Patch b6d7852c increases timeout for enumeration, taking
worst case to be 10 sec.
get_timer() api returns timestamp in milliseconds, which is
what we are checking in the do-while() loop in usb_hub_configure()
(get_timer(start) < CONFIG_SYS_HZ * 10).
This should give us a required check for 10 seconds, and thereby
we don't need to add additional mdelay of 100 microseconds in
each cycle.
usb: common: Weed out USB_**_PRINTFs from usb framework
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF
are nothing but conditional debug prints, depending on DEBUG.
So better remove them and use debug() simply.
Julius Werner [Thu, 28 Feb 2013 18:08:40 +0000 (18:08 +0000)]
usb: Add new command to set USB 2.0 port test modes
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Tom Rini [Fri, 3 May 2013 13:19:43 +0000 (09:19 -0400)]
P1022DS: Set CONFIG_SPL_MAX_SIZE directly
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with
CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to
CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather
than 4 * 1024.
Shaohui Xie [Mon, 25 Mar 2013 07:30:15 +0000 (07:30 +0000)]
powerpc/85xx: set USB2 default mode to 'device' for (super)hydra boards
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a
second USB port that can be configured in either host, peripheral (aka
device), or OTG (on-the-go) mode. When configured in host mode, if
the port is connected to another USB host, damage to the board can
occur.
To avoid this, we change the default setting to peripheral mode. Ideally,
we'd set it to OTG mode, but currently there is no OTG support for
these boards.
Setting the hwconfig variable will also update the device tree, and so
Linux will configure the port for peripheral mode as well.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Timur Tabi <timur@tabi.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
Xu Jiucheng [Mon, 25 Mar 2013 07:30:13 +0000 (07:30 +0000)]
powerpc/p1_p2_rdb_pc: Add a pin to reset the DDR chip for P1021RDB-PC
When P1021RDB-PC reboot system, the board will hung at uboot DDR
configuration. For P1021RDB-PC DDR reset pin is multiplex with
QE, so uboot will reserve this pin for QE and skip DDR reset.
Other platforms without QE will do this reset. This patch adds
a slight code to reset DDR chip by QE CE_PB8 pin for NAND and
NOR FLASH boot. For booting from SPI FALSH and SD card, it
seems possible to use the rom on chip to write to the GPIO
pins before configuring the DDR.
Extending LIODN offset range from 1-5 to 1-10
While using a qman portal with a higher index the LIODN offset
is incorrectly set, thus extending the range of offsets covers
all 10 qman portals
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com> Acked-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Zhicheng Fan [Mon, 25 Mar 2013 07:30:07 +0000 (07:30 +0000)]
qoriq/p1_p2_rdb_pc: USB device-tree fixups for P1020
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Zhicheng Fan <B32736@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Poonam Aggrwal [Mon, 25 Mar 2013 07:30:06 +0000 (07:30 +0000)]
doc/ramboot.mpc85xx: Documented the RAMBOOT for MPC85xx
There could be scenarios where the user would like to manually(via JTAG)
configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SRAM.
This document explains thse usecases and the detailed explanation of what needs
to be done to use it.
Most of the code from CONFIG_SYS_RAMBOOT will be used except for small changes
of CCSRBAR etc.
The changes are not very large, but it is good to document them so that user
can get it working at once.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Xulei [Mon, 11 Mar 2013 17:56:34 +0000 (17:56 +0000)]
powerpc/85xx: Add workaround for errata USB-14 (enable on P204x/P3041/P50x0)
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.
In formal release document, the errata number should be USB14 instead of USB138.
Signed-off-by: xulei <Lei.Xu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: xulei <B33228@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Zang Roy-R61911 [Mon, 4 Mar 2013 03:59:20 +0000 (03:59 +0000)]
fman/mEMAC: set SETSP bit in IF_MODE regisgter for RGMII speed
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Reported-by: John Traill <john.traill@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
powerpc/p1022ds: Add support for NAND and NAND boot using SPL
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
powerpc/mpc85xx: Add revision properties in portal device tree node 'pme'
The 'fsl,pme-rev1' and 'fsl-pme-rev2' properties have been added to the
pme portal node. This is required for software to determine which version
of PME hardware is present and take appropriate actions.
These properties are a direct reflection of the corresponding ccsr pme
register value.
Also removed unnecessary static global variables.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Jiang Bin [Mon, 19 Nov 2012 22:31:24 +0000 (22:31 +0000)]
board/freescale/common/cds_pci_ft.c: Fix rotate wrong cells in interrupt-map property
For linux 3.x, the size of each item in interrupt-map property is 9 not 7.
Don't use the static value and calculate the size with following cells:
PCI #address-cells, PCI #interrupt-cells,
PIC address, PIC #address-cells, PIC #interrupt-cells.
Signed-off-by: Bin Jiang <bin.jiang@windriver.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Stefan Roese [Thu, 25 Apr 2013 23:20:23 +0000 (23:20 +0000)]
mpc5200: a3m071/a4m2k: Miscellaneous updates and fixes
The changes to a3m071/a4m2k in summary are:
- Enable CAN1 on I2C in GPS Port Configuration
- Enable SPI on PSC2
- Activate network console
- New flash partitioning
- Fix some typos
- Pass host name to Linux
- Change rootfs to squashfs,jffs2
- Enable UBI/UBIFS support
- Enable FIT support
With this, the global_data struct is now common and new variables
have been added. Resulting in a bigger struct. Unfortunately the
currently allocated 128 bytes are just a bit too small for this
new struct.
This patch now uses the automatically generated struct size instead to
not run into this problem again.
Please note that this problem might hit some other platforms which
currently reserve a tight space of 128 bytes for the global_data
struct!
Michael Heimpold [Wed, 10 Apr 2013 10:36:19 +0000 (10:36 +0000)]
env_mmc: add support for redundant environment
This patch add support for storing the environment redundant on
mmc devices. Substantially it re-uses the logic from the NAND implementation,
that means using an incremental counter for marking newer data.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Andreas Bießmann [Thu, 18 Apr 2013 22:48:50 +0000 (22:48 +0000)]
lib: consolidate hang()
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly] Signed-off-by: Tom Rini <trini@ti.com>
part/dev_desc: Add log2 of blocksize to block_dev_desc data struct
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Bugfix:
Here at this place we need the fat size in sectors not bytes.
This was found during code review when adding support for storage
devices with blocksizes != 512.
disk/gpt: Fix GPT partition handling for blocksize != 512
Disks beyond 2T in size use blocksizes of 4096 bytes. However a lot of
code in u-boot still assumes a 512 byte blocksize.
This patch fixes the handling of GPTs.
Devices that used to have a whole disk FAT filesystem but got then
partitioned will most likely still have a FAT or FAT32 signature
in the first sector as this sector does not get overwritten by
a partitioning tool (otherwise the tool would risk to kill the mbr).
The current partition search algorithm will erronously detects such
a device as a raw FAT device.
Instead of looking for the FAT or FAT32 signatures immediately we
use the same algorithm as used by the Linux kernel and first check
for a valid boot indicator flag on each of the 4 partitions.
If the value of this flag is invalid for the first entry we then
do the raw partition check.
If the flag for any higher partition is wrong we assume the device
is neiter a MBR nor PBR device.
Simon Glass [Wed, 3 Apr 2013 08:54:30 +0000 (08:54 +0000)]
mmc: Define a constant for the maximum block size
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Wolfgang Denk [Sat, 23 Mar 2013 23:50:34 +0000 (23:50 +0000)]
setexpr: add regex substring matching and substitution
Add "setexpr name gsub r s [t]" and "setexpr name sub r s [t]"
commands which implement substring matching for the regular
expression <r> in the string <t>, and substitution of the string <s>.
The result is assigned to the environment variable <name>. If <t> is
not supplied, the previous value of <name> is used instead. "gsub"
performs global substitution, while "sub" will replace only the first
substring.
Both commands are closely modeled after the gawk functions with the
same names.
Examples:
- Generate broadcast address by substituting the last two numbers of
the IP address by "255.255":
- Depending on keyboard configuration (German vs. US keyboard) a
barcode scanner may initialize the MAC address as C0:E5:4E:02:06:DC
or as C0>E5>4E>02>06>DC. Make sure we always have a correct value:
Wolfgang Denk [Sat, 23 Mar 2013 23:50:33 +0000 (23:50 +0000)]
setexpr: simplify code, improve help message
Simplify the argument checking for the "setexpr" command. This is
done mainly to make future extensions easier.
Also improve the help message for the one argument version of the
command - this does not "load an address", but a value, which in
this context may be a plain number or a pointer dereference.
Wolfgang Denk [Sat, 23 Mar 2013 23:50:32 +0000 (23:50 +0000)]
"env grep" - add support for regular expression matches
When CONFIG_REGEX is enabled, the new option "-e" becomes available
which causes regular expression matches to be used. This allows for
example things like these:
Wolfgang Denk [Sat, 23 Mar 2013 23:50:31 +0000 (23:50 +0000)]
Add SLRE - Super Light Regular Expression library
Downloaded from http://slre.sourceforge.net/
and adapted for U-Boot environment.
Used to implement regex operations on environment variables.
Code size is ~ 3.5 KiB on PPC.
To enable this code, define the CONFIG_REGEX option in your board
config file.
Note: There are more recent versions of the SLRE library available at
http://slre.googlecode.com ; unfortunately, the new code has a heavily
reorked API which makes it less usable for our purposes:
- the return code is strings, which are more difficult to process
- we don't get any information any more which sub-string of the data
was matched by the given regex
- it is much more cumbersome to work with arbitrary expressions, where
for example the number of substrings for capturing are not known at
compile time
Also, there does not seem to be any real changes or improvements of
the functionality.
Because of this, we deliberately stick with the older code.
Note 2: the test code (built when SLRE_TEST is defined) was modified
to allow for more extensive testing; now we can test the regexp
matching on all lines on a text file (instead of the whole data in the
file as a single block).
Wolfgang Denk [Sat, 23 Mar 2013 23:50:28 +0000 (23:50 +0000)]
hashtable: preparations to use hexport_r() for "env grep"
The output of "env grep" is unsorted, and printing is done by a
private implementation to parse the hash table. We have all the
needed code in place in hexport_r() alsready, so let's use this
instead. Here we prepare the code for this, without any functional
changes yet.
Peter Korsgaard [Thu, 21 Mar 2013 04:55:17 +0000 (04:55 +0000)]
spl_mmc: cleanup variable types
block_read returns unsigned long, so it doesn't make sense to check for
< 0. and neither does marking the header structure as const and then
casting away the constness to load data into it.
Also cleanup some unneeded pointer casting while we're at it.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> Reviewed-by: Tom Rini <trini@ti.com>
Simon Glass [Sat, 20 Apr 2013 08:42:51 +0000 (08:42 +0000)]
sandbox: fs: Add support for saving files to host filesystem
This allows write of files from the host filesystem in sandbox. There is
currently no concept of overwriting the file and removing its existing
contents - all writing is done on top of what is there. This means that
writing 10 bytes to the start of a 1KB file will only update those 10
bytes, not truncate the file to 10 byte slong.
Simon Glass [Sat, 20 Apr 2013 08:42:48 +0000 (08:42 +0000)]
sandbox: Allow -c argument to provide a command list
This allows passing of entire scripts to sandbox with the -c argument,
which is useful for testing. Commands can be delimited with a newline
or semicolon.
In practice it doesn't seem like a good idea to make the the working
FDT point to the control FDT. Now that we can access the control FDT
using the 'fdt' command, there is no need for this feature. Remove it.
Simon Glass [Sat, 20 Apr 2013 08:42:43 +0000 (08:42 +0000)]
Add getenv_hex() to return an environment variable as hex
This conversion is required in a number of places in U-Boot. Add a
standard function to provide this feature, so we avoid all the different
variations in the way it is coded.
Simon Glass [Sat, 20 Apr 2013 08:42:41 +0000 (08:42 +0000)]
sandbox: Add CONFIG_OF_HOSTFILE to read FDT from host file
With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.
Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.
Simon Glass [Sat, 20 Apr 2013 08:42:37 +0000 (08:42 +0000)]
sandbox: Provide a way to map from host RAM to U-Boot RAM
In many cases, pointers to memory are passed around, and these pointers
refer to U-Boot memory, not host memory. This in itself is not a
problem.
However, in a few places, we cast that pointer back to a ulong (being
a U-Boot memory address). It is possible to convert many of these cases
to avoid this. However there are data structures (e.g. struct
bootm_headers) which use pointers. We could with a lot of effort adjust
the structs and all code that uses them to use ulong instead of pointers.
This seems like an unacceptable cost, since our objective with sandbox
is to minimise the impact on U-Boot code while maximising the features
available to sandbox.
Therefore, create a map_to_sysmem() function which converts from a
pointer to a U-Boot address. This can be used sparingly when needed.
Simon Glass [Sat, 20 Apr 2013 08:42:36 +0000 (08:42 +0000)]
Trigger generic board error only when building
At present the generic board error can occur when configuring U-Boot, or
during distclean, but this is incorrect. The existing autoconf.mk may come
from an earlier U-Boot configuration which is about to be overwritten.
Make the error conditional so that it will only be triggered when we are
actually building U-Boot.
This avoids a problem where the system is being reconfigured to remove
CONFIG_SYS_GENERIC_BOARD on an architecture that does not support it.
Currently this will print an error and require the manual removal of
include/autoconf.mk.
post: fix I2C POST failure for devices in CONFIG_SYS_POST_I2C_IGNORES
Devices in CONFIG_SYS_POST_I2C_IGNORES list may be absent
and the rule is not to report I2C POST failure for devices
in this list. Currently this doesn't work since probing for
these devices isn't done and thus they are not marked as
successfully probed. Ignore optional devices when checking
for devices that didn't respond.
Michal Simek [Wed, 7 Nov 2012 14:27:39 +0000 (15:27 +0100)]
microblaze: Disable all cpu features before reset
Fix microblaze soft reset function and disable
all cpu features. Especially disable caches because
IRQs were off by disable_interrupts().
Reported-by: John Williams <john.williams@xilinx.com> Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 2 Nov 2012 08:33:05 +0000 (09:33 +0100)]
microblaze: Fix reset function
Remove CONFIG_SYS_RESET_ADDRESS macro.
It was there from historical point of view
when soft reset was just jump to u-boot text start
(not used right now).
Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 24 Apr 2013 07:31:40 +0000 (09:31 +0200)]
git-mailrc: Add trini shortcut
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Easier for using with patman.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stefan Roese [Thu, 4 Apr 2013 13:53:14 +0000 (15:53 +0200)]
flash: Add optional verify-after-write feature
Sometimes it might make sense to verify the written data to NOR flash.
This patch adds this feature. To enable this verify-after-write, you
need to define CONFIG_FLASH_VERIFY in your board config header.
Please note that this option is useless in nearly all cases,
since such flash programming errors usually are detected earlier
while unprotecting/erasing/programming. Please only enable
this option if you really know what you are doing.
Stefan Roese [Fri, 8 Mar 2013 15:50:41 +0000 (16:50 +0100)]
ppc4xx: Add lcd4_lwmon5 support
This patch adds the fast booting LWMON5 derivat "lcd4_lwmon5".
Its a stripped down version of the full blown lwmon5 support,
without ECC, USB, POST and some other stuff. It used the newly
introduced SPL infrastrucure for SPL from NOR flash booting
on the PPC4xx.
By setting the environment variable "boot_os" to "yes", Linux
will be started from the SPL version. If not, the "normal"
U-Boot will be started.
Stefan Roese [Fri, 22 Feb 2013 10:36:50 +0000 (11:36 +0100)]
Makefile: Add target for combined u-boot.img & spl/u-boot.bin
This new make target "u-boot-img-spl-at-end.bin" consists of the
the real, full-blown U-Boot image and the U-Boot SPL binary
directly attached to it. The full-blown U-Boot image has the
mkimage header included, with its load-address and entry-point.
This will be used by the upcoming lwmon5 PPC440EPx derivate board
port.
Simon Glass [Thu, 18 Apr 2013 10:25:51 +0000 (10:25 +0000)]
crc32: Correct endianness of crc32 result
When crc32 is handled by the hash library, it requires the data to be in
big-endian format, since it reads it byte-wise. Thus at present the 'crc32'
command reports incorrect data. For example, previously we might see:
Andreas Bießmann [Mon, 15 Apr 2013 23:52:18 +0000 (23:52 +0000)]
patman: fix gitutil for decorations
The git config parameter log.decorate is quite useful when working with git.
Patman, however can not handle the decorated output when parsing the commit.
To prevent this use the '--no-decorate' switch for git-log.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 11 Mar 2013 06:30:27 +0000 (06:30 +0000)]
fdt: Ensure that libfdt_env.h comes from U-Boot
When building host utilities, we include libfdt.h from the host, not from
U-Boot. This in turn brings in libfdt_env.h from the host, which can mess
up the types and cause a build failure, depending on the host environment.
To fix this, force inclusion of U-Boot's libfdt_env.h so that the types
are correct.
Another way to fix this is to use -nostdinc and -idirafter to ensure that
system includes are included after U-Boot ones. Unfortunately this means
that U-Boot's errno.h gets included instead of the system one. This in
turn requires a hack to errno.h to redirect things, so all in all the
solution in this patch is probably cleaner.
projects / u-boot / log