Simon Glass [Fri, 2 Jun 2017 01:38:58 +0000 (19:38 -0600)]
moveconfig: Support providing a path to the defconfig files
It is convenient to provide the full patch to the defconfig files in some
situations, e.g. when the file was generated by a shell command (e.g.
'ls configs/zynq*').
Add support for this, and move the globbing code into a function with its
own documentation.
Simon Glass [Mon, 24 Apr 2017 02:10:45 +0000 (20:10 -0600)]
dm: core: Add uclass_first/next_device_check()
Sometimes it is useful to iterate through all devices in a uclass and
skip over those which do not work correctly (e.g fail to probe). Add two
new functions to provide this feature.
The caller must check the return value each time to make sure that the
device is valid. But the device pointer is always returned.
mtd: stm32: use parameter instead of default value
To set wait state, a hard coded value is used instead of using
latency parameter. stm32_flash_latency_cfg() is currently used
in arch/arm/mach-stm32/stm32f4/clock.c and in
drivers/clk/clk_stm32f7.c with, in both case, "5" as parameter.
Andrew F. Davis [Thu, 29 Jun 2017 13:38:25 +0000 (08:38 -0500)]
arm: mach-keystone: Modify secure image size before copy
The size of the secure image does not include the size of the
header, subtract this out before we move the image or we grab
extra data after the image.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 27 Jun 2017 08:20:56 +0000 (13:50 +0530)]
arm: omap: Detect boot mode very early
ROM stores the boot params information in a known location
and passes it to SPL. This information needs to be copied
very early during boot or else there is a chance of getting
corrupted by SPL. So move this boot device detection very early
during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
set_state_ops is kept under PINCTRL_FULL flag in order
to decrease memory footprint in some configuration.
PINCTRL_FULL can be enabled for debug purpose.
ARM: k2g: Add K2G ICE DTB to the list of possible DTBs
K2G ICE evm will have its own dtb. Therefore, add it to the list of dtbs
located in the appended U-boot dtb FIT image. Therefore, when swapping out
dtbs K2G ICE boards can grab the correct one.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 2)
Further debugging showed that this was due to the memory node added by
default to skeleton.dtsi which was being included in keystone-k2g.dtsi.
Adding a missing node was all that was needed to remove this deprecated
dtsi file from the SoC dtsi. With skeleton.dtsi removed the dtc compiler
no longer complained about including the unit address for the memory node.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: k2g: Use board detection to wrap K2G GP specific calls
Certain peripherals used by K2G GP aren't used on K2G ICE evm. Or
configuration is slightly different. Therefore, use board detection to
deal with these variations.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Add basic pinmux data for new K2G ICE evm. Also add pinmuxing for a
generic K2G evm which includes I2C 0 and 1 used for board detection
purposes.
Since multiple K2G boards are supported that means initially generic
pinmuxing should be used when board detection hasn't ran. Once board
detection runs the proper pinmuxing can be reran to match the board
being ran on.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ks2_evm: Add EEPROM based board detection helper functions
Add a function that can be used to determine if the board being ran on is
a K2G Industrial Communication Engine EVM or K2G General Purpose EVM based
on values programmed on the EEPROM.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: k2g: Program DDRPHY_DATX8 registers via mask and value variables
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: k2g: Program DDR PHY MR2 register with the default value
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: keystone2: Add additional fields used for DDR3 configuration
Future boards will need to configure DDR3 registers in a slightly
different manner. Support this by defining additional variables and
defines that will be utilized later.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Some K2G evms have their EEPROM programming while most do not. Therefore,
add EEPROM board detection to be used as the default method and fall back
to the alternative board detection when needed.
Also reorder board configuration. Perform bare minimal configuration
initially since board detection hasn't ran. Finish board configuration
once the board has been identified.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: keystone2: Define board_fit_config_name_match for Keystone 2 boards
Now with support for U-boot runtime dtb selection each board needs to
define board_fit_config_name_match so U-boot can determine what the
correct dtb is within the FIT blob.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: k2g: Define embedded_dtb_select for runtime DTB selection in U-boot
For K2G, runtime DTB selection utilizes the embedded_dtb_select function.
Therefore, define the function which will perform a EEPROM read and then
retries selecting the correct dtb now that it can detect which board its
on. For other Keystone devices use an empty function since they will still
use the embedded FIT functionality but their FIT will only contain a single
dtb.
Most production K2G boards do not have their EEPROM programmed. Therefore,
perform a test to verify a K2G GP is currently being used and if it is then
set the values normally set by a EEPROM read.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: keystone2: Allow to build with all image formats
u-boot.bin is a copy of:
u-boot-fit-dtb.bin if CONFIG_FIT_EMBED is enabled,
u-boot-dtb.bin if CONFIG_OF_SEPARATE is enabled,
u-boot-nodtb.bin if DT is not enabled.
So, use u-boot.bin to to generate keystone images instead of
u-boot-dtb.bin
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
board_f: Add new function to allow runtime DTB selection
Runtime U-boot dtb selection is generally a two step process. First step
is to simply use an initial generic dtb. The second step is to select
the dtb and perhaps execute additional code ones U-boot knows what board
it is running on. Embedded_dtb_select handles the second step by allowing
board specific code to run and perform what ever necessary configuration
that is needed.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
arm: dts: Add new "generic" 66AK2Gx device tree file.
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: dts: k2g: Introduce U-boot specific dtsi file
Introduce K2G evm specific dtsi file for U-boot specific configurations.
This will help seperate U-boot only configurations thus making it easier to
keep device tree files synced between U-boot and Linux.
For now only add nodes to allow i2c drivers to be probed early during
the boot process.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
OF_LIST will be useable by SPL and U-boot. Therefore, update its
dependency to allow it to be enable by either SPL or U-boot specific
config option.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Andrew F. Davis <afd@ti.com>
ti: common: board_detect: Add function to determine if EEPROM was read
When the EEPROM is first read its contents are stored in memory as a
cache to avoid further I2C operations. To determine if the EEPROM was
previously read the easiest way is to check the memory to see if the
EEPROM's magic header value is set. Create a new function that can
determine if the EEPROM was previously read or not without having to
perform a I2C transaction.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
fdt: Enable selecting correct DTB from appended FIT Image
This patch gives U-boot the runtime support to have the board specific
code decide which FDT to use. This is especially useful for devices
that need this type of runtime determination and also doesn't use SPL.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
spl: fit: Break out some functions into a common file
Some of the functions within spl_fit will be used for non spl purposes.
Instead of duplicating functions simply break the functions to be reused
into its own file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Only add the new define to image.h, otherwise we see breakage
due to massive include leakage into host tools in some cases] Signed-off-by: Tom Rini <trini@konsulko.com>
In some situations the EEPROM used for board detection may not be
programmed or simply programmed incorrectly. Therefore, it may be
necessary to "simulate" reading the contents of the EEPROM to set
appropriate variables used in the board detection code.
This may also be helpful in certain boot modes where doing i2c reads
may be costly and the config supports running only a specific board.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Franklin S Cooper Jr. <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: dts: keystone-k2e-evm: Add U-boot specific dtsi file
With Davinci I2C switching to device model, K2E requires U-boot specific
device tree entries. This is only required for I2C 1 which is needed
extremely early during the boot process.
Fixes: 1743d040b1df ("ARM: keystone: Enable DM_I2C by default") Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
If the value of either "nand options" or "bbt options" has a zero in
the most significant nibble, the '0x' prefix will be isolated from the
value like shown below:
|Device 0: nand0, sector size 128 KiB
| Page size 2048 b
| OOB size 64 b
| Erase size 131072 b
| subpagesize 2048 b
| options 0x40000200
| bbt options 0x 60000
Change the format string to produce leading zeroes filling the gap.
Simon Glass [Mon, 10 Jul 2017 03:30:17 +0000 (21:30 -0600)]
libfdt: Drop -FDT_ERR_TOODEEP
This error code has not been upstreamed and is not really needed since it
is unlikely to be triggered. Drop it to maintain compatability with
upstream.
Reported-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com>
powerpc, 8xx: Properly set CPM frequency in the device tree
For processors whose core runs at twice the bus frequency,
the fallback frequency calculation in Linux provides a wrong
result. Therefore, U-boot needs to pass the correct value.
CS Systemes d'Information (CSSI) manufactures 8xx boards for
critical communication systems. Those boards have been
running U-Boot since 2010 and will have to be maintained
until at least 2027.
This commit partially restores support for the 8xx, with the
following limitations:
- Restores support for MPC866 and MPC885 only
- Does not restore IDE, PCMCIA, I2C, USB
- Does not restore examples
- Does not restore POST
- Does not restore Ethernet on SCC
- Does not restore console on SCC
- Does not restore bedbug and kgdb support
As the 866 and 885 do not support the following features,
they are not restored either:
- VIDEO / LCD
- RTC clock
The CPM uCODE patch is not restored either, because:
- 866 and 885 already have support for I2C and SPI relocation
without a uCODE patch
- relocation of SMC, I2C or SPI is only needed for using SCCs
for Ethernet or QMC
The dynamic setup/calculation of clocks is removed, we
expect the target being use with the clock and PLPRCR register
defined in the configuration.
All the clock settings for 8xx prior to 866 is removed as
well as we now only support 866 and 885.
This code is mature and addresses mature boards. Therefore
all code enclosed in '#if 0/#endif' and '#if XX_DEBUG/#endif'
is unneeded.
The following files are not restored by this patch:
Some of the restored files are not located in a proper location.
In order to keep traceability of the changes, they will be
moved to their correct location and moved to Kconfig in a
followup patch.
This patch also declares CSSI as point of contact for the update
of the 8xx platform, as those boards are the only ones still
being maintained on the 8xx area. A later patch will add
those boards to the tree.
On startup the SL50 board halt at U-Boot prompt. Use CONFIG_AUTOBOOT_KEYED
to enable autoboot for this board and define the <SPACE> key to get the
U-Boot prompt.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Andy Shevchenko [Wed, 5 Jul 2017 13:25:22 +0000 (16:25 +0300)]
avr32: Retire AVR32 for good
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Simon Glass [Sat, 1 Jul 2017 17:06:09 +0000 (11:06 -0600)]
stm32: Correct positioning of declaration
The current code gives a warning:
arch/arm/mach-stm32/stm32f7/soc.c: In function 'arch_cpu_init':
arch/arm/mach-stm32/stm32f7/soc.c:38:2: error: 'for' loop initial
declarations are only allowed in C99 or C11 mode
for (int i = 0; i < ARRAY_SIZE(stm32_region_config); i++)
^
arch/arm/mach-stm32/stm32f7/soc.c:38:2: note: use option -std=c99,
-std=gnu99, -std=c11 or -std=gnu11 to compile your code
Fix it by moving the declaration to the top of the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-cc trini
The Odroid C2 comes with several expansion options such as an RTC module.
As these expansions are not considered in the Linux device tree they have
to be enabled via device tree overlays.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Baruch Siach [Thu, 29 Jun 2017 17:37:08 +0000 (20:37 +0300)]
mkimage: fix display of image types list
Since commit 5b9d44df2307f (mkimage: Display a better list of available image
types) mkimage usage text suggest to "use -T to see a list of available image
types". Unfortunately, commit 02221f29deb8 (mkimage: Convert to use getopt())
broke that feature, because getopt() fails when -T has no option argument.
Add a pseudo image type name 'list' that lists all image types. Update the
usage text accordingly.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Peter Robinson [Mon, 26 Jun 2017 13:25:06 +0000 (14:25 +0100)]
CHIP: add device tree overlay support
CHIP and CHIP Pro devices have options of DIP addon boards some of which need
overlays from the beginning so it makes sense to enable device tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Peter Robinson [Mon, 26 Jun 2017 13:25:05 +0000 (14:25 +0100)]
96boards: dragonboard/hikey: add device tree overlay support
96boards CE devices such as the DragonBoard and Hikey devices have numerous
mezzanine options some of which need overlays from the beginning so it makes
sense to enable device tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Peter Robinson [Mon, 26 Jun 2017 13:25:04 +0000 (14:25 +0100)]
am335x: beagle/evm: add device tree overlay support
TI am33xx devices such as the BeagleBone devices have numerous cape options such
as screens some of which need overlays from the beginning so it makes sense to
enable evice tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Peter Robinson [Mon, 26 Jun 2017 13:25:03 +0000 (14:25 +0100)]
Raspberry Pi: add device tree overlay support
Raspberry Pi has numerous HAT and other HW expansion options such as screens and
cameras some of which need overlays from the beginning so it makes sense to
enable evice tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
UEFI spec 2.7 indicates that HandleProtocol can be implemented
by calling OpenProtocol with
attributes = EFI_OPEN_PROTOCOL_BY_HANDLE_PROTOCOL.
Currently we pass attributes = 0 to efi_open_protocol. 0 is not a
valid value when calling OpenProtocol. This does not cause any errors
yet because our implementation of OpenProtocol is incomplete.
We should pass the correct value to enable a fully compliant
implementation of OpenProtocol in the future.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Heiko Schocher [Tue, 27 Jun 2017 14:49:14 +0000 (16:49 +0200)]
powerpc: remove 4xx support
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Jonathan Gray [Sun, 12 Mar 2017 08:26:07 +0000 (19:26 +1100)]
efi_loader: check CreateEvent() parameters
Add some of the invalid parameter checks described in the UEFI
specification for CreateEvent(). This does not include checking
the validity of the type and tpl parameters.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au> Acked-By: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix checkpatch.pl indent warning] Signed-off-by: Alexander Graf <agraf@suse.de>
Jonathan Gray [Sun, 12 Mar 2017 08:26:06 +0000 (19:26 +1100)]
efi_loader: run CreateEvent() notify function based on flags
The UEFI specification states that the tpl, function and context
arguments are to be ignored if neither EVT_NOTIFY_WAIT or
EVT_NOTIFY_SIGNAL are specified. This matches observed behaviour with
an AMI EDK2 based UEFI implementation.
Skip calling the notify function if neither flag is present.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au> Acked-By: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 3 Jul 2017 11:32:35 +0000 (13:32 +0200)]
efi_loader: Add check for fallback fdt memory reservation
When running bootefi, we allocate new space but never check whether
the allocation succeeded. This patch adds a check so that in case
things go wrong, we at least know they did.
Christophe Leroy [Tue, 27 Jun 2017 14:00:24 +0000 (16:00 +0200)]
doc: restore doc/README.fsl-clk
doc/README.fsl-clk was removed in commit 5b8e76c35ec31 ("powerpc, 8xx: remove support for 8xx")
allthought CONFIG_SYS_FSL_CLK is defined in
arch/arm/cpu/armv8/fsl-layerscape/Kconfig and still in use
in the following configs:
projects / u-boot / log