Paul Gortmaker [Fri, 18 Sep 2009 23:08:41 +0000 (19:08 -0400)]
sbc8548: enable access to second bank of flash
The sbc8548 has a 64MB SODIMM flash module off of CS6 that
previously wasn't enumerated by u-boot. There were already
BR6/OR6 settings for it [used by cpu_init_f()] but there
was no TLB entry and it wasn't in the list of flash banks
reported to u-boot.
The location of the 64MB flash is "pulled back" 8MB from
a 64MB boundary, in order to allow address space for the
8MB boot flash that is at the end of 32 bit address space.
This means creating two 4MB TLB entries for the 8MB chunk,
and then expanding the original boot flash entry to 64MB
in order to cover the 8MB boot flash and the remainder
(56MB) of the user flash.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Paul Gortmaker [Fri, 18 Sep 2009 23:08:40 +0000 (19:08 -0400)]
sbc8548: get_clock_freq is not valid for this board
The get_clock_freq() comes from freescale/common/cadmus.c and is
only valid for the CDS based 85xx reference platforms. It would
be nice if we could read the 33 vs. 66MHz status somehow, but in
the meantime, tie it to CONFIG_SYS_CLK_FREQ like all the other
non-CDS boards do.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Paul Gortmaker [Fri, 18 Sep 2009 23:08:39 +0000 (19:08 -0400)]
sbc8548: delete unused MPC8548CDS info carried over from port
There are a couple defines and PCI bridge quirks related to the PCI
backplane of the MPC8548CDS that have no meaning in the context of
the port to the sbc8548 board, so delete them.
Also, the form factor of the sbc8548 is a standalone board with a
single PCI-X and a single PCI-e slot. That pretty much guarantees
that it will never be a PCI agent itself, so the host/agent and root
complex/end node distinctions have been removed.
Similarly, since there is no physical connector mapping to PCI2, so
all references of PCI2 in the board support files have been removed
as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1020/P1011 SOCs support max 32bit DDR width as opposed to P2020/P2010
where max DDR data width supported is 64bit.
As a next step the DDR data width initialization would be made more dynamic
with more flexibility from the board perspective and user choice.
Going forward we would also remove the hardcodings for platforms with onboard
memories and try to use the FSL SPD code for DDR initialization.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Paul Gortmaker [Fri, 18 Sep 2009 23:08:46 +0000 (19:08 -0400)]
sbc8548: replace README with completely new document
The previous README.sbc8548 was pretty much content-free. Replace
it with something that actually gives the end user some relevant
hardware details, and also lists the u-boot configuration choices.
Also in the cosmetic department, fix the bogus line in the Makefile
that was carried over from the SBC8560 Makefile, and the typo in
the sbc8548.c copyright.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sat, 19 Sep 2009 16:20:54 +0000 (11:20 -0500)]
ppc/85xx: Clean up use of LAWAR defines
On 85xx platforms we shouldn't be using any LAWAR_* defines
but using the LAW_* ones provided by fsl-law.h. Rename any such
uses and limit the LAWAR_ to the 83xx platform as the only user so
we will get compile errors in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simon Kagstrom [Tue, 15 Sep 2009 07:53:29 +0000 (09:53 +0200)]
ubifs: Add support for looking up directory and relative symlinks
This patch adds support for resolving symlinks to directories as well as
relative symlinks. Symlinks are now always resolved during file lookup,
so the load stage no longer needs to special-case them.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Stefan Roese <sr@denx.de>
u-boot reports a PCIE PLL lock error at boot time on Yucca board, and
left PCIe nonfunctional. This is fixed by making u-boot function
ppc4xx_init_pcie() to wait 300 uS after negating reset before the
first check of the PLL lock.
Signed-off-by: Rupjyoti Sarmah <rsarmah@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
introduced a regression where platform-specific ffs/fls implementations
were defined away. This patch corrects that by using PLATFORM_xxx
instead of the name itself.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 14 Sep 2009 09:13:34 +0000 (11:13 +0200)]
ppc4xx: Consolidate get_OPB_freq()
All 4xx variants had their own, mostly identical get_OPB_freq()
function. Some variants even only had the OPB frequency calculated
in this routine and not supplied the sys_info.freqOPB variable
correctly (e.g. 405EZ). This resulted in incorrect OPB values passed
via the FDT to Linux.
This patch now removes all those copies and only uses one function
for all 4xx variants (except for IOP480 which doesn't have an OPB).
Stefan Roese [Fri, 11 Sep 2009 15:09:45 +0000 (17:09 +0200)]
ppc4xx: Enable commands for FDT enabled Linux booting on AMCC Acadia
Acadia still used the "old" arch/ppc bootm commands for booting
Linux images without FDT. This patch now enables these fdt-aware
boot commands for Acadia as well.
Kumar Gala [Fri, 11 Sep 2009 20:28:41 +0000 (15:28 -0500)]
ppc/85xx: Disable all async interrupt sources when we boot
We should make sure to clear MSR[ME, CE, DE] when we boot an OS image
since we have changed the exception vectors and the OSes vectors might
not be setup we should avoid async interrupts at all costs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mingkai Hu [Fri, 11 Sep 2009 02:53:08 +0000 (10:53 +0800)]
NAND boot: change NAND loader's relocate SP to CONFIG param
So that we can set the NAND loader's relocate stack pointer
to the value other than the relocate address + 0x10000.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mingkai Hu [Fri, 11 Sep 2009 06:19:10 +0000 (14:19 +0800)]
ppc/85xx: add boot from NAND/eSDHC/eSPI support
The MPC8536E is capable of booting form NAND/eSDHC/eSPI, this patch
implements these three bootup methods in a unified way - all of these
use the general cpu/mpc85xx/start.S, and load the main image to L2SRAM
which lets us use the SPD to initialize the SDRAM.
For all three bootup methods, the bootup process can be divided into two
stages: the first stage will initialize the corresponding controller,
configure the L2SRAM, then copy the second stage image to L2SRAM and
jump to it. The second stage image is just like the general U-Boot image
to configure all the hardware and boot up to U-Boot command line.
When boot from NAND, the eLBC controller will first load the first stage
image to internal 4K RAM buffer because it's also stored on the NAND
flash. The first stage image, also call 4K NAND loader, will initialize
the L2SRAM, load the second stage image to L2SRAM and jump to it. The 4K
NAND loader's code comes from the corresponding nand_spl directory, along
with the code twisted by CONFIG_NAND_SPL.
When boot from eSDHC/eSPI, there's no such a first stage image because
the CPU ROM code does the same work. It will initialize the L2SRAM
according to the config addr/word pairs on the fixed address and
initialize the eSDHC/eSPI controller, then load the second stage image
to L2SRAM and jump to it.
The macro CONFIG_SYS_RAMBOOT is used to control the code to produce the
second stage image for all different bootup methods. It's set in the
board config file when one of the bootup methods above is selected.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 11 Sep 2009 16:30:30 +0000 (11:30 -0500)]
ppc/85xx: Repack tlb_table to save space
We can pack the initial tlb_table in MAS register format and use
write_tlb to set things up. This savings can be helpful for NAND
style first stage boot loaders.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Thu, 20 Aug 2009 22:45:05 +0000 (17:45 -0500)]
ppc/85xx: Ensure that MAS8 is zero when writing TLB entries.
Its reset value is random, and we sometimes read uninitialized TLB
arrays. Make sure that we don't retain MAS8 from reading such an entry
if the VF bit in MAS8 is set, attempts to use the mapping will trap.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Mike Frysinger [Wed, 9 Sep 2009 16:20:21 +0000 (12:20 -0400)]
tools/netconsole: use ncb automatically if available
The standard netcat, while ubiquitous, doesn't handle broadcast udp packets
properly. The local ncb util does however. So if ncb can be located in
the standard locations, automatically use that instead.
Mike Frysinger [Wed, 9 Sep 2009 16:20:20 +0000 (12:20 -0400)]
tools/netconsole: make a bit more robust
The netcat utility likes to exit when it receives an empty packet (as it
thinks this means EOF). This can easily occur when working with command
line editing as this behavior will be triggered when using backspace. Or
with tabs and command line completion. So create two netcat processes -
one to only listen (and put it into a loop), and one to do the sending.
Once the user quits the transmitting netcat, the listening one will be
killed automatically.
Simon Kagstrom [Mon, 24 Aug 2009 07:10:12 +0000 (09:10 +0200)]
Define ffs/fls for all architectures
UBIFS requires fls(), which is not defined for arm (and some other
architectures) and this patch adds it. The implementation is taken from
Linux and is generic. ffs() is also defined for those that miss it.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Simon Kagstrom [Mon, 24 Aug 2009 07:09:50 +0000 (09:09 +0200)]
Move __set/clear_bit from ubifs.h to bitops.h
__set_bit and __clear_bit are defined in ubifs.h as well as in
asm/include/bitops.h for some architectures. This patch moves
the generic implementation to include/linux/bitops.h and uses
that unless it's defined by the architecture.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Wolfgang Denk [Tue, 15 Sep 2009 20:12:31 +0000 (22:12 +0200)]
mkconfig: split the board make target to multiple config targets
To simplify the top level makefile it useful to be able to parse
the top level makefile target to multiple individual target, then
put them to the config.h, leave the board config file to handle
the different targets.
Note that this method uses the '_'(underline) as the delimiter when
splits the board make target.
Wolfgang Denk [Fri, 11 Sep 2009 09:44:39 +0000 (11:44 +0200)]
board/amcc/taihu/flash.c: Fix compile warning
Fix warnings:
flash.c: In function 'write_word_1':
flash.c:696: warning: dereferencing type-punned pointer will break strict-aliasing rules
flash.c: In function 'write_word_2':
flash.c:1044: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Fri, 11 Sep 2009 09:37:20 +0000 (11:37 +0200)]
board/etin/debris/phantom.c: Fix compile error
Fix build problem caused by commit e84aba13: "Replace BCD2BIN and
BIN2BCD macros with inline functions"
phantom.c:163: error: redefinition of 'bcd2bin'
/home/wd/git/u-boot/work/include/bcd.h:16: error: previous definition of 'bcd2bin' was here
phantom.c:168: error: redefinition of 'bin2bcd'
/home/wd/git/u-boot/work/include/bcd.h:21: error: previous definition of 'bin2bcd' was here
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Sangmoon Kim <dogoil@etinsys.com>
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Stefan Roese <sr@denx.de>
Stefan Roese [Wed, 9 Sep 2009 14:25:29 +0000 (16:25 +0200)]
ppc4xx: Big cleanup of PPC4xx defines
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Wolfgang Denk [Fri, 11 Sep 2009 06:58:11 +0000 (08:58 +0200)]
kwbimage.c: Fix compile warning when building on 64 bit systems
Fix this warning when building on 64 bit systems:
tools/kwbimage.c: In function 'kwbimage_checksum32':
tools/kwbimage.c:135: warning: format '%d' expects type 'int',
but argument 4 has type 'long unsigned int'
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com>
Currently it is used by image.c only, but the the function can be
used to support additional mkimage types like for example kwbimage,
so make this function globally visible.
mkimage: Include missing files in build dependency calculations
Include default_image.o and fit_image.o into the build dependency
calculations. This makes sure they get rebuilt if any of the headers
they include are modified
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Ron Lee <ron@debian.org>
Edited commit message.
Wolfgang Denk [Wed, 19 Aug 2009 09:42:56 +0000 (11:42 +0200)]
tools/mkimage: fix compiler warnings, use "const"
This fixes some compiler warnings:
tools/default_image.c:141: warning: initialization from incompatible pointer type
tools/fit_image.c:202: warning: initialization from incompatible pointer type
and changes to code to use "const" attributes in a few places where
it's appropriate.
tools: mkimage: split code into core, default and FIT image specific
This is a first step towards reorganizing the mkimage code to make it
easier to add support for additional images types. Current mkimage
code is specific to generating uImage and FIT image files, but the
same framework can be used to generate other image types like
Kirkwood boot images (kwbimage-TBD). For this, the mkimage code gets
reworked:
Here is the brief plan for the same:-
a) Split mkimage code into core and image specific support
b) Implement callback functions for image specific code
c) Move image type specific code to respective C files
Currently there are two types of file generation/list
supported (i.e uImage, FIT), the code is abstracted from
mkimage.c/.h and put in default_image.c and fit_image.c;
all code in these file is static except init function call
d) mkimage_register API is added to add new image type support
All above is addressed in this patch
e) Add kwbimage type support to this new framework (TBD)
This will be implemented in a following commit.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Edit commit message, fix coding style and typos. Signed-off-by: Wolfgang Denk <wd@denx.de>
ppc4xx: Allow overwriting pci target registers for all 4xx boards
This patch adds the CONFIG_PCI_4xx_PTM_OVERWRITE option and replaces
the ugly 'if defined(BOARD1) || ... || defined(BOARDn)' construct
in 4xx pci code.
When CONFIG_PCI_4xx_PTM_OVERWRITE is defined the default ptm register
setup can be overwritten through environment variables ptm1la, ptm1ms,
ptm2la and ptm2ms to do application specific pci target BAR configuration.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot / log