Stefan Roese [Tue, 20 Feb 2007 09:51:26 +0000 (10:51 +0100)]
[PATCH] I2C: Add support for multiple I2C busses for RTC & DTT
This patch switches to the desired I2C bus when the date/dtt
commands are called. This can be configured using the
CFG_RTC_BUS_NUM and/or CFG_DTT_BUS_NUM defines.
Stefan Roese [Tue, 20 Feb 2007 09:43:34 +0000 (10:43 +0100)]
[PATCH] PPC4xx: Add 440SP(e) DDR2 SPD DIMM support
This patch adds support for the DDR2 controller used on the
440SP and 440SPe. It is tested on the Katmai (440SPe) eval
board and works fine with the following DIMM modules:
- Corsair CM2X512-5400C4 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5/512 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5K2/2G (1GByte per DIMM)
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
Stefan Roese [Tue, 20 Feb 2007 09:35:42 +0000 (10:35 +0100)]
[PATCH] PPC4xx: Split 4xx SPD SDRAM init routines into 2 files
Since the existing 4xx SPD SDRAM initialization routines for the
405 SDRAM controller and the 440 DDR controller don't have much in
common this patch splits both drivers into different files.
This is in preparation for the 440 DDR2 controller support (440SP/e).
Stefan Roese [Tue, 20 Feb 2007 09:27:08 +0000 (10:27 +0100)]
[PATCH] PPC4xx: Add support for multiple I2C busses
This patch adds support for multiple I2C busses on the PPC4xx
platforms. Define CONFIG_I2C_MULTI_BUS in the board config file
to make use of this feature.
It also merges the 405 and 440 i2c header files into one common
file 4xx_i2c.h.
Also the 4xx i2c reset procedure is reworked since I experienced
some problems with the first access on the 440SPe Katmai board.
Stefan Roese [Fri, 2 Feb 2007 11:44:22 +0000 (12:44 +0100)]
[PATCH] Correctly display PCI arbiter en-/disabled on some 4xx boards
Previously the strapping DCR/SDR was read to determine if the internal PCI
arbiter is enabled or not. This strapping bit can be overridden, so now
the current status is read from the correct DCR/SDR register.
Stefan Roese [Thu, 1 Feb 2007 12:22:41 +0000 (13:22 +0100)]
[PATCH] Remove PCI-PNP configuration from Sequoia/Rainier config file
When PCI PNP is enabled the pci pnp configuration routine is called
which sets the PCI_CACHE_SIZE_LINE to 8. This seems to generate some
problems with some PCI cards. For now disable the PCI PNP configuration.
Stefan Roese [Tue, 30 Jan 2007 16:06:10 +0000 (17:06 +0100)]
[PATCH] Update Sequoia (440EPx) config file
The config file now handles the 2nd target, the Rainier (440GRx)
evaluation board better. Additionally the PPC input clock was
adjusted to match the correct value of 33.0 MHz.
Stefan Roese [Tue, 30 Jan 2007 16:04:19 +0000 (17:04 +0100)]
[PATCH] Merge Yosemite & Yellowstone board ports
Now the AMCC eval boards Yosemite (440EP) and Yellowstone (440GR)
share one config file and all board specific files. This way we
don't have to maintain two different sets of files for nearly
identical boards.
Bartlomiej Sieka [Tue, 23 Jan 2007 13:21:14 +0000 (14:21 +0100)]
[iDMR] Flash driver on initialisation write-protects some sectors,
currently sectors 0-3. Sector 3 does not need to be protected, though
(U-boot occupies sectors 0-1 and the environment sector 2). This commit
fixes this, i.e., only sectors 0-2 are protected.
Bartlomiej Sieka [Tue, 23 Jan 2007 13:11:22 +0000 (14:11 +0100)]
[iDMR] Using MII-related commands on iDRM board doesn't work now (e.g.,
"mii device" results in "Unexpected exception"). Fixing this properly
requires some clean-up in the FEC drivers infrastructure for ColdFire, so
this commit disables MII commads for now.
Wolfgang Denk [Wed, 10 Jan 2007 00:28:39 +0000 (01:28 +0100)]
Fix auto_update for MCC200 board.
The invocation of do_auto_update() is moved to the end of the
misc_init_r() function, after the flash mappings have been
initialized. Please find attached a patch that implements that
change.
Also correct the decoding of the keypad status. With this update, the
key that will trigger the update is Column 2, Row 2.
CAM5200 flash driver modifications:
- use CFI driver (replaces custom flash driver) for main 'cam5200' target
- add second build target 'cam5200_niosflash' which still uses custom driver
Stefan Roese [Fri, 5 Jan 2007 10:46:05 +0000 (11:46 +0100)]
[PATCH] nand: Fix problem with oobsize calculation
Here the description from Brian Brelsford <Brian_Brelsford@dell.com>:
The Hynix part returns a 0x1d in the 4th ID byte. The Samsung part
returns a 0x15. In the code fragment below bits [1:0] determine the
page size, it is ANDed via "(extid & 0x3)" then shifted out. The
next field is also ANDed with 0x3. However this is a one bit field
as defined in the Hynix and Samsung parts in the 4th ID byte that
determins the oobsize, not a two bit field. It works on Samsung as
bits[3:2] are 01. However for the Hynix there is a 11 in these two
bits, so the oob size gets messed up.
I checked the correct linux code and the suggested fix from Brian is
also available in the linux nand mtd driver.
Bartlomiej Sieka [Thu, 28 Dec 2006 18:08:21 +0000 (19:08 +0100)]
Few V38B changes:
- fix a typo in V38B config file
- move watchdog initialisation earlier in the boot process
- add "wdt=off" to default kernel command line (disables kernel watchdog)
Stefan Roese [Wed, 29 Nov 2006 14:42:37 +0000 (15:42 +0100)]
[PATCH] Add support for Prodrive P3M750 & P3M7448 (P3Mx) boards
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".
Stefan Roese [Wed, 29 Nov 2006 11:53:15 +0000 (12:53 +0100)]
[PATCH] common/cmd_elf.c: Enable loadaddr as parameter in bootvx command
In the bootvx command the load address was only read from the env
variable "loadaddr" and not optionally passed as paramter as described
in the help. This is fixed with this patch. The behaviour is now the
same as in the bootelf command.