Jim Paris [Mon, 22 Aug 2011 20:48:14 +0000 (16:48 -0400)]
Fix redbee config files
Currently the board/redbee-*.cfg files incorrectly include the
interface definition. Move the interfaces to interface/,
and create a single board/redbee.cfg that is common to both boards.
Intended usage is now:
openocd -f interface/redbee-econotag.cfg -f board/redbee.cfg
Spencer Oliver [Wed, 10 Aug 2011 21:23:29 +0000 (22:23 +0100)]
ftd2xx: fix build warnings
Due to build warnings introduced in newer versions of ftd2xx we
use strings to report errors rather than result codes. This also
gives us the same behaviour as libftdi.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Rodrigo L. Rosa [Fri, 5 Aug 2011 18:38:12 +0000 (11:38 -0700)]
renamed for clarity
i had started my code from dsp5683xx, i renamed a bunch of stuff to names i consider to be better.
i believe no one is using this code, so nobody should be affected. (it's not too late to do this change)
After correcting the reply size counter, it should be safe to rely on it
for the number of bytes expected in the USB read, instead of reading the
endpoint maximum. This doesn't make things go any faster but it's nicer and
removes the local buffer.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
rlink: simplify and optimize queue fill level checks
Add a helper function for running the queue if it would overflow otherwise.
Use it to simplify the queue fill level checks and optimize in a few cases
that would previously run the queue prematurely.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
rlink: fix reply counter to enable sending full buffers
dtc_queue.reply_index was wrongly being increased during out scans, causing
the queue to be sent before the out buffer was full. This patch increases
raw upload speed by 50% or so.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Function mips_m4k_write_memory() does endianess byte swap,
but this procedure break one byte access (temporary array
overwrites content in buffer).
As a fix, this endianess swap and buffer affecting
is preformed only on hword and word accesses (not on byte access).
mips32: Sync Caches to Make Instr Writes Effective
Pprogram that loads another program into memory is actually writing the
D- side cache.
The instructions it has loaded can't be executed until they reach the
I-cache.
After the instructions have been written, the loader should arrange to
write back any containing D-cache line and invalidate any locations
already in the I-cache.
For the MIPS Architecture Release2 cores, we can use synci command
that does this job.
For Release1 we must use "cache" instruction.
For all architectures we use distinct common magic number,
and this should be a uint32_t type.
Otherwise, comparison with macros will yield compilation
warning.
Rodrigo L. Rosa [Tue, 9 Aug 2011 18:25:23 +0000 (11:25 -0700)]
fix tapenabler return code
if tap enable/disable failed then a warning was written to the log, but JIM_OK was returned. if using openocd via a TCP interface to the TCL port, there is no way to catch that the command failed (it didn't enable the tap, so it failed)
now it return an error if it fails.
Andreas Bießmann [Tue, 12 Jul 2011 10:38:22 +0000 (12:38 +0200)]
flash/nor/cfi: fix TopBottom for atmel chips
There are some older atmel nor chips which have negated logic for
TopBottom detection. This patch adds a special handling for the old
chips. This is the same mechanism as implemented in linux kernel.
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
Rodrigo L. Rosa [Wed, 20 Jul 2011 03:03:08 +0000 (20:03 -0700)]
dsp5680xx fix FM clk
before doing anything with the flash module (FM) the clock divider must be set.
if erase_check was the first thing done with the FM after reset then an error would be generated because the clk divider was not set.
now erase_check sets the clk divider.
Rodrigo L. Rosa [Wed, 20 Jul 2011 03:01:19 +0000 (20:01 -0700)]
dps5680xx fix warnings
reorganized code to get rid of compiler warnings
the warning were related to allignment, i do not get these warning on my build system (i've tried setting the compiler flag but it doesn't work, still working on why) so i cannot detect them (yet.)
Luca Bruno [Sat, 9 Jul 2011 21:44:39 +0000 (23:44 +0200)]
Do not append git info to version string when building from released tarball
When building official releases from tarball, git commit info is not
available in the building environment. Thus, automake should not try to
append the git commit to the version string.
Signed-off-by: Luca Bruno <lucab@debian.org> Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Peter Horn [Mon, 4 Jul 2011 10:25:26 +0000 (11:25 +0100)]
cortex_m3: add auto maskisr
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
In order to compare data read from the target with some marcros or data
defined on the host, we must transform this read data from target
endianess to host endianess.
target_read_memory() gets bytes from target to the host, but keeps them in _target_
endianess. This is OK if we just want to temporary keep this data on the
host, like keeping breakpoint->orig_instr. But if we want to use this
data for any ispections and comparisons on the host side, we must
transform it to _host_ endianess, by using target_buffer_get_u32()
function.
Currently this transformation is missing, and check current_instr ==
MIPS32_SDBBP will never pass if target and host endianess differ,
because current_instr will be kept in _target_ endianess and
MIPS32_SDBBP will be kept in _host_ endianess,
The patch fix this issue by using target_buffer_get_u32() to transform current_instr to
_host_ endianess before comparison.
Øyvind Harboe [Tue, 28 Jun 2011 16:35:34 +0000 (18:35 +0200)]
dsp5680xx: disable for now, it generates warnings
Use "git revert <commit>" to revert this commit, then build and
repair and post patch to the mailing list.
Warnings generated with:
nios2-elf-gcc (GCC) 3.4.6 (Altera Nios II 9.1 b222)
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_upper_data':
openocd/src/target/dsp5680xx.c:252: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_lower_data':
openocd/src/target/dsp5680xx.c:268: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_pc_store':
openocd/src/target/dsp5680xx.c:508: warning: dereferencing type-punned
pointer will break strict-aliasing rules
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_read':
openocd/src/target/dsp5680xx.c:736: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:737: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write_8':
openocd/src/target/dsp5680xx.c:823: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write':
openocd/src/target/dsp5680xx.c:938: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:941: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_f_wr':
openocd/src/target/dsp5680xx.c:1355: warning: cast increases required
alignment of target type
Spencer Oliver [Tue, 28 Jun 2011 13:16:48 +0000 (14:16 +0100)]
cortex_m3: add auto maskisr
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
projects / openocd / log