Wu, Josh [Fri, 23 Aug 2013 07:09:05 +0000 (15:09 +0800)]
mtd: atmel_nand: pmecc: fix bug fail to correct bit error in 1024-bytes sector
The PMECC use BCH algorithm to correct error. In BCH algorithm, the
primitive polynomial value is GF(2^13) for 512-bytes sector size. And it is
GF(2^14) for 1024-bytes sector size.
This patch will choose correct degree of the remainders (13 or 14) for
different sector size.
Tested in AT91SAM9X5-EK with MLC nand flash.
More detail can be refered to section 5.4.1 of:
AT91SAM ARM-based Embedded MPU Application Note
<http://www.atmel.com/Images/doc11127.pdf>
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tom Rini [Tue, 27 Aug 2013 14:56:18 +0000 (10:56 -0400)]
omap5: Correct include order, drop CONFIG_SYS_PROMPT define
With the new include structure for TI platforms, we need to not define
our own CONFIG_SYS_PROMPT and also need to include
<configs/omap5_common.h> much sooner, so do both of these. Also drop
the unused CONFIG_NET_MULTI
Jim Lin [Mon, 26 Aug 2013 12:21:09 +0000 (20:21 +0800)]
console: usb: kbd: To fix slow TFTP booting
TFTP booting is slow when a USB keyboard is installed and
stdin has usbkbd added.
This fix is to change Ctrl-C polling for USB keyboard to every second
when NET transfer is running.
My previous patch is expected to be put into usb_kbd_testc(). But it went
into usb_kbd_getc() after applied.
This patch is to put change in correct place.
Jim Lin [Tue, 13 Aug 2013 11:04:22 +0000 (19:04 +0800)]
console: usb: kbd: To improve TFTP booting performance
TFTP booting is slow when a USB keyboard is installed and
stdin has usbkbd added.
This fix is to change Ctrl-C polling for USB keyboard to every second
when NET transfer is running.
Lukasz Majewski [Mon, 19 Aug 2013 15:17:18 +0000 (17:17 +0200)]
usb:dfu:g_dnl: Change number of exported configurations at composite gadget
USB composite gadget (g_dnl) supports only one configuration. Due to that
the corresponding field - bConfigurationValue has been changed.
Moreover more descriptive names were chosen for relevant fields.
Windows XP setup:
- Thesyscon USB Descriptor Dumper
- zadig_xp program for WinUSB installation (which is required by dfu-util)
- dfu-util for windows (version 0.6)
- TRATS target connected via USB hub to test Win XP machine.
dfu, nand, ubi: add partubi alt settings for updating ubi partition
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Tom Rini <trini@ti.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Scott Wood <scottwood@freescale.com>
Julius Werner [Fri, 19 Jul 2013 20:12:08 +0000 (13:12 -0700)]
usb: Use well-known descriptor sizes when parsing configuration
The existing USB configuration parsing code relies on the descriptors'
own length values when reading through the configuration blob. Since the
size of those descriptors is always well-defined, we should rather use
the known sizes instead of trusting device-provided values to be
correct. Also adds some safety to potential out-of-order descriptors.
Change-Id: I16f69dfdd6793aa0fe930b5148d4521f3e5c3090 Signed-off-by: Julius Werner <jwerner@chromium.org>
Phil Sutter [Fri, 19 Jul 2013 10:20:26 +0000 (12:20 +0200)]
env_nand.c: support falling back to redundant env when writing
Without this patch, when the currently chosen environment to be written
has bad blocks, saveenv fails completely. Instead, when there is
redundant environment fall back to the other copy. Environment reading
needs no adjustment, as the fallback logic for incomplete writes applies
to this case as well.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
If datbuf = memalign(ARCH_DMA_MINALIGN, nand->writesize);
succeeds and
oobbuf = memalign(ARCH_DMA_MINALIGN, nand->oobsize);
fails, nand_dump function should free databuf.
- fix adresses in env settings in config header
- add missing CONFIG_STANDALONE_LOAD_ADDR to eb_cpux9k2 config header
- remove jffs2 support, board doesn't use this anymore
- add ubifs support
- change sizes and start for partitions
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 9 Aug 2013 07:43:09 +0000 (15:43 +0800)]
arm: sama5d3: fix smc cs related registers offset
the smc cs related registers start at 0x600 and loop with 5 registers
so the reserved register should be in at91_smc structure while no in
at91_cs structure. So fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
ARM: at91: atmel_nand: add code to check the ONFI parameter ECC requirement
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's
ecc minimum requirement in ONFI parameter.
a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it.
Driver will display a WARNING if the values are different from ONFI
parameters.
b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use
the value from ONFI parameters.
* If ONFI ECC parameters are in ONFI extended parameter page, since we
are not support it, so assume the minimum ecc requirement is 2 bits
in 512 bytes.
* For non-ONFI support nand flash, also assume the minimum ecc
requirement is 2 bits in 512 bytes.
2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP
and CONFIG_PMECC_SECTOR_SIZE.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
linux/compat.h: move dev_err, dev_info and dev_dbg from usb driver to compat.h
Since kernel code current use many dev_xxx() instead of using printk. To
compatible, move those dev_xxx from usb driver to linux/compat.h. Then all
driver code can use dev_err, dev_info and dev_vdbg.
This patch also removed duplicated macro definitions in usb driver.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
ARM: at91: atmel_nand: pmecc driver will select the galois table by sector size
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 26 Jun 2013 02:48:53 +0000 (10:48 +0800)]
arm: atmel: add nand trimffs subcommand for at91sam9n12 and at91sam9x5
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot
to flash the rootfs, in order to avoid flash one sector with all 0xff
into NAND, so use nand trimffs subcommand to avoid it
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Mon, 19 Aug 2013 02:35:47 +0000 (10:35 +0800)]
net: macb: fix the following building warning
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Shaohui Xie [Mon, 19 Aug 2013 10:58:52 +0000 (18:58 +0800)]
powerpc/t4240: add QSGMII interface support
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Mon, 19 Aug 2013 10:43:07 +0000 (18:43 +0800)]
powerpc/common/vsc3316: remove const from vsc3316_config parameter define
Since the parameters need to be modified according to different Serdes
protocols at runtime, the const will block this. Also remove const from
arrays define used by vsc3316_config.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Shruti Kanetkar [Thu, 15 Aug 2013 16:25:38 +0000 (11:25 -0500)]
powerpcv2: Print hardcoded size like print_size() does
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com>
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:15 +0000 (15:16 +0800)]
TPL : introduce the TPL based on the SPL
Due to the nand SPL on some board(e.g. P1022DS)has a size limit, it can
not be more than 4K. So, the SPL cannot initialize the DDR with the SPD
code. This patch introduces TPL to enable a loader stub that is loaded
by the code from the SPL. It initializes the DDR with the SPD or other
operations.
The TPL's size is sizeable, the maximum size is decided by the memory's
size that TPL runs. It initializes the DDR through SPD code, and copys
final uboot image to DDR. So there are three stage uboot images:
* spl_boot, * tpl_boot, * final uboot image
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:13 +0000 (15:16 +0800)]
powerpc : spi flash : Support to start from eSPI with SPL
This patch introduces SPL to enable a loader stub that being loaded by
the code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:11 +0000 (15:16 +0800)]
powerpc: mpc85xx: Support booting from SD Card with SPL
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:10 +0000 (15:16 +0800)]
powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some functionality for common SPL
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Łukasz Majewski [Fri, 16 Aug 2013 13:33:33 +0000 (15:33 +0200)]
i2c:samsung: Adjust Trats, GONI and Universal_c210 boards to work with new I2C framework
New I2C framework, introduced after v2013.07 final release, imposed I2C
code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210.
Those boards were using schematic based I2C enumeration (I2C_5, I2C_9).
However, new I2C framework imposes usage of logical I2C adapters numbering
(e.g. I2C_0, I2C_1, etc).
Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions.
Trats board gained definition of second soft I2C adapter.
Chunhe Lan [Fri, 16 Aug 2013 07:10:37 +0000 (15:10 +0800)]
fsl_i2c: add workaround for the erratum I2C A004447
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Heiko Schocher <hs@denx.de>
Disabling the data cache is no longer required to boot Dalmore, so
enable it. This results in notably better performance when loading
and booting the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently all Tegra SoCs are assumed to have 32 byte cache lines. This
isn't true for Tegra114, however, which uses 4 Cortex-A15 cores and
therefore uses a cache line size of 64 bytes. Move the cache line size
setting to the per-SoC common configuration file.
Signed-off-by: Thierry Reding <treding@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Joel Fernandes [Mon, 19 Aug 2013 08:14:14 +0000 (16:14 +0800)]
SPL: Makefile: Build a separate autoconf.mk for SPL
SPL defines CONFIG_SPL_BUILD but this does not percolate to the
autoconf.mk Makefile. As a result the build breaks when
CONFIG_SPL_BUILD is used in the board-specific include header file. With
this, there is a possibility of having a CONFIG option defined in the
header file but not defined in the Makefile causing all kinds of build
failure and problems.
It also messes things for up, for example, when one might want to
undefine options to keep the SPL small and doesn't want to be stuck with
the CONFIG options used for U-boot. Lastly, this also avoids defining
special CONFIG_SPL_ variables for cases where some options are required
in U-boot but not in SPL.
We add a spl-autoconf.mk rule that is generated for SPL with the
CONFIG_SPL_BUILD flag and conditionally include it for SPL builds.
Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Ying Zhang <b40530@freescale.com>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:46 +0000 (22:12 +0200)]
board/esd/cpci750/mv_eth.c: Fix license
The file header indicated that this file was GPL-2.0+, but actually
the code was derived from (Marvell based) Linux source code which is
only GPL-2.0. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Acked-by: Stefan Roese <sr@denx.de>
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:44 +0000 (22:12 +0200)]
SPDX-License-Identifier: fixing some problematic GPL-2.0 files
Unlike the other patches in this series so far, this commit fixes a
ambiguity in the license terms for some OMAP files: the code was
originally derived from the Linux kernel sources, where it was clearly
marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot
version had a GPL-2.0+ file header added, apparently without
permission / relicensing from the original authors of the code.
Insert a GPL-2.0 SPDX-License-Identifier to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Tom Rix <Tom.Rix@windriver.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Tom Rini <trini@ti.com>
net: phy/realtek: Add support for RTL8211DN and RTL8211E phy modules
This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.
To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Axel Lin [Wed, 3 Jul 2013 03:24:18 +0000 (11:24 +0800)]
net: Use ARRAY_SIZE at appropriate places
Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Marek Vasut <marex@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Cc: Wolfgang Denk <wd@denx.de> Cc: York Sun <yorksun@freescale.com>
Dirk Eibach [Fri, 9 Aug 2013 08:52:53 +0000 (10:52 +0200)]
powerpc/ppc4xx: Do full iocon PHY initialization in software
Up to this point some PHY initialization was done from the FPGA
and some from u-boot.
From now all initialization is done from u-boot.
To keep this maintainable a PHY setup machine was implemented that can
execute commands from initialization arrays.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot / log