Nishanth Menon [Tue, 26 Mar 2013 05:20:52 +0000 (05:20 +0000)]
twl6030: move twl6030 register access functions to common header file
twl6030_i2c_[read|write]_u8 can be used else where to access
multi-function device such as twl6030, so move the register access
functions to the common twl6030.h header file.
u-boot standard i2c register access prototype is
i2c_read(addr, reg, 1, &buf, 1)
i2c_reg_write(u8 addr, u8 reg, u8 val)
twl6030_i2c_read_u8(u8 addr, u8 *val, u8 reg)
twl6030_i2c_write_u8(u8 addr, u8 val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl6030_i2c_read_u8(u8 addr, u8 reg, u8 *val)
twl6030_i2c_write_u8(u8 addr, u8 reg, u8 val)
Nishanth Menon [Tue, 26 Mar 2013 05:20:50 +0000 (05:20 +0000)]
twl4030: make twl4030_i2c_read_u8 prototype consistent
u-boot standard i2c read prototype is
i2c_read(addr, reg, 1, &buf, 1)
twl4030_i2c_read_u8(u8 addr, u8 *val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_read_u8(u8 addr, u8 reg, u8 *val)
Nishanth Menon [Tue, 26 Mar 2013 05:20:49 +0000 (05:20 +0000)]
twl4030: make twl4030_i2c_write_u8 prototype consistent
u-boot standard i2c register write prototype is
i2c_reg_write(u8 addr, u8 reg, u8 val)
twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val)
Matt Porter [Wed, 20 Mar 2013 05:38:13 +0000 (05:38 +0000)]
phy: add support for ET1011C phys
Adds an ET1011C PHY driver which is derived from the
Linux kernel PHY driver (drivers/net/phy/et1011c.c)
from the v3.9-rc2 tag. Note that an errata workaround
config option is implemented to allow for TX_CLK to be
enabled even when gigabit mode is negotiated. This
workaround is used on the PG1.0 TI814X EVM.
Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
Simon Glass [Thu, 18 Apr 2013 10:25:51 +0000 (10:25 +0000)]
crc32: Correct endianness of crc32 result
When crc32 is handled by the hash library, it requires the data to be in
big-endian format, since it reads it byte-wise. Thus at present the 'crc32'
command reports incorrect data. For example, previously we might see:
Andreas Bießmann [Mon, 15 Apr 2013 23:52:18 +0000 (23:52 +0000)]
patman: fix gitutil for decorations
The git config parameter log.decorate is quite useful when working with git.
Patman, however can not handle the decorated output when parsing the commit.
To prevent this use the '--no-decorate' switch for git-log.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 11 Mar 2013 06:30:27 +0000 (06:30 +0000)]
fdt: Ensure that libfdt_env.h comes from U-Boot
When building host utilities, we include libfdt.h from the host, not from
U-Boot. This in turn brings in libfdt_env.h from the host, which can mess
up the types and cause a build failure, depending on the host environment.
To fix this, force inclusion of U-Boot's libfdt_env.h so that the types
are correct.
Another way to fix this is to use -nostdinc and -idirafter to ensure that
system includes are included after U-Boot ones. Unfortunately this means
that U-Boot's errno.h gets included instead of the system one. This in
turn requires a hack to errno.h to redirect things, so all in all the
solution in this patch is probably cleaner.
Jaehoon Chung [Tue, 29 Jan 2013 19:31:16 +0000 (19:31 +0000)]
mmc: support the correct card version for eMMC
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Maxime Larocque [Fri, 28 Sep 2012 05:00:13 +0000 (05:00 +0000)]
printenv: Correct out-of-memory condition check.
In common/cmd_nvedit.c, en env_print(), the wrong type is used for len.
hexport_r() returns -1 on error (like OOM), which is converted to
0xffffffff when put in an unsigned. Said value is obviously bigger then
0, and as a result an uninitialized string is then displayed. Other
usages of hexport_r() in the code correctly uses ssize_t to keep its
return value.
Signed-off-by: Maxime Larocque <maxmtl2002@yahoo.ca>
Simon Glass [Sat, 13 Apr 2013 04:26:41 +0000 (04:26 +0000)]
exynos: Correct use of 64-bit division
The current code is causing errors like this on my toolchains:
/usr/x86_64-pc-linux-gnu/armv7a-cros-linux-gnueabi/binutils-bin/2.22/
ld.bfd.real: failed to merge target specific data of file /usr/lib/gcc/
armv7a-cros-linux-gnueabi/4.7.x-google/libgcc.a(_divdi3.o)
Use do_div() to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Vivek Gautam [Mon, 28 Jan 2013 00:39:59 +0000 (00:39 +0000)]
Exynos5: Add support for USB download boot mode
Exynos5250 supports secondary USB device boot mode. If the iROM fails
to download u-boot from the primary boot device (such as SD or eMMC),
it will try to retrieve from the secondary boot device (such as USB).
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Simon Glass [Mon, 15 Apr 2013 11:25:20 +0000 (11:25 +0000)]
x86: Allow setup code to manage its own global data
Currently x86 has its own means of managing the global data and board data
(bd_t), and this code resides in start.S. With generic board, we need to
ensure that we leave this alone - i.e. don't clear it as we do on other
archs.
This fixes a problem where the memory init data is cleared which causes
the video driver to operate very slowly.
Simon Glass [Mon, 15 Apr 2013 11:22:49 +0000 (11:22 +0000)]
x86: Fix DRAM bank size init with generic board
The intention of the memory init code is that it should work the same with
CONFIG_SYS_GENERIC_BOARD and without. This is tricky because dram_init()
is called prior to relocation with generic board (matching other archs)
and after relocation without generic board.
Adjust the init sequence so that dram_init() is not called in the generic
board case, which seems like the easiest fix for now. Also ensure that
relocation addresses are still calculated.
Tom Warren [Wed, 10 Apr 2013 17:32:32 +0000 (10:32 -0700)]
Tegra: Split tegra_get_chip_type() into soc & sku funcs
As suggested by Stephen Warren, use tegra_get_chip() to return
the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for
Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true
function, i.e. tegra_get_chip_sku(), which returns an ID like
TEGRA_SOC_T25, TEGRA_SOC_T33, etc.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Wed, 3 Apr 2013 21:39:30 +0000 (14:39 -0700)]
Tegra: Fix MSELECT clock divisors for T30/T114.
A comparison of registers between our internal NV U-Boot and
u-boot-tegra/next showed some discrepancies in the MSELECT
clock divisor programming. T20 doesn't have a MSELECT clk src reg.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Mon, 1 Apr 2013 22:48:54 +0000 (15:48 -0700)]
Tegra114: Initialize System Counter (TSC) with osc frequency
T114 needs the SYSCTR0 counter initialized so the TSC can be
read by the kernel. Do it in the bootloader since it's a write-once
deal (secure/non-secure mode dependent).
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Boot script support brings TEC in line with other Tegra boards. To
enable booting a Linux kernel with initial ramdisk, also include support
for the new FIT image type.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tegra: Plutux: Enable NAND and boot script support
Boot script support brings Plutux in line with other Tegra boards. In
order to enable booting a Linux kernel with initial ramdisk, also add
support for the new FIT image type.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tegra: Medcom-Wide: Enable NAND and boot script support
Boot script support brings Medcom-Wide in line with other Tegra boards.
In order to enable booting a Linux kernel with initial ramdisk, also add
support for the new FIT image type.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Thu, 28 Mar 2013 17:03:22 +0000 (10:03 -0700)]
Tegra: Restore cp15 VBAR _start vector write for ARMv7
A start vector fix was added by AneeshV for OMAP4 (commit 0d479b53),
and caused the old monilithic Tegra builds to hang due to an undefined
instruction trap. Previously, the code needed to run on both the
AVP (ARM7TDI) and A9, and the AVP doesn't have a CP15 register.
I corrected this in commit 6d6c0bae w/#ifndef CONFIG_TEGRA, but
now that we use SPL, and boot the AVP w/o any ARMv7 code, I can
revert my change, and make Aneesh's change apply to Tegra.
Stephen Warren [Wed, 27 Mar 2013 09:37:02 +0000 (09:37 +0000)]
ARM: tegra: support T33 SKU of Tegra30
Make U-Boot aware of the T33 SKU of Tegra30, and treat it identically
to any other Tegra30.
An alternative would be to simply remove the SKU checking from
tegra_get_chip_type(); most use of the value most likely simply wants
to know the current chip, not the specific SKU. Or, the function could
be split into separate tegra_get_chip() and tegra_get_sku() for the
cases where differentiation really is required.
I wonder whether tegra_get_chip_type() should printf() whenever any
unkown chip/SKU is found, although perhaps the function is called so
early that the printf() wouldn't actually make it to the UART anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Andre Przywara [Tue, 2 Apr 2013 05:43:36 +0000 (05:43 +0000)]
ARMv7: start.S: stay in HYP mode if u-boot is entered in it
The KVM and Xen hypervisors for the Cortex-A15 virtualization
implementation need to be entered in HYP mode. Should the primary
board firmware already enter HYP mode (Calxeda firmware does that),
we should not deliberately drop back to SVC mode.
Since U-boot does not use the MMU, running in HYP mode is just fine.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Albert ARIBAUD [Fri, 12 Apr 2013 05:14:30 +0000 (05:14 +0000)]
ARM: fix CONFIG_SPL_MAX_SIZE semantics
Remove SPL-related ASSERT() in arch/arm/cpu/u-boot.lds
as this file is never used for SPL builds.
Rewrite the ASSERT() in arch/arm/cpu/u-boot-spl.lds
to separately test image (text,data,rodata...) size,
BSS size, and full footprint each against its own max,
and make Tegra boards check full footprint.
Also, output section mmutable is not used in SPL builds.
Remove it.
Finally, update README regarding the (now homogeneous)
semantics of CONFIG_SPL_[BSS_]MAX_SIZE and add the new
CONFIG_SPL_MAX_FOOTPRINT macro.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Andrew Gabbasov [Sun, 7 Apr 2013 23:06:08 +0000 (23:06 +0000)]
fsl_esdhc: Fix DMA transfer completion waiting loop
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Albert ARIBAUD [Thu, 11 Apr 2013 05:43:21 +0000 (05:43 +0000)]
ARM: Fix __bss_start and __bss_end in linker scripts
Commit 3ebd1cbc introduced compiler-generated __bss_start
and __bss_end__ and commit c23561e7 rewrote all __bss_end__
as __bss_end. Their merge caused silent and harmless but
potentially bug-inducing clashes between compiler- and linker-
generated __bss_end symbols.
Make __bss_end and __bss_start compiler-only, and create
__bss_base and __bss_limit for linker-only use.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The glitch in the SPI clock line, which commit 3cea335c34 (spi: mxc_spi: Fix spi
clock glitch durant reset) solved, is back now and itwas re-introduced by
commit d36b39bf0d (spi: mxc_spi: Fix ECSPI reset handling).
Actually the glitch is happening due to always toggling between slave mode
and master mode by configuring the CHANNEL_MODE bits in this reset function.
Since the spi driver only supports master mode, set the mode for all channels
always to master mode in order to have a stable, "glitch-free" SPI clock line.
When swi instruction is executed, it is expected to get message
"software interrupt" in console and dump registers and reboot, as
do_software_interrupt() in arch/arm/lib/interrupts.c.
But, actually it causes data abort accessing wrong address in get_bad_stack_swi
macro in arch/arm/cpu/v7/start.S.
This patch fixes this problem.
The same mistake in arch/arm/cpu/{arm1136,arm1176,pxa}/start.S.
Che-liang Chiou [Thu, 28 Feb 2013 09:34:57 +0000 (09:34 +0000)]
tpm: Add TPM command library
TPM command library implements a subset of TPM commands defined in TCG
Main Specification 1.2 that are useful for implementing secure boot.
More TPM commands could be added out of necessity.
You may exercise these commands through the 'tpm' command. However, the
raw TPM commands are too primitive for writing secure boot in command
interpreter scripts; so the 'tpm' command also provides helper functions
to make scripting easier.
For example, to define a counter in TPM non-volatile storage and
initialize it to zero:
$ tpm init
$ tpm startup TPM_ST_CLEAR
$ tpm nv_define d 0x1001 0x1
$ tpm nv_write d 0x1001 0
And then increment the counter by one:
$ tpm nv_read d 0x1001 i
$ setexpr.l i $i + 1
$ tpm nv_write d 0x1001 $i
Rong Chang [Fri, 12 Apr 2013 10:44:57 +0000 (10:44 +0000)]
tpm: Add Infineon slb9635_i2c TPM driver
Add a driver for the I2C TPM from Infineon.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Rong Chang <rongchang@chromium.org> Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 12 Apr 2013 16:38:16 +0000 (12:38 -0400)]
am335x: Really correct DDR timings on new BeagleBone part
The previous timings were done on the internal-only A1 board which has
different DDR part than all later revs. The timings need a slight
adjustment to be correct in all cases with later revs.
Holger Brunck [Tue, 15 Jan 2013 22:51:22 +0000 (22:51 +0000)]
arm/km: add support for kmsuv31 board
This board is from a u-boot point of view a mixture between kmnusa and
a standard km_kirkwood board. We have our u-boot environment in the spi
NOR flash, but we have a direct connection between the kirkwood and the
piggy. A FPGA is connected via the PCIe interface. So we only have to
select the specific features in the board setup.
Holger Brunck [Tue, 15 Jan 2013 22:51:20 +0000 (22:51 +0000)]
arm/km: rename BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
commit 9660e442 cosmetic: s/BOARD_LATE_INIT/CONFIG_BOARD_LATE_INIT
removes BOARD_LATE_INIT and uses CONFIG_BOARD_LATE_INIT instead.
Therefore we have to use this define.
arm: Make all linker scripts compatible with per-symbol sections
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.
Following the removal of the smdk6400 board, the MMU setup code in
arm1176/start.S becomes unused, so remove it. It will still be possible to
restore it later from the Git history if necessary, in which case it should be
moved out of the relocate_code() function.
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
The migration of boards from Makefile to boards.cfg was due for v2012.03, but
smdk6400 did not follow, and it does not build, so move it to scrapyard. It will
still be possible to restore it from the Git history before fixing it.
make never uses the SHELL variable from the environment. Instead, it
uses /bin/sh, or the value assigned to the SHELL variable by the Makefile. This
makes the export of the SHELL variable useless for sub-makes (but still useful
for the environment of recipes). However, we want all makes to use the same
shell.
This patch fixes this issue by moving the SHELL variable setup and export to the
top config.mk, so that all Makefile-s including it use the same shell.
Since BASH is used by default, this makes it possible to use things
like 'echo -e ...' in sub-makes, which would otherwise fail e.g. with /bin/sh
symlinked to /bin/dash on Ubuntu.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Reviewed-by: Tom Rini <trini@ti.com>
Commit e05e5de7fae5bec79617e113916dac6631251156 made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.
projects / u-boot / log