 ("ARM: uniphier: remove DRAM base address from board parameters")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Shunji Sato <sato.shunji@socionext.com>
7 years agoPrepare v2017.03 v2017.03
Tom Rini [Mon, 13 Mar 2017 17:54:16 +0000 (13:54 -0400)]
Prepare v2017.03

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoscripts/config_whitelist.txt: Regenerate
Tom Rini [Mon, 13 Mar 2017 17:50:17 +0000 (13:50 -0400)]
scripts/config_whitelist.txt: Regenerate

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoconfigs: Re-sync
Tom Rini [Mon, 13 Mar 2017 17:48:42 +0000 (13:48 -0400)]
configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoarm: omap-common: Fix typo in CONFIG_OMAP54XX guard
Matthijs van Duin [Tue, 7 Mar 2017 02:42:24 +0000 (03:42 +0100)]
arm: omap-common: Fix typo in CONFIG_OMAP54XX guard

Some initialization was unintentionally being skipped on omap5.

Fixes: f5af0827f276 ("arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX")
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
7 years agotools: binman: change shebang from python into python2
Jörg Krause [Mon, 6 Mar 2017 20:07:11 +0000 (21:07 +0100)]
tools: binman: change shebang from python into python2

This tool does not work with Python 3. Change the shebang to make sure the
script is run by a Python 2 interpreter.

Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
7 years agoarm: OMAP2+: nandecc: propagate error to command return status
Ladislav Michl [Mon, 6 Mar 2017 12:54:30 +0000 (13:54 +0100)]
arm: OMAP2+: nandecc: propagate error to command return status

Currently nandecc returns zero even if underlaying
omap_nand_switch_ecc function fails. Fix that by
propagating error returned to command return value.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
7 years agoMerge branch 'pmic' of git://git.denx.de/u-boot-mmc
Tom Rini [Fri, 10 Mar 2017 00:52:57 +0000 (19:52 -0500)]
Merge branch 'pmic' of git://git.denx.de/u-boot-mmc

7 years agoARM: Migrate errata to Kconfig
Tom Rini [Tue, 7 Mar 2017 12:13:42 +0000 (07:13 -0500)]
ARM: Migrate errata to Kconfig

This moves all of the current ARM errata from various header files and in to
Kconfig.  This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config.  We now just select these once at the higher level in Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoomap4: Migrate to using imply
Tom Rini [Fri, 3 Mar 2017 20:33:33 +0000 (15:33 -0500)]
omap4: Migrate to using imply

Move the default y options under arch/arm/mach-omap2/omap4/Kconfig to be
using imply instead in arch/arm/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoomap3: Migrate to using imply
Tom Rini [Fri, 3 Mar 2017 20:33:32 +0000 (15:33 -0500)]
omap3: Migrate to using imply

Move the default y options under arch/arm/mach-omap2/omap3/Kconfig to be
using imply instead in arch/arm/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoTI: Migrate board/ti/common/Kconfig to imply
Tom Rini [Fri, 3 Mar 2017 20:33:31 +0000 (15:33 -0500)]
TI: Migrate board/ti/common/Kconfig to imply

The option that we had set in board/ti/common/Kconfig as default y are
best done with imply under the appropriate main Kconfig option instead.

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoam335x_evm: Switch to using imply keyword
Tom Rini [Fri, 3 Mar 2017 20:33:30 +0000 (15:33 -0500)]
am335x_evm: Switch to using imply keyword

These particular SPL options are part of what the ROM provides, but for
compatibility with how we have previously used them, move them to being
implied by the board being selected.

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agokconfiglib.py: Kludge in 'imply' support
Tom Rini [Fri, 3 Mar 2017 20:33:29 +0000 (15:33 -0500)]
kconfiglib.py: Kludge in 'imply' support

Currently upstream does not yet understand the imply keyword.  For what
we use kconfiglib.py for today, this is OK.  We only need to be able to
evaluate in order to make boards.cfg and none of those choices will
depend on how imply evaluates out.

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agodo_smhload: fix return code
Ryan Harkin [Thu, 2 Mar 2017 17:45:16 +0000 (17:45 +0000)]
do_smhload: fix return code

do_smhload was using a ulong to store the return value from
smh_load_file. That returns an int, where -1 indicates an error. As a
ulong will never be negative, smh_load_file errors were not detected and
so_smhload always returned zero.

Also, when errors were spotted, do_smhload was returning 1, rather than
the enumeration CMD_RET_FAILURE (which is also 1).

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
7 years agoFreescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigs
Tom Rini [Wed, 1 Mar 2017 21:51:58 +0000 (16:51 -0500)]
Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigs

In some cases this is absolutely required, so select this for some secure
features.  This also requires migration of RSA_FREESCALE_EXP

Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agotools: Remove CONFIG_SYS_TEXT_BASE in Makefile
Patrick Delaunay [Tue, 28 Feb 2017 18:29:11 +0000 (19:29 +0100)]
tools: Remove CONFIG_SYS_TEXT_BASE in Makefile

This define is not used in tools sources and can be removed
to avoid unnecessary link between tools and defconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
7 years agokbuild: turn of dtc unit address warnings by default
Masahiro Yamada [Mon, 27 Feb 2017 06:24:45 +0000 (15:24 +0900)]
kbuild: turn of dtc unit address warnings by default

DTC 1.4.2 or later checks DT unit-address without reg property and
vice-versa, and generates lots of warnings.  Fixing DT files will
take for a while.  Until then, let's turn off the check unless
building with W=*.

Introduce a new helper dtc-option to check if the option is supported
in order to suppress warnings on older versions.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
7 years agosunxi: power: axp809.c: Fix aldo1-2 being disabled for mvolt != 0
Rask Ingemann Lambertsen [Wed, 18 Jan 2017 20:53:40 +0000 (21:53 +0100)]
sunxi: power: axp809.c: Fix aldo1-2 being disabled for mvolt != 0

The execution flow is currently like this for aldo_num == 1 or 2:

int axp_set_aldo(int aldo_num, unsigned int mvolt)
{
...
if (mvolt == 0)
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
...
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
  AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
 }

I.e. aldo1 and aldo2 will always be disabled. This patch fixes it by
setting (rather than clearing) the enable bit when mvolt != 0.

Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Fixes: 795857df413a ("sunxi: power: add AXP809 support")
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-video
Tom Rini [Wed, 8 Mar 2017 12:14:21 +0000 (07:14 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-video

7 years agoMerge branch 'master' of git://git.denx.de/u-boot-net
Tom Rini [Wed, 8 Mar 2017 12:14:18 +0000 (07:14 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-net

7 years agoomap3_logic: Move SPL Stack into SDRAM
Adam Ford [Wed, 8 Mar 2017 03:27:52 +0000 (21:27 -0600)]
omap3_logic: Move SPL Stack into SDRAM

A previous patch broke the board. This patch will add missing part
from the previous patch and also move the SPL Stack into SDRAM at
0x82000000.

Tested with GCC 4.8.2 and GCC 6.2

Fixes: 0959649dc6d9 ("omap3_logic: Switch to simple malloco in SPL")
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
  - Keep CONFIG_SPL_SYS_MALLOC_SIMPLE
  - Add CONFIG_SYS_MALLOC_F_LEN=0x2000 (8 MB)

7 years agovideo: cfb_console: fix 32-bit display on 64-bit architectures
Andre Przywara [Mon, 6 Mar 2017 01:13:38 +0000 (01:13 +0000)]
video: cfb_console: fix 32-bit display on 64-bit architectures

"unsigned long" is a lousy data type when it comes to match peripheral
hardware registers with a fixed size.
Just do the obvious and match a 32-bit display format with an "u32"
data type for casting.
This fixes the logo display on 64-bit architectures, which produced
a black line on the right side of the logo with non-black backgrounds.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
7 years agonet: zynq_gem: Fix masking of supported phydev features
Nathan Rossi [Sun, 5 Mar 2017 14:36:23 +0000 (00:36 +1000)]
net: zynq_gem: Fix masking of supported phydev features

When the zynq_gem driver initializes the phy it sets the supported
features that the phy can support and advertise. However instead of
masking the supported features such that it limits the available
features it sets the phy to have the exact supported features of the
zynq_gem. This is problematic as it will enable features that a phy does
not have or cannot advertise.

Specifically this appears as an issue when using a phy that is only
capable of 10/100, but the zynq_gem driver will override this and try to
enable and advertise 10/100/1000.

Reported-by: Arno Steffens <star@gmx.li>
Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Tested-by: Arno Steffens <star@gmx.li>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
7 years agonet: macb: Fix ETH not found when clock not support
Wenyou Yang [Tue, 14 Feb 2017 08:24:40 +0000 (16:24 +0800)]
net: macb: Fix ETH not found when clock not support

For the boards such as smartweb on which the clock driver isn't
supported, the ethernet fail to be found when booting up with
the below log.
---8<---
Net:   No ethernet found.
--->8---

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
7 years agoarmv8: spl: Call spl_relocate_stack_gd for ARMv8
Philipp Tomsich [Wed, 1 Mar 2017 20:04:15 +0000 (21:04 +0100)]
armv8: spl: Call spl_relocate_stack_gd for ARMv8

As part of the startup process for boards using the SPL, we need to
call spl_relocate_stack_gd. This is needed to set up malloc with its
DRAM buffer.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
7 years agoarmv5te: make 'ret lr' produce iinterworking 'bx lr'
Albert ARIBAUD [Mon, 27 Feb 2017 19:19:07 +0000 (20:19 +0100)]
armv5te: make 'ret lr' produce iinterworking 'bx lr'

Current ARM assembler helper for the 'return to caller' pseudo-instruction
turns 'ret lr' into 'mov pc, lr' for ARMv5TE. This causes the core to remain
in its current ARM state even when the routine doing the 'ret' was called
from Thumb-1 state, triggering an undefined instruction exception.

This causes early run-time failures in all boards compiled using the Thumb-1
instruction set (for instance the Open-RD family).

ARMv5TE supports 'bx lr' which properly implements interworking and thus
correctly returns to Thumb-1 state from ARM state.

This change makes 'ret lr' turn into 'bx lr' for ARMv5TE.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
7 years agoPrepare v2017-rc3 v2017.03-rc3
Tom Rini [Mon, 27 Feb 2017 22:36:21 +0000 (17:36 -0500)]
Prepare v2017-rc3

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoarm: mach-omap2: Flush cache after FIT post-processing image
Andrew F. Davis [Wed, 22 Feb 2017 23:46:39 +0000 (17:46 -0600)]
arm: mach-omap2: Flush cache after FIT post-processing image

After we authenticate/decrypt an image we need to flush the caches
as they may still contain bits of the encrypted image. This will
cause failures if we attempt to jump to this image.

Reported-by: Yogesh Siraswar<yogeshs@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
7 years agodrivers/net/Kconfig: Correct use of apostrophe
Tom Rini [Mon, 20 Feb 2017 14:38:03 +0000 (09:38 -0500)]
drivers/net/Kconfig: Correct use of apostrophe

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoMerge branch 'master' of git://www.denx.de/git/u-boot-imx
Tom Rini [Mon, 27 Feb 2017 17:10:05 +0000 (12:10 -0500)]
Merge branch 'master' of git://www.denx.de/git/u-boot-imx

7 years agorockchip: video: fix 83500000 clock mistake in rockchip HDMI
Nickey Yang Nickey Yang [Mon, 27 Feb 2017 09:04:21 +0000 (17:04 +0800)]
rockchip: video: fix 83500000 clock mistake in rockchip HDMI

There is one "0" too many in 83500000 mpixelclock in rockchip_mpll_cfg[].
fix it.

Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
7 years agosplash: Prevent splash_load_fs from writing to 0x0
Jonathan Golder [Fri, 24 Feb 2017 16:46:10 +0000 (17:46 +0100)]
splash: Prevent splash_load_fs from writing to 0x0

Passing NULL to fs_read() for actread value results in hanging U-Boot
at least on our ARM plattform (TI AM335x). Since fs_read() and
following functions do not catch nullpointers, writing to 0x0 occurs.

Passing a local dummy var instead of NULL solves this issue.

Signed-off-by: Jonathan Golder <jonathan.golder@kurz-elektronik.de>
Cc: Anatolij Gustschin <agust@denx.de>
7 years agotravis-ci: Temporarily disable using a newer device tree compiler
Tom Rini [Sun, 26 Feb 2017 20:23:18 +0000 (15:23 -0500)]
travis-ci: Temporarily disable using a newer device tree compiler

For a long while dtc has warned about various constructs.  This is now
leading to log file size being exceeded in travis, and as the majority
of these errors need to be fixed in the kernel, switch to using the
stock device-tree-compiler package.

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-usb
Tom Rini [Sun, 26 Feb 2017 16:56:54 +0000 (11:56 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-usb

7 years agousb: gadget: f_dfu: set serial number if serial# is valid
Felipe Balbi [Wed, 22 Feb 2017 09:22:38 +0000 (11:22 +0200)]
usb: gadget: f_dfu: set serial number if serial# is valid

With this patch, USB Command Verifier is happy with our DFU
implementation on Chapter 9 tests.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
7 years agousb: gadget: g_dnl: fix g_dnl_set_serialnumber()
Felipe Balbi [Wed, 22 Feb 2017 09:22:37 +0000 (11:22 +0200)]
usb: gadget: g_dnl: fix g_dnl_set_serialnumber()

instead of only copying if strlen(s) is less than 32 characters, let's
just copy at most 31 characters regardless of the size of
serial#. This will guarantee that we always have a serial number if
serial# environment variable is set to anything.

Note that without a proper serial number, USB Command Verifier fails
our test of Device Descriptor since we will claim to have a serial
number without really providing one when requested.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
7 years agousb: gadget: f_dfu: write req->actual bytes
Felipe Balbi [Fri, 10 Feb 2017 16:32:31 +0000 (19:32 +0300)]
usb: gadget: f_dfu: write req->actual bytes

If last packet is short, we shouldn't write req->length bytes to
non-volatile media, we should write only what's available to us, which
is held in req->actual.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
7 years agousb: gadget: dfu: add result for handle_getstatus()
Patrick Delaunay [Fri, 16 Dec 2016 17:41:32 +0000 (18:41 +0100)]
usb: gadget: dfu: add result for handle_getstatus()

harmonize result with other handle_XXX() functions: return int for size
remove the define RET_STAT_LEN : no more necessary

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
7 years agousb: gadget: dfu: correct size for USB_REQ_DFU_GETSTATE result
Patrick Delaunay [Fri, 16 Dec 2016 17:41:31 +0000 (18:41 +0100)]
usb: gadget: dfu: correct size for USB_REQ_DFU_GETSTATE result

return the correct size for DFU_GETSTATE result (1 byte in DFU 1.1 spec)
to avoid issue in USB protocol and the variable "value" is propagated
to req->lenght as all the in the other request with answer
- DFU_GETSTATUS
- DFU_DNLOAD
- DFU_UPLOAD
Then the buffer is correctly treated in USB driver

NB: it was the only request witch directly change "req->actual"

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
7 years agousb: gadget: dfu: add functional descriptor in descriptor set
Patrick Delaunay [Thu, 8 Dec 2016 17:10:49 +0000 (18:10 +0100)]
usb: gadget: dfu: add functional descriptor in descriptor set

The "DFU descriptor set" must contain the "DFU functional descriptor"
but it is missing today in U-Boot code
(cf: DFU spec 1.1, chapter 4.2 DFU Mode Descriptor Set)
This patch only allocate buffer and copy DFU functional descriptor
after interfaces.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
7 years agousb: dwc3: gadget: Remove unused header inclusion
Vincent Tinelli [Tue, 14 Feb 2017 14:16:25 +0000 (17:16 +0300)]
usb: dwc3: gadget: Remove unused header inclusion

Remove sys_proto.h inclusion which is not used by the driver.

Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-uniphier
Tom Rini [Thu, 23 Feb 2017 15:12:41 +0000 (10:12 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier

  - Fix regressions caused by the previous reworks
  - Add pin configuration support
  - Re-work SPL code
  - Update DRAM and PLL setup code
  - Enable needed configs, disable unneeded configs

7 years agoARM: uniphier: set up charge pump current for MPLL of LD11 SoC
Masahiro Yamada [Tue, 21 Feb 2017 14:00:35 +0000 (23:00 +0900)]
ARM: uniphier: set up charge pump current for MPLL of LD11 SoC

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: add simple eMMC load APIs instead of ROM API
Masahiro Yamada [Mon, 20 Feb 2017 09:34:20 +0000 (18:34 +0900)]
ARM: uniphier: add simple eMMC load APIs instead of ROM API

Re-use of routines embedded in the Boot ROM requires a function
pointer table for each SoC.  This is not nice in terms of the
maintainability in a long run.

Implement simple eMMC load APIs that are commonly used for LD11,
LD20, and hopefully future SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: enable CONFIG_CMD_CONFIG
Masahiro Yamada [Tue, 21 Feb 2017 06:09:11 +0000 (15:09 +0900)]
ARM: uniphier: enable CONFIG_CMD_CONFIG

This command is useful to see which config options are enabled on
the running U-Boot image.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: enable CONFIG_CMD_GPT
Masahiro Yamada [Fri, 17 Feb 2017 07:17:55 +0000 (16:17 +0900)]
ARM: uniphier: enable CONFIG_CMD_GPT

Enable CONFIG_CMD_GPT, keeping CONFIG_SPL_EFI_PARTITION because the
SPL for UniPhier platform does not recognize any partitions.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: disable CONFIG_SPL_DOS_PARTITION
Masahiro Yamada [Fri, 17 Feb 2017 07:17:39 +0000 (16:17 +0900)]
ARM: uniphier: disable CONFIG_SPL_DOS_PARTITION

The SPL for UniPhier platform does not recognize any partitions.
Do not compile unneeded features.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: deassert RST_n of eMMC device for LD11/LD20
Masahiro Yamada [Fri, 17 Feb 2017 07:17:22 +0000 (16:17 +0900)]
ARM: uniphier: deassert RST_n of eMMC device for LD11/LD20

For LD11 and LD20 SoCs, the RST_n pin is asserted by default.  If
the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device
would stay in the reset state until its RST_n pin is deasserted by
software.

Currently, this is cared by an ad-hoc way because the eMMC hardware
reset provider is not supported in U-Boot for now.  This code should
be re-written once the "mmc-pwrseq-emmc" binding is supported.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: add DRAM PHY clock duty adjustment for LD20 SoC
Kotaro Hayashi [Tue, 14 Feb 2017 02:39:14 +0000 (11:39 +0900)]
ARM: uniphier: add DRAM PHY clock duty adjustment for LD20 SoC

If the DRAM clock duty does not meet the allowable tolerance,
it is marked in an efuse register.  If the register is fused,
the boot code should compensate for the DRAM clock duty error.

Signed-off-by: Kotaro Hayashi <hayashi.kotaro@socionext.com>
[masahiro: simplify code, add git-log]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: remove dram_nr_ch from board parameters
Masahiro Yamada [Thu, 16 Feb 2017 06:59:32 +0000 (15:59 +0900)]
ARM: uniphier: remove dram_nr_ch from board parameters

This parameter is redundant because we can know the number of
channels by checking if dram_ch[2].size is zero.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: rework spl_boot_device() and related code
Masahiro Yamada [Mon, 13 Feb 2017 16:24:26 +0000 (01:24 +0900)]
ARM: uniphier: rework spl_boot_device() and related code

The current implementation has ugly switch statements here and there,
and duplicates similar code.  Rework it using table lookups for SoC
data and reduce code duplication.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: move spl_boot_mode() to a separate file
Masahiro Yamada [Mon, 13 Feb 2017 16:24:25 +0000 (01:24 +0900)]
ARM: uniphier: move spl_boot_mode() to a separate file

The spl_boot_mode() is unrelated to the other code in this file.
Besides, this function is only called from common/spl/spl_mmc.c,
so it is reasonable to guard with CONFIG_SPL_MMC_SUPPORT.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: move MMC code to a separate file
Masahiro Yamada [Mon, 13 Feb 2017 16:24:24 +0000 (01:24 +0900)]
ARM: uniphier: move MMC code to a separate file

Currently, arch/arm/mach-uniphier/boot-mode/boot-mode.c is messed up
with unrelated code; there is no reason why the "mmcsetn" command
must be placed in this file.

Split out the MMC code into arch/arm/mach-uniphier/mmc-first-dev.c.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: disable CONFIG_MTD_NOR_FLASH
Masahiro Yamada [Mon, 13 Feb 2017 01:29:55 +0000 (10:29 +0900)]
ARM: uniphier: disable CONFIG_MTD_NOR_FLASH

This feature is seldom used these days on UniPhier boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: dts: uniphier: drop u-boot, dm-pre-reloc from system-bus pinctrl node
Masahiro Yamada [Sun, 12 Feb 2017 14:44:57 +0000 (23:44 +0900)]
ARM: dts: uniphier: drop u-boot, dm-pre-reloc from system-bus pinctrl node

Since commit 26b09c022ab6 ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), SPL does not need pin-mux settings for
the System Bus.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: rename second stage loader name
Masahiro Yamada [Sun, 12 Feb 2017 09:21:16 +0000 (18:21 +0900)]
ARM: uniphier: rename second stage loader name

For the memory footprint reason, the Boot ROM can not load the ARM
Trusted Firmware BL1 directly when Trusted Board Boot is enabled.
The second stage loader is Socionext's own firmware, so rename it
for clarification.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agopinctrl: uniphier: support pin configuration
Masahiro Yamada [Sun, 12 Feb 2017 09:21:15 +0000 (18:21 +0900)]
pinctrl: uniphier: support pin configuration

Support the following DT properties:
  "bias-disable"
  "bias-pull-up"
  "bias-pull-down"
  "bias-pull-pin-default"
  "input-enable"
  "input-disable"

My main motivation is to support pull up/down biasing.  For Pro5 and
later SoCs, the pupdctrl register number is the same as the pinmux
number, so this feature can be supported without having big pin
tables.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: enable generic EHCI driver for uniphier_v8_defconfig
Masahiro Yamada [Tue, 7 Feb 2017 12:25:13 +0000 (21:25 +0900)]
ARM: uniphier: enable generic EHCI driver for uniphier_v8_defconfig

The LD11 SoC is equipped with USB EHCI controllers.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: remove DRAM base address from board parameters
Masahiro Yamada [Sun, 5 Feb 2017 01:52:12 +0000 (10:52 +0900)]
ARM: uniphier: remove DRAM base address from board parameters

The base address of each DRAM channel can be calculated from other
parameters, so does not need hard-coding.  What we need is the size
of each DRAM channel and DRAM_SPARSE flag to decide the start address
of DRAM channel 1.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: update README.uniphier for latest build instruction
Masahiro Yamada [Mon, 30 Jan 2017 04:12:28 +0000 (13:12 +0900)]
ARM: uniphier: update README.uniphier for latest build instruction

Since commit c0efc3140e75 ("ARM: uniphier: change CONFIG_SPL_PAD_TO
to 128KB"), the u-boot.bin should be burned at the offset 0x20000.
I missed to update README.uniphier in that commit.  Now updating.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: print Support Card info very late
Masahiro Yamada [Mon, 20 Feb 2017 08:32:19 +0000 (17:32 +0900)]
ARM: uniphier: print Support Card info very late

Since commit 26b09c022ab6 ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), the System Bus is initialized by
board_init().  The show_board_info() is called from board_init_f()
by default, so the revision register of the Micro Support Card may
not be accessed at this point.  Show its revision after the System
Bus is initialized.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: skip memreserve of unused DRAM bank of LD20
Masahiro Yamada [Mon, 20 Feb 2017 08:13:32 +0000 (17:13 +0900)]
ARM: uniphier: skip memreserve of unused DRAM bank of LD20

Now the "for" loop here iterates on the detected memory banks.
It must skip unused DRAM banks.

Fixes: c995f3a3c526 ("ARM: uniphier: use gd->bd->bi_dram for memory reserve on LD20 SoC")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: correct spelling of "invalid"
Masahiro Yamada [Mon, 20 Feb 2017 03:09:00 +0000 (12:09 +0900)]
ARM: uniphier: correct spelling of "invalid"

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: skip MEMCONF ch2 parsing if CH2_DISABLE bit is set
Masahiro Yamada [Mon, 20 Feb 2017 03:10:05 +0000 (12:10 +0900)]
ARM: uniphier: skip MEMCONF ch2 parsing if CH2_DISABLE bit is set

If SG_MEMCONF_CH2_DISABLE bit is set, the DRAM channel 2 is unused.
The register settings for the ch2 should be ignored.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agoARM: uniphier: revive accidentally removed dcache_disable()
Masahiro Yamada [Mon, 20 Feb 2017 05:23:37 +0000 (14:23 +0900)]
ARM: uniphier: revive accidentally removed dcache_disable()

Commit a8e6300d483d ("ARM: uniphier: refactor spl_init_board()")
accidentally dropped dcache_disable() call.  Since then, the SPL of
LD11 and LD20 failed to load U-Boot proper.

Fixes: a8e6300d483d ("ARM: uniphier: refactor spl_init_board()")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
7 years agovideo: mxsfb: Fix reset hang when videomode variable is not present
Fabio Estevam [Wed, 22 Feb 2017 13:40:22 +0000 (10:40 -0300)]
video: mxsfb: Fix reset hang when videomode variable is not present

Currently the system hangs when the 'videomode' variable is not present
and a reset command is issued:

=> setenv videomode
=> saveenv
=> reset

(Board hangs)

lcdif_power_down() assumes that the LCDIF controller has been properly
configured and enabled, which may not be true.

To fix this issue check whether panel.frameAdrs has been initialized and
in case it has not been initialized, do not continue with the LCDIF
powerdown sequence.

Tested on a imx7dsabresd board.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
7 years agoMerge git://git.denx.de/u-boot-x86
Tom Rini [Wed, 22 Feb 2017 15:27:37 +0000 (10:27 -0500)]
Merge git://git.denx.de/u-boot-x86

7 years agox86: Intel MID platforms has no microcode update
Andy Shevchenko [Fri, 17 Feb 2017 13:49:00 +0000 (16:49 +0300)]
x86: Intel MID platforms has no microcode update

There is no microcode update available for SoCs used on Intel MID
platforms.

Use conditional to bypass it.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
7 years agox86: zImage: add Intel MID platforms support
Vincent Tinelli [Fri, 17 Feb 2017 13:48:59 +0000 (16:48 +0300)]
x86: zImage: add Intel MID platforms support

Intel MID platform boards have special treatment, such as boot parameter
setting.

Assign hardware_subarch accordingly if CONFIG_INTEL_MID is set.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
7 years agox86: Introduce INTEL_MID quirk option
Andy Shevchenko [Fri, 17 Feb 2017 13:48:58 +0000 (16:48 +0300)]
x86: Introduce INTEL_MID quirk option

Intel Mobile Internet Device (MID) platforms have special treatment in
some cases, such as CPU enumeration or boot parameters configuration.

Besides that several drivers are specifically developed for the IP
blocks found on Intel MID platforms. Those drivers will be dependent to
this option.

Here we introduce specific quirk option for such cases.

It is supposed to be selected by Intel MID platform boards, for example,
Intel Edison.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
7 years agox86: Force 32-bit jumps in interrupt handlers
J. Tang [Fri, 10 Feb 2017 02:54:13 +0000 (21:54 -0500)]
x86: Force 32-bit jumps in interrupt handlers

Depending upon the compiler used, IRQ entries could vary in sizes. With
GCC 5.x, the code generator will use short jumps for some IRQ entries
but near jumps for others. For example, GCC 5.4.0 generates the
following:

$ objdump -d interrupt.o
<snip>
00000207 <irq_18>:
207:   6a 12                   push   $0x12
209:   eb 85                   jmp    190 <irq_common_entry>

0000020b <irq_19>:
20b:   6a 13                   push   $0x13
20d:   eb 81                   jmp    190 <irq_common_entry>

0000020f <irq_20>:
20f:   6a 14                   push   $0x14
211:   e9 7a ff ff ff          jmp    190 <irq_common_entry>

00000216 <irq_21>:
216:   6a 15                   push   $0x15
218:   e9 73 ff ff ff          jmp    190 <irq_common_entry>

This causes a problem in cpu_init_interrupts(), because the IDT setup
assumed same sizes for all IRQ entries. GCC 4.x always generated 32-bit
jumps, so this previously was not a problem.

The fix is to force 32-bit near jumps for all entries within the
inline assembly. This works for GCC 5.x, and 4.x was already using
that form of jumping.

Signed-off-by: Jason Tang <tang@jtang.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
7 years agotqma6: [cosmetic] sanitize environment defines
Markus Niebel [Fri, 3 Feb 2017 15:14:03 +0000 (16:14 +0100)]
tqma6: [cosmetic] sanitize environment defines

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
7 years agotqma6: fix rounding in env
Markus Niebel [Fri, 3 Feb 2017 15:14:02 +0000 (16:14 +0100)]
tqma6: fix rounding in env

need to add before div in mmc update scripts. Otherwise we could
write one block more ba acident

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
7 years agomx6: tqma6: add rootfsmode environment for mmc / sd
Markus Niebel [Fri, 3 Feb 2017 15:14:01 +0000 (16:14 +0100)]
mx6: tqma6: add rootfsmode environment for mmc / sd

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
7 years agomx6: tqma6: fix typo in env
Markus Niebel [Fri, 3 Feb 2017 15:14:00 +0000 (16:14 +0100)]
mx6: tqma6: fix typo in env

there was a double bracketed var ref. fix this.

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
7 years agoimx6: tqma6: rely on default setting for tftp and nfs
Markus Niebel [Fri, 3 Feb 2017 15:13:59 +0000 (16:13 +0100)]
imx6: tqma6: rely on default setting for tftp and nfs

Playing with USB-to-Ethernet dongles it turns out,
that these will not work with special settings

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
7 years agoarm: imx6: tqma6: add configurable CMA size
Markus Niebel [Fri, 3 Feb 2017 15:13:58 +0000 (16:13 +0100)]
arm: imx6: tqma6: add configurable CMA size

depending on the use case different CMA sizes are
needed for linux. Add env var to enable passing CMA size
via kernel command line

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
7 years agomtd: nand: build MXS driver for MX7 as well
Andrey Yurovsky [Fri, 10 Feb 2017 18:33:34 +0000 (10:33 -0800)]
mtd: nand: build MXS driver for MX7 as well

The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).

Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.

Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
7 years agomx6sx: udoo_neo: Enable distro boot options in config
Peter Robinson [Tue, 14 Feb 2017 13:10:12 +0000 (13:10 +0000)]
mx6sx: udoo_neo: Enable distro boot options in config

The include/configs/udoo_neo.h already includes the distro defaults
include files so it seems the board was missed in the move to the
config file, whether that in initial commit or conversion, so
enable the option now and remove duplicated settings.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
7 years agomx6sx: udoo_neo: use different load address for ramdisk
Peter Robinson [Tue, 14 Feb 2017 13:10:11 +0000 (13:10 +0000)]
mx6sx: udoo_neo: use different load address for ramdisk

The fdt_addr and ramdisk_addr_r are currently both defined to
0x83000000 and that's not going to work well for anyone. Move
the ramdisk_addr_r to 0x84000000.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
7 years agomx6sx: udoo_neo: Define the default serial console
Peter Robinson [Tue, 14 Feb 2017 13:10:10 +0000 (13:10 +0000)]
mx6sx: udoo_neo: Define the default serial console

Standard boot processes including distro boot generally expect the
default console to be defined.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
7 years agoDrop CONFIG_ENABLE_VBOOT
Tom Rini [Sat, 18 Feb 2017 00:47:53 +0000 (19:47 -0500)]
Drop CONFIG_ENABLE_VBOOT

This is no longer used anywhere.

Signed-off-by: Tom Rini <trini@konsulko.com>
7 years agoARM: DRA7xx: Fix memory allocation overflow
Andrew F. Davis [Wed, 15 Feb 2017 15:16:53 +0000 (09:16 -0600)]
ARM: DRA7xx: Fix memory allocation overflow

When using early malloc the allocated memory can overflow into the SRAM
scratch space, move NON_SECURE_SRAM_IMG_END down a bit to allow more
dynamic allocation at the expense of a slightly smaller maximum image
size.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
7 years agoda850: Add instructions to copy AIS image to an MMC card
ahaslam@baylibre.com [Mon, 13 Feb 2017 17:49:40 +0000 (18:49 +0100)]
da850: Add instructions to copy AIS image to an MMC card

The da850 soc's can boot from a external mmc card, but
the AIS image should be written to the correct sector.

Add instructions to copy the AIS image to a MMC card.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>