Tom Rini [Tue, 8 Nov 2016 02:34:55 +0000 (21:34 -0500)]
TI: Remove CONFIG_OMAP_COMMON in favor of CONFIG_ARCH_OMAP2
With the move to arch/arm/mach-omap2 there are now very few uses of
CONFIG_OMAP_COMMON and further they can all be replaced with
CONFIG_ARCH_OMAP2, so do so.
Tom Rini [Tue, 8 Nov 2016 02:34:54 +0000 (21:34 -0500)]
arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Tom Rini [Tue, 8 Nov 2016 02:34:53 +0000 (21:34 -0500)]
arm: Introduce ARCH_OMAP2
To start consolidating various TI-related code, introduce the ARCH_OMAP2
symbol. While we have removed omap2-specific boards some time ago,
matching up with the kernel naming here will help overall.
Stefan Brüns [Sat, 5 Nov 2016 21:17:14 +0000 (22:17 +0100)]
ext4: Fix handling of sparse files
A sparse file may have regions not mapped by any extents, at the start
or at the end of the file, or anywhere between, thus not finding a
matching extent region is never an error.
Found by python filesystem tests.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Stefan Brüns [Sat, 5 Nov 2016 16:45:32 +0000 (17:45 +0100)]
test/py: expose config and log as session scoped fixture
If a test uses a fixture which is expensive to setup, the fixture can
possibly created with session or module scope. As u_boot_console has
function scope, it can not be used in this case.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Edworthy [Thu, 3 Nov 2016 11:05:12 +0000 (11:05 +0000)]
gpio: dwapb: Add support for port B
The IP supports two ports, A and B, each providing up to 32 gpios.
The driver already creates a 2nd gpio bank by reading the 2nd node
from DT, so this is quite a simple change to support the 2nd bank.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Semen Protsenko [Mon, 31 Oct 2016 17:53:46 +0000 (19:53 +0200)]
arm: dra7xx: Unify Android partition table
Make Android partition table the same as for AM57x EVM.
1. Make "bootloader" partition start from 0x300 sectors offset, so
DRA7 is bootable in Android mode (see
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR option).
2. Increase "bootloader" partition size, because size of u-boot.img is
about 632 KiB (when building DT defconfig, with FIT image enabled).
3. Specify "reserved" partition explicitly, rather than specifying
"efs" partition start. Reserved area will be used to store U-Boot
environment on eMMC. It's convenient to have it exposed explicitly
so we can read/write U-Boot environment.
4. Keep all Android partitions locations intact, by reducing
"reserved" partition size. CONFIG_ENV_SIZE is considered.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Semen Protsenko [Mon, 31 Oct 2016 17:53:38 +0000 (19:53 +0200)]
arm: am57xx: Define Android partition table
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Semen Protsenko [Mon, 24 Oct 2016 15:41:11 +0000 (18:41 +0300)]
ti_omap5_common: Respect USB controller number in fastboot
On "fastboot reboot-bootloader" we check "dofastboot" variable and do
"fastboot 0" command in U-Boot if it's 1. But there are boards which have
USB controller number other than 0, so it should be respected when
performing "fastboot" command.
This patch reuses CONFIG_FASTBOOT_USB_DEV option toprovide correct USB
controller number to "fastboot" command.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Semen Protsenko [Mon, 24 Oct 2016 15:41:10 +0000 (18:41 +0300)]
fastboot: Add CONFIG_FASTBOOT_USB_DEV option
Some boards (like AM57x EVM) has USB OTG controller other than 0. So in
order to use correct controller number in compiled environment we should
define CONFIG_FASTBOOT_USB_DEV option.
For example, when doing "fastboot reboot-bootloader" we want to enter
fastboot mode automatically. But to do so we need to provide controller
number to "fastboot" command. If this procedure is defined in some config
which is common to bunch of boards, and boards have different USB
controller numbers, we can't just hardcode "fastboot 0" in the
environment. We need to use configurable option, which this patch adds.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Fri, 14 Oct 2016 05:05:24 +0000 (10:35 +0530)]
ARM: AMx3xx: Centralize early clock initialization
This is similar to Commit 93e6253d11030 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
ti81xx] Signed-off-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Fri, 14 Oct 2016 05:05:23 +0000 (10:35 +0530)]
ARM: AMx3xx: Allow arch specific code to use early DM
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit e850ed82bce8 ("ARM: OMAP4+: Allow
arch specific code to use early DM")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 17 Nov 2016 16:46:45 +0000 (11:46 -0500)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
Alexander Graf [Thu, 17 Nov 2016 00:03:02 +0000 (01:03 +0100)]
ls2080ardb: Convert to distro boot
Most new systems in U-Boot these days make use of the generic "distro"
framework which allows a user to have U-Boot scan for a bootable OS
on all available media types.
This patch extends the LS2080ARDB board to use that framework if the
hard coded NOR flash location does not contain a bootable image.
Alexander Graf [Thu, 17 Nov 2016 00:03:00 +0000 (01:03 +0100)]
armv8: ls2080a: Declare spin tables as reserved for efi loader
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.
Alexander Graf [Thu, 17 Nov 2016 00:02:57 +0000 (01:02 +0100)]
ls2080: Exit dpaa only right before exiting U-Boot
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
Alexander Graf [Thu, 17 Nov 2016 00:02:58 +0000 (01:02 +0100)]
efi_loader: AArch64: Run EFI payloads in EL2 if U-Boot runs in EL3
Some boards decided not to run ATF or other secure firmware in EL3, so
they instead run U-Boot there. The uEFI spec doesn't know what EL3 is
though - it only knows about EL2 and EL1. So if we see that we're running
in EL3, let's get into EL2 to make payloads happy.
Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: York Sun <york.sun@nxp.com>
Maxime Ripard [Fri, 4 Nov 2016 15:18:10 +0000 (16:18 +0100)]
sunxi: sina33: Enable the eMMC
The SinA33 has an 4GB Toshiba eMMC connected to the MMC2 controller.
Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Fri, 4 Nov 2016 15:18:09 +0000 (16:18 +0100)]
mmc: sunxi: Enable 8bits bus width for sun8i
The sun8i SoCs also have a 8 bits capable MMC2 controller. Enable the
support for those too.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Fri, 4 Nov 2016 15:18:08 +0000 (16:18 +0100)]
mmc: Retry the switch command
Some eMMC will fail at the first switch, but would succeed in a subsequent
one.
Make sure we try several times to cover those cases. The number of retries
(and the behaviour) is currently what is being used in Linux.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM64: zynqmp: Adding prefetchable memory space to pcie
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
For LPDDMA channels the two clocks are missing in the
Dma node resulting probe failure.
xilinx-zynqmp-dma ffa80000.dma: main clock not found.
xilinx-zynqmp-dma ffa80000.dma: Probing channel failed
xilinx-zynqmp-dma: probe of ffa80000.dma failed with error -2
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ARM64: zynqmp: Add description for LPDDMA channel usage
LPDDMA default allows only secured access.
inorder to enable these dma channels,
one should ensure that it allows non secure access.
This patch updates the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Filip Drazic [Mon, 29 Aug 2016 17:32:59 +0000 (19:32 +0200)]
ARM64: zynqmp: Support for multiple PM IDs assigned to a PM domain
Previously, it was assumed that there is a 1:1 mapping between
PM ID defined in the platform firmware and a PM domain. However, there
can be a situation where multiple PM IDs belong to a single PM domain
(e.g. PM IDs for GPU and two pixel processors correspond to a single
PM domain).
This patch adds support for assigning more than one PM ID to
a single PM domain.
Updated documentation accordingly.
Assigned pixel processors PM IDs to GPU PM domain.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Filip Drazic [Thu, 25 Aug 2016 16:58:49 +0000 (18:58 +0200)]
ARM64: zynqmp: DT: Remove unused DDR PM domain
DDR power states are handled by the PM firmware, so this domain is
redundant. Also, since there is no device using this PM domain,
it will be powered off during boot, which is wrong.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com> Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 11 Nov 2016 12:21:04 +0000 (13:21 +0100)]
ARM64: zynqmp: Remove DTC 1.4.2 warnings
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /amba has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /amba/usb@fe200000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /amba/usb@fe300000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video2channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-graphicschannel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 11 Nov 2016 12:11:37 +0000 (13:11 +0100)]
ARM: zynq: Remove DTC 1.4.2 warnings
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 14 Jul 2016 09:13:04 +0000 (11:13 +0200)]
ARM64: zynqmp: Ignore warnings from autogenerated files
Autogenerated files contain casting issues and missing function
declaration and even usleep implementation. Suppress them for now
till these files are fixed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 25 Oct 2016 09:43:02 +0000 (11:43 +0200)]
ARM64: zynqmp: Fix secondary bootmode enabling
Do not setup use_alt bit which copy alternative boot mode to
boot mode. The reason is that this bit is cleared after POR
but not after any software reset which will cause
that after SW reset bootrom will look for different boot image.
This patch setups alternative boot mode selection (purely SW
handling) and extends code to read this alternative boot mode first and
use it if it is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
nand: arasan_nfc: Clear ecc on bit while sending read command
Clear ecc ON bit while sending read command as all types
of read command(like reading spare) doesnt need ECC to be
enabled. It has been anyway taken care in other places
whereever required using arasan_nand_enable_ecc().
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mike Looijmans [Fri, 30 Sep 2016 06:13:13 +0000 (08:13 +0200)]
ARM: zynq: Add support for the topic-miami system-on-modules and carrier boards
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.
The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.
The "Florida" carrier boards add SD, USB, ethernet and other interfaces.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 21 Oct 2016 11:16:13 +0000 (13:16 +0200)]
tools: mkimage: Check if file is regular file
Current Makefile.spl passes -R parameter which is not empty
and pointing to ./ folder.
"./tools/mkimage -T zynqmpimage -R ./"" -d spl/u-boot-spl.bin
spl/boot.bin"
That's why mkimage is trying to parse ./ file and generate
register init which is wrong.
Check that passed filename is regular file. If not do not work with it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mike Looijmans [Tue, 20 Sep 2016 09:37:24 +0000 (11:37 +0200)]
tools: mkimage: Add support for initialization table for Zynq and ZynqMP
The Zynq/ZynqMP boot.bin file contains a region for register initialization
data. Filling in proper values in this table can reduce boot time
(e.g. about 50ms faster on QSPI boot) and also reduce the size of
the SPL binary.
The table is a simple text file with register+data on each line. Other
lines are simply skipped. The file can be passed to mkimage using the
"-R" parameter.
It is recommended to add reg init file to board folder.
For example:
CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Simon Glass [Mon, 7 Nov 2016 15:47:16 +0000 (08:47 -0700)]
x86: Enable EFI loader support
Enable this so that EFI applications (notably grub) can be run under U-Boot
on x86 platforms.
At present the 'hello world' EFI application is not supported for the
qemu-x86_efi_payload64 board. That board builds a payload consisting of a
64-bit header and a 32-bit U-Boot, which is incompatible with the way the
EFI loader builds its EFI application. The following error is obtained:
x86_64-linux-ld.bfd: i386 architecture of input file
`lib/efi_loader/helloworld.o' is incompatible with i386:x86-64 output
This could be corrected with additional Makefile rules. For now, this
feature is disabled for that board.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[agraf: drop hello kconfig bits] Signed-off-by: Alexander Graf <agraf@suse.de>
Simon Glass [Mon, 7 Nov 2016 15:47:06 +0000 (08:47 -0700)]
x86: Tidy up selection of building the EFI stub
At present we use a CONFIG option in efi.h to determine whether we are
building the EFI stub or not. This means that the same header cannot be
used for EFI_LOADER support. The CONFIG option will be enabled for the
whole build, even when not building the stub.
Use a different define instead, set up just for the files that make up the
stub.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Alexander Graf <agraf@suse.de>
Emmanuel Vadot [Tue, 8 Nov 2016 05:03:29 +0000 (06:03 +0100)]
efi_loader: console: Correctly report modes
Add support for EFI console modes.
Mode 0 is always 80x25 and present by EFI specification.
Mode 1 is always 80x50 and not mandatory.
Mode 2 and above is freely usable.
If the terminal can handle mode 1, we mark it as supported.
If the terminal size is greater than mode 0 and different than mode 1,
we install it as mode 2.
Modes can be switch with cout_set_mode.
Changes in V5:
Correctly detect mode before enabling mode 2.
Changes in V4:
Reset cursor positon on mode switch
Use local variables in console query code
Changes in V3:
Valid mode are 0 to EFIMode-1
Fix style
Changes in V2:
Add mode switch
Report only the modes that we support
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com> Signed-off-by: Alexander Graf <agraf@suse.de>
efi: Use device device path type Messaging for network interface node
When adding network interface node use Messaging device path with
subtype MAC Address and device's MAC address as a value instead
of Media Device path type with subtype File Path and path "Net"
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com> Signed-off-by: Alexander Graf <agraf@suse.de>
Hans de Goede [Mon, 14 Nov 2016 11:53:25 +0000 (12:53 +0100)]
MAINTAINERS: mark sunxi status as Orphan
Ian has not had any time for sunxi for some time now and I'm
in the same situation now, so I'm stepping down as sunxi
custodian and marking the sunxi support as Orphan.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
drivers/video/video_bmp.c: In function ‘video_bmp_display’:
drivers/video/video_bmp.c:315:22: error: ‘lcd_line_length’ undeclared (first use in this function)
fb -= width * 2 + lcd_line_length;
^
This patch moves to using the correct variable instead and enables the
'bmp' command for DM again.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de>
projects / u-boot / log