Simon Glass [Tue, 23 Dec 2014 19:04:58 +0000 (12:04 -0700)]
imx: ls102xa: Remove reference to gdata
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Simon Glass [Tue, 23 Dec 2014 19:04:57 +0000 (12:04 -0700)]
imx: woodburn: Remove reference to gdata
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stefano Babic <sbabic@denx.de>
Simon Glass [Tue, 23 Dec 2014 19:04:56 +0000 (12:04 -0700)]
imx: cm_fx6: Remove reference to gdata
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Simon Glass [Tue, 23 Dec 2014 19:04:55 +0000 (12:04 -0700)]
zynq: Remove reference to gdata
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Andrew Gabbasov [Thu, 25 Dec 2014 16:22:25 +0000 (10:22 -0600)]
mmc: Skip changing bus width for MMC cards earlier than version 4.0
Wider bus widths (larger than default 1 bit) appeared in MMC standard
version 4.0. So, for MMC cards of any earlier version trying to change
the bus width (including ext_csd comparison) does not make any sense.
It may work incorrectly and at least cause unnecessary timeouts.
So, just skip the entire bus width related activity for earlier versions.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Andrew Gabbasov [Thu, 25 Dec 2014 16:22:24 +0000 (10:22 -0600)]
mmc: Avoid redundant switching to 1-bit bus width for MMC cards
If all the commands switching an MMC card to 4- or 8-bit bus width fail,
and the bus width for the controller and the driver is still set
to default 1 bit, there is no need to send one more command to switch
the card to 1-bit bus width. Also, if the card or host controller do not
support wider bus widths, there is no need to send a switch command at all.
However, if one of switch commands succeeds, but the subsequent ext_csd
fields comparison fails, the card should be switched to some other bus width
(next in the list for the loop), or to default 1-bit bus width as a last
resort. That's why it would be incorrect to just remove the 1-bit bus width
case from the list, it should still be processed in some cases.
panto: Minor cosmetic edit removing superfluous parentheses.
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:33 +0000 (10:50 +0100)]
mmc: extend mmcinfo output to show partition write reliability settings
This extends the mmcinfo hardware partition info output to show
partitions with write reliability enabled with the "WRREL" string.
If the partition does not have write reliability enabled the "WRREL"
string is omitted; this is analogous to the ehhanced attribute.
Example output:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
Erase Group Size: 8 MiB
HC WP Group Size: 16 MiB
User Capacity: 13.8 GiB ENH WRREL
User Enhanced Start: 0 Bytes
User Enhanced Size: 512 MiB
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH WRREL
GP2 Capacity: 64 MiB ENH WRREL
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:32 +0000 (10:50 +0100)]
mmc: extend the mmc hwpartition sub-command to change write reliability
This change extends the mmc hwpartition sub-command to change the
per-partition write reliability settings. It also changes the
syntax used for the enhanced user data area slightly to better
accomodate the write reliability option.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:31 +0000 (10:50 +0100)]
mmc: extend the mmc hardware partitioning API with write reliability
The eMMC partition write reliability settings are to be set while
partitioning a device, as per the eMMC spec, so changes to these
attributes needs to be done in the hardware partitioning API.
This commit adds such support.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:30 +0000 (10:50 +0100)]
mmc: add mmc hwpartition sub-command to do eMMC hardware partitioning
Adds the mmc hwpartition sub-command to perform eMMC hardware
partitioning on an mmc device. The number of arguments can be
large for a complex partitioning, but as the partitioning has
to be done in one go it is difficult to make it simpler.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:29 +0000 (10:50 +0100)]
mmc: add API to do eMMC hardware partitioning
This adds an API to do hardware partitioning on eMMC devices. The
new mmc_hwpart_config() function does the partitioning in one go.
As the different attributes and partitioning options on eMMC may
be interdependent validation has to be done based on the complete
partitioning configuration. The function accepts three modes:
- MMC_HWPART_CONF_CHECK: just validates that the configuration
is valid.
- MMC_HWPART_CONF_SET: validates and sets all the fields in
EXT_CSD but without setting the "partitioning completed" bit,
and thus is reversible.
- MMC_HWPART_CONF_COMPLETE: does everything and is thus not
reversible.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:28 +0000 (10:50 +0100)]
mmc: the ext_csd data may be used during init even if reading failed
The mmc_startup() function uses the ext_csd data even if reading it
from the mmc device failed. This bug was introduced in commit bc897b1d4d86597311430dbe7b3e6c807c8c53e5. We now bail out if
reading it fails, this should not be a problem as ext_csd was
introduced in MMC 4.0 and this code is conditional on MMC >= 4.0.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:27 +0000 (10:50 +0100)]
mmc: eMMC partitioning data is not effective till partitioning completed
The eMMC spec says that partitioning is only effective after the
PARTITION_SETTING_COMPLETED is set in EXT_CSD (and a power cycle was done,
but that we cannot know). Thus the partition sizes and attributes should
be ignored when that bit is not set, otherwise the various capacities
are not coherent (e.g., the user data capacity will be that of the
unpartitioned device while partition sizes would be non-zero).
Prescence of non-zero partitioning data is nevertheless still used to
activate the high-capacity size definitions (EXT_CSD_ERASE_GROUP_DEF)
as it is necessary to set that to write any of the partitioning fields
in EXT_CSD, so having partitioning data means someone previously
activated that and we should keep it activated.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:26 +0000 (10:50 +0100)]
mmc: show the erase group size and HC WP group size in mmcinfo output
This adds the erase group size and high-capacity WP group size to
mmcinfo's output. The erase group size is necessary to properly align
erase requests on eMMC. The high-capacity WP group size is necessary
to properly align partitions on eMMC.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:25 +0000 (10:50 +0100)]
mmc: read the high capacity WP group size for eMMC
Read the eMMC high capacity write protect group size at mmc device
initialization. This is useful to correctly partition an eMMC device,
as partitions need to be aligned to this size.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:24 +0000 (10:50 +0100)]
mmc: fix erase_grp_size computation with high-capacity size definition
The erase_grp_size in struct mmc is to be a size in 512-byte sectors
but the code used to compute it for eMMC when EXT_CSD_ERASE_GROUP_DEF is
enabled computed it as bytes, leading to erase sizes and alignment
much larger than what is actually required by the mmc device.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:20 +0000 (10:50 +0100)]
mmc: incomplete test to switch to high-capacity group size definitions
The eMMC spec mandates that the high-capacity group size definitions
should be enabled when the device is partitioned (by setting
ERASE_GROUP_DEF in EXT_CSD). The current test to determine when this is
required misses a few cases. In particular a device may have been
partitioned without setting the enhanced attribute on any partition
or partitioning may be completed without creating any extra partitions.
This change moves the code to set ERASE_GROUP_DEF to after reading
all partition information. It is also enabled when
PARTITIONING_SETTING_COMPLETED is set as it is necessary to enable
ERASE_GROUP_DEF before setting that bit, so it means that the user
previously switched to the high capacity definitions.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:18 +0000 (10:50 +0100)]
mmc: make eMMC general purpose partition numbering match spec
The eMMC spec numbers general purpose partitions starting at 1, but
the mmcinfo output follows the internal numbering which starts at 0.
Make the mmcinfo command output number partitions as in the eMMC
spec to avoid confusion.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:17 +0000 (10:50 +0100)]
mmc: extend mmcinfo to show enhanced partition attribute
This extends the mmcinfo command's output to show which eMMC partitions
have the enhanced attribute set. Note that the eMMC spec says that
if the enhanced attribute is supported then the boot and RPMB
partitions are of the enhanced type.
The output of mmcinfo becomes:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB ENH
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH
GP2 Capacity: 64 MiB ENH
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Diego Santa Cruz [Tue, 23 Dec 2014 09:50:16 +0000 (10:50 +0100)]
mmc: show hardware partition sizes in mmcinfo output
There is currently no command that will provide an overview of the hardware
partitions present on an eMMC device, one has to switch to every partition
via "mmc dev" and run mmcinfo for each to get the partition's capacity.
This commit adds a few lines of output to mmcinfo with the sizes of the
present partitions, like this:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB
Boot Capacity: 16 MiB
RPMB Capacity: 128 KiB
GP1 Capacity: 64 MiB
GP2 Capacity: 64 MiB
panto: Minor edit removing superfluous parentheses.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com> Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Hans de Goede [Sun, 11 Jan 2015 19:34:53 +0000 (20:34 +0100)]
musb-new: Add urb and hep parameters to construct_urb
Make construct_urb take an urb and hep parameter, rather then having it always
operate on the file global urb and hep structs. This is a preperation patch
for adding interrupt queue support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 11 Jan 2015 19:34:52 +0000 (20:34 +0100)]
musb-new: Properly remove a transfer from the schedule on timeout
If a transfer / urb times-out, properly remove it from the schedule, rather
then letting it sit on the ep head. This stops the musb code from getting
confused and refusing to queue further transfers after a timeout.
Tested by unplugging a usb-keyboard, replugging it and doing a usb-reset,
before this commit the keyboard would not work after the usb-reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 11 Jan 2015 19:34:51 +0000 (20:34 +0100)]
musb-new: Fix reset sequence when in host mode
This commit fixes a number of issues with the reset sequence of musb-new
in host mode:
1) Our usb device probe relies on a second device reset being done after the
first descriptors read. Factor the musb reset code into a usb_reset_root_port
function (and add this as an empty define for other controllers), and call
this when a device has no parent.
2) Just like with normal usb controllers there needs to be a delay after
reset, for normal usb controllers, this is handled in hub_port_reset, add a
delay to usb_reset_root_port.
3) Sync the musb reset sequence with the upstream kernel, clear all bits of
power except bits 4-7, and increase the time reset is asserted to 50 ms.
With these fixes an usb keyboard I have now always enumerates properly, where
as earlier it would only enumerare properly once every 5 tries.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 11 Jan 2015 19:34:50 +0000 (20:34 +0100)]
musb-new: Fix interrupt transfers not working
For bulk and ctrl transfers common/usb.c sets udev->status = USB_ST_NOT_PROC,
but it does not do so for interrupt transfers.
musb_uboot.c: submit_urb() however was waiting for USB_ST_NOT_PROC to become 0,
and thus without anyone setting USB_ST_NOT_PROC would exit immediately for
interrupt urbs, returning the urb status of EINPROGRESS as error.
This commit fixes this, thereby also making usb_kbd.c work together with
musb_new and CONFIG_SYS_USB_EVENT_POLL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 11 Jan 2015 19:34:49 +0000 (20:34 +0100)]
musb-new: Use time based timeouts rather then cpu-cycles based timeouts
CPU cycle based timeouts are no good, because how long they use depends on
CPU speed. Instead use time based timeouts, and wait one second for a
device connection to show up (per the USB spec), and wait USB_TIMEOUT_MS
for various urbs to complete.
This fixes "usb start" taking for ever when no device is plugged into the
otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 11 Jan 2015 19:34:44 +0000 (20:34 +0100)]
usb: Fix usb_kbd_deregister when console-muxing is used
When iomuxing is used we must not only deregister the device with stdio.c,
but also remove the reference to the device in the console_devices array
used by console-muxing. Add a call to iomux_doenv to usb_kbd_deregister to
update console_devices, which will drop the reference.
This fixes the console filling with "Failed to enqueue URB to controller"
messages after a "usb stop force", or when the USB keyboard is gone after a
"usb reset".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 11 Jan 2015 19:38:28 +0000 (20:38 +0100)]
usb: Add an interval parameter to create_int_queue
Currently create_int_queue is only implemented by the ehci code, and that
does not honor interrupt intervals, but other drivers which might also want
to implement create_int_queue may honor intervals, so add an interval param.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Tue, 6 Jan 2015 13:27:42 +0000 (14:27 +0100)]
config_distro_bootcmd.h: Remove unnecessary magic to avoid repeated USB scans
Now that "usb start" will only start usb if not already started, we can simply
call "usb start" whenever we (may) need access to usb devices, and it will only
actually scan the bus at the first call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Tue, 6 Jan 2015 13:27:41 +0000 (14:27 +0100)]
USB: make "usb start" start usb only once
Currently we've this magic in include/config_distro_bootcmd.h to avoid
scanning the usb bus multiple times.
And it does not work when also using an usb keyboard because then the
preboot command has already scanned the bus, so we're still scanning it
twice.
This commit makes "usb start" only start usb if it is no already started,
allowing us to remove all the magic for it from include/config_distro_bootcmd.h
and just call it unconditionally.
This also causes "usb start" and "usb reset" to actually do what their
different names suggest, rather then both of them doing exactly the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fix use-before-initialized bug in pxa25x_udc driver.
Function usb_gadget_register_driver calls udc_disable,
and udc_disable calls pullup_off that uses dev->mach->udc_command.
But dev->mach is initialized in usb_gadget_register_driver after
calling udc_disable. This patch fixes the order of initialization.
Signed-off-by: Alex Sadovsky <Nable.MainInbox@googlemail.com>
Stefan Roese [Fri, 9 Jan 2015 13:54:56 +0000 (14:54 +0100)]
usb: gadget: f_dfu: Add get_alt function to pass the USB compliance test
Without this function the USB compliance test (USB 2.0 Command Verifier) will
fail in the "Interface Descriptor Test" with this error message:
FAIL
(1.2.51) A successful GetInterface request must return the alternate setting
set by a prior call to SetInterface.
Lets add this function to read back the value so that the DFU device fully
passes the USB compliance test.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Roger Meier <r.meier@siemens.com> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Enrico Leto <enrico.leto@siemens.com> Acked-by: Heiko Schocher <hs@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
Stefan Roese [Fri, 9 Jan 2015 13:54:55 +0000 (14:54 +0100)]
usb: gadget: composite: Fix NULL pointer crash in USB compliance test
On the DXR2 board (AM335x using MUSB) the USB compliance test suite
(USB 2.0 Command Verifier) will cause the board to crash and reset
upon the "BOS Descriptor Test - Addressed state". Here the output
from the DRX2 while running this test:
By adding the case statement for USB_DT_BOS and therefore not running
into the default case (jump to unkown label) this crash is fixed.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Roger Meier <r.meier@siemens.com> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Enrico Leto <enrico.leto@siemens.com> Acked-by: Heiko Schocher <hs@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
Simon Glass [Tue, 23 Dec 2014 19:04:52 +0000 (12:04 -0700)]
sunxi: Move SPL s_init() code to board_init_f()
The current sunxi implementation uses gdata, which is going away. It also
sets up DRAM before board_init_f() in SPL.
There is really no reason to do much in s_init() since board_init_f() is
called immediately afterwards. The only change is that we need our own
implementation of board_init_f() which sets up DRAM before the BSS (which
is in DRAM) is cleared.
The s_init() code runs once for SPL and again for U-Boot proper. We
shouldn't need to init the clock/timer/gpio/i2c init twice, so just have it
in SPL.
Simon Glass [Tue, 23 Dec 2014 19:04:51 +0000 (12:04 -0700)]
arm: Add warnings about using gdata
We need to get rid of this SPL-specific setting of the global_data pointer.
It is already set up in start.S immediately before board_init_f() is called,
and there may be information there that is needed (e.g. pre-reloc malloc
info).
Tom Rini [Fri, 19 Dec 2014 21:53:24 +0000 (16:53 -0500)]
TI ARMv7: Don't use GD before crt0.S has set it
Prior to this change we set the gd pointer early so that we can store
data in it. This becomes problematic for DM changes as well as being
odd in general. Re-work the code paths so that we don't need to set the
gd pointer so early and instead can rely upon the normal setting of it.
In order to do this we do need to move certain calls from s_init into
spl_board_init(), mainly preloader_console_init and
save_omap_boot_params.
Tested on: Beaglebone Black, AM43xx GP EVM, Beagleboard, Beagleboard xM,
OMAP5 uEVM, DRA7xx EVM Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Thu, 15 Jan 2015 08:13:24 +0000 (17:13 +0900)]
powerpc: 74xx_7xx: remove 74xx_7xx cpu support
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Nye Liu <nyet@zumanetworks.com> Cc: Roy Zang <tie-fei.zang@freescale.com>
Simon Glass [Tue, 2 Dec 2014 00:34:07 +0000 (17:34 -0700)]
buildman: Add an option to write the full build output
Normally buildman runs with 'make -s' meaning that only errors and warnings
appear in the log file. Add a -V option to run make in verbose mode, and
with V=1, causing a full build log to be created.
Simon Glass [Tue, 2 Dec 2014 00:34:06 +0000 (17:34 -0700)]
buildman: Add the option to download toolchains from kernel.org
The site at https://www.kernel.org/pub/tools/crosstool/ is a convenient
repository of toolchains which can be used for U-Boot. Add a feature to
download and install a toolchain for a selected architecture automatically.
It isn't clear how long this site will stay in the current place and
format, but we should be able to rely on bug reports if it changes.
Suggested-by: Marek VaĊĦut <marex@denx.de> Suggested-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 2 Dec 2014 00:34:00 +0000 (17:34 -0700)]
buildman: Add an option to use the full tool chain path
In some cases there may be multiple toolchains with the same name in the
path. Provide an option to use the full path in the CROSS_COMPILE
environment variable.
Note: Wolfgang mentioned that this is dangerous since in some cases there
may be other tools on the path that are needed. So this is set up as an
option, not the default. I will need test confirmation (i.e. that this
commit fixes a real problem) before merging it.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Steve Rae <srae@broadcom.com>
Simon Glass [Tue, 2 Dec 2014 00:33:57 +0000 (17:33 -0700)]
buildman: Allow specifying a range of commits to build
Adjust the -b flag to permit a range expression as well as a branch.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Simon Glass [Tue, 2 Dec 2014 00:33:56 +0000 (17:33 -0700)]
buildman: Don't remove entire output directory when testing
When running tests the output directory is often wiped. This is only safe if
a branch is being built. The output directory may contain other things
besides the buildman test output.
Simon Glass [Tue, 2 Dec 2014 00:33:55 +0000 (17:33 -0700)]
buildman: Add an option to flatten output directory trees
When building current source for a single board, buildman puts the output
in <output_dir>/current/current/<board>. Add an option to make it use
<output_dir>/<board> instead. This removes the unnecessary directories
in that case, controlled by the --no-subdirs/-N option.
Suggested-by: Tom Rini <trini@ti.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 2 Dec 2014 00:33:54 +0000 (17:33 -0700)]
buildman: Try to guess the upstream commit
Buildman normally obtains the upstream commit by asking git. Provided that
the branch was created with 'git checkout -b <branch> <some_upstream>' then
this normally works.
When there is no upstream, we can try to guess one, by looking up through
the commits until we find a branch. Add a function to try this and print
a warning if buildman ends up relying on it.
Also update the documentation to match.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Wolfgang Denk <wd@denx.de>
Simon Glass [Tue, 2 Dec 2014 00:33:53 +0000 (17:33 -0700)]
buildman: Don't prune output space for 'current source' build
This is not needed since we always do a full (non-incremental) build. Also
it might be dangerous since it will try to delete everything below the
base directory.
Alexey Brodkin [Tue, 13 Jan 2015 15:49:01 +0000 (18:49 +0300)]
Kconfig: move CONFIG_SYS_CLK_FREQ to Kconfig
It makes sense to specify CONFIG_SYS_CLK_FREQ in "configs/xx_defconfig"
instead of "include/configs/xxx.h" because then header will be reusable
across boards with different CPU clocks.
Also this nice to have an ability for end user to tune this value
himself via "menuconfig".
For now I'm only applying this change to all ARC configs because
otherwise scope of change will be huge.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Hans de Goede <hdegoede@redhat.com>
cc: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
Masahiro Yamada [Thu, 8 Jan 2015 10:23:35 +0000 (19:23 +0900)]
spl: spl_nor: surround Linux-load code with #ifdef CONFIG_SPL_OS_BOOT
If CONFIG_SPL_NOR_SUPPORT is defined, spl_nor_load_image() requires
spl_start_uboot(), CONFIG_SYS_OS_BASE, CONFIG_SYS_SPL_ARGS_ADDR,
CONFIG_SYS_FDT_BASE to be defined even if users just want to run
U-Boot, not Linux. This is inconvenient.
This patch is following the codying style of common/spl/spl_nand.c.
Simon Glass [Tue, 2 Dec 2014 20:17:37 +0000 (13:17 -0700)]
bootm: Factor out common parts of image decompression code
Adjust the code so that the error reporting can all be done at the end,
and is the same for each decompression method. Try to detect when
decompression fails due to lack of space. Keep the behaviour of
resetting on failure even though there should be no memory corruption
now.
Simon Glass [Tue, 2 Dec 2014 20:17:31 +0000 (13:17 -0700)]
sandbox: Correct ordering of 'sb save' commands
Prior to commit d455d87 there was an inconsistency between the position of
the 'address' parameter in 'sb load' and 'sb save'. This was corrected but
it broke some tests. Fix the tests and also the help for 'sb save'.
Simon Glass [Tue, 2 Dec 2014 20:17:30 +0000 (13:17 -0700)]
bootm: Move compression progress/error messages into a function
This code is repeated in several places, and does not detect a common
fault where the image is too large. Move it into its own function and
provide a more helpful messages in this case, for compression schemes
which support this.
Simon Glass [Tue, 2 Dec 2014 20:17:29 +0000 (13:17 -0700)]
lzma: fix buffer bound check error further
Commit 4d3b8a0d fixed a problem with lzma decompress where it would
run out of bytes to decompress. The algorithm needs to know how many
uncompressed bytes it is expected to produce.
However, the fix introduced a potential buffer overrun, and causes
the compression test to fail (test_compression command in sandbox).
The correct fix seems to be to use the minimum of the expected number
of uncompressed bytes and the amount of output space available. That
way things work normally when there is enough space, and return an
error (without overrunning available space) when there is not.
Signed-off-by: Antonios Vamporakis <ant@area128.com> CC: Kees Cook <keescook@chromium.org> CC: Simon Glass <sjg@chromium.org> CC: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> CC: Luka Perkov <luka@openwrt.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Wed, 14 Jan 2015 03:35:24 +0000 (12:35 +0900)]
README.scrapyard: fill commit and date fields
This commit was generated by the following command:
scripts/fill_scrapyard.py
The commit-ID of CPCIISER4 removal has been fixed by hand because
the board was removed by commit 370572601027 (ppc4xx: remove CPCIISER4
board), but it was added to README.scrapyard by commit 9a4018e09a2f
(ppc4xx: remove DP405 board).
Hans de Goede [Sun, 11 Jan 2015 18:33:35 +0000 (19:33 +0100)]
sunxi: usbc: Add support for usb-vbus0 controller by axp drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
projects / u-boot / log