]> git.sur5r.net Git - u-boot/log
u-boot
6 years agoserial_bcm283x_mu: Flush RX queue after setting baud rate
Alexander Graf [Wed, 7 Mar 2018 21:08:24 +0000 (22:08 +0100)]
serial_bcm283x_mu: Flush RX queue after setting baud rate

After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.

So let's flush the RX queue whenever we initialize baud rates.

This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt.

Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
6 years agoARM: Drop unreferenced CONFIG_* defines named after boards
Tuomas Tynkkynen [Mon, 5 Mar 2018 23:46:39 +0000 (01:46 +0200)]
ARM: Drop unreferenced CONFIG_* defines named after boards

The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_AT91SAM9263EK
CONFIG_AT91SAM9RLEK
CONFIG_BARIX_IPAM390
CONFIG_BOARD_H2200
CONFIG_EP9301
CONFIG_KZM_A9_GT
CONFIG_PICOSAM
CONFIG_PLATINUM_PICON
CONFIG_PLATINUM_TITANIUM
CONFIG_PM9261
CONFIG_PM9263
CONFIG_PM9G45
CONFIG_SIEMENS_DRACO
CONFIG_SIEMENS_PXM2
CONFIG_SIEMENS_RUT
CONFIG_SMDKC100
CONFIG_SMDKV310
CONFIG_STM32F4DISCOVERY

Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
6 years agoARM: Drop unreferenced CONFIG_* defines named after SoCs
Tuomas Tynkkynen [Mon, 5 Mar 2018 23:46:38 +0000 (01:46 +0200)]
ARM: Drop unreferenced CONFIG_* defines named after SoCs

The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_ARM926EJS
CONFIG_CPUAT91
CONFIG_EXYNOS5800
CONFIG_SYS_CORTEX_R4

Most of them are config symbols named after the respective SoCs which
seems to have been a standard practice at some point.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
6 years agoMIPS: Drop unreferenced CONFIG_* defines
Tuomas Tynkkynen [Mon, 5 Mar 2018 23:46:37 +0000 (01:46 +0200)]
MIPS: Drop unreferenced CONFIG_* defines

The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_DBAU1X00
CONFIG_PB1X00

Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
6 years agotreewide: Fix gdsys mail addresses
Mario Six [Tue, 6 Mar 2018 07:04:58 +0000 (08:04 +0100)]
treewide: Fix gdsys mail addresses

The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.

Also, Dirk's address was wrong in one place; fix that as well.

Signed-off-by: Mario Six <six@gdsys.cc>
6 years agoARM: qemu-arm: Increase CONFIG_SYS_CBSIZE
Tuomas Tynkkynen [Mon, 5 Mar 2018 21:20:41 +0000 (23:20 +0200)]
ARM: qemu-arm: Increase CONFIG_SYS_CBSIZE

CONFIG_SYS_CBSIZE determines the maximum length of the kernel command
line, and the default value of 256 is too small for booting some Linux
images in the wild.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
6 years agoPrepare v2018.03-rc4 v2018.03-rc4
Tom Rini [Tue, 6 Mar 2018 01:27:08 +0000 (20:27 -0500)]
Prepare v2018.03-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoMerge git://git.denx.de/u-boot-sh
Tom Rini [Tue, 6 Mar 2018 01:24:17 +0000 (20:24 -0500)]
Merge git://git.denx.de/u-boot-sh

6 years agoDevboards.de DBM-SoC1 BOARD: Add S line
Tom Rini [Mon, 5 Mar 2018 15:20:46 +0000 (10:20 -0500)]
Devboards.de DBM-SoC1 BOARD: Add S line

This was missing the 'S' line causing a warning from genboardscfg.py

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoARM: DTS: Re-sync logicpd-som-lv with Linux 4.16-rc3
Adam Ford [Mon, 5 Mar 2018 10:16:33 +0000 (04:16 -0600)]
ARM: DTS: Re-sync logicpd-som-lv with Linux 4.16-rc3

This should clean up a warning about a missing phy-cells

Signed-off-by: Adam Ford <aford173@gmail.com>
6 years agoMAINTAINERS: bring sections into alphabetic order
Heinrich Schuchardt [Mon, 5 Mar 2018 07:15:51 +0000 (08:15 +0100)]
MAINTAINERS: bring sections into alphabetic order

POWER should be after ONENAND

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
6 years agoscripts/spelling.txt: Sync script with kernel 4.16-rc4
Fabio Estevam [Mon, 5 Mar 2018 01:55:19 +0000 (22:55 -0300)]
scripts/spelling.txt: Sync script with kernel 4.16-rc4

Keep spelling.txt in sync with the version from kernel 4.16-rc4.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
6 years agoomap3_logic: Remove unnecessary undefs
Adam Ford [Sun, 4 Mar 2018 21:05:38 +0000 (15:05 -0600)]
omap3_logic: Remove unnecessary undefs

Due to evolution of the MMC driver and better support, let's
remove unnecessary undefs.

Signed-off-by: Adam Ford <aford173@gmail.com>
6 years agoti_armv7_omap: Remove comment remnant
Adam Ford [Sun, 4 Mar 2018 20:54:15 +0000 (14:54 -0600)]
ti_armv7_omap: Remove comment remnant

With the migration to Kconfig, the I2C block no longer exists in here.
Let's clean up the comment.

Signed-off-by: Adam Ford <aford173@gmail.com>
6 years agoMPC8315ERDB: Enable DHCP support
Ed Bartosh [Sun, 4 Mar 2018 18:17:52 +0000 (19:17 +0100)]
MPC8315ERDB: Enable DHCP support

Enable DHCP support for this board.

Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agolibfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Masahiro Yamada [Sun, 4 Mar 2018 16:20:11 +0000 (01:20 +0900)]
libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>

Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agotools: Include U-Boot libfdt headers from their actual path
Paul Kocialkowski [Fri, 2 Mar 2018 22:13:42 +0000 (23:13 +0100)]
tools: Include U-Boot libfdt headers from their actual path

There are no headers for libfdt in lib/libfdt, as they are instead
located in scripts/dtc/libfdt. Specifying lib/libfdt for headers
inclusion in host tools results in using the system libfdt headers,
which is not what we want. Change this to the proper path.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
6 years agoinput: indicate that code page 437 is used
Heinrich Schuchardt [Fri, 2 Mar 2018 20:11:35 +0000 (21:11 +0100)]
input: indicate that code page 437 is used

Add a comment indicating that the German key map assumes code page 437.

Add support for character ² (square sign) in the German key map.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
6 years agopinctrl: Kconfig: Fix typo
Marek Behún [Fri, 2 Mar 2018 08:56:00 +0000 (09:56 +0100)]
pinctrl: Kconfig: Fix typo

Signed-off-by: Marek Behun <marek.behun@nic.cz>
6 years agogpio: pca953x_gpio: Support label setting from DT
Mario Six [Thu, 1 Mar 2018 13:45:04 +0000 (14:45 +0100)]
gpio: pca953x_gpio: Support label setting from DT

The PCA953x driver uses "gpio@%x_" as the GPIO bank name, where "%x" is
instantiated with the I2C address of the chip. While this works, it
becomes very confusing if a board has multiple PCAs with the same
address on different I2C busses, and it also becomes an issue when a
GPIO's value is to be set via the 'gpio' command, because this command
only ever sets the value of the first device it encounters, leaving the
other devices inaccessible to the command.

As to not break boards that rely on this naming scheme, we introduce a
new device tree string property "label" for the driver. If it exists, it
is used to build a bank name of the form "%s@%x_" (where %x is still
instantiated with the I2C address). If it does not exist, the legacy
labeling scheme is used.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
6 years agospl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the U-boot...
Faiz Abbas [Fri, 16 Feb 2018 15:47:44 +0000 (21:17 +0530)]
spl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the U-boot CONFIG

Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.

This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
6 years agotools/env: allow equal sign as key value separation
Stefan Agner [Thu, 1 Mar 2018 13:06:32 +0000 (14:06 +0100)]
tools/env: allow equal sign as key value separation

Treat the first equal sign as a key/value separation too. This makes
the script files compatible with mkenvimage input file format. It
won't support variables with equal signs anymore, but this seems not
really like a loss.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
6 years agoAtmel TPM: Fix potential buffer overruns
Jeremy Boone [Mon, 12 Feb 2018 22:56:37 +0000 (17:56 -0500)]
Atmel TPM: Fix potential buffer overruns

Ensure that the Atmel TPM driver performs sufficient
validation of the length returned in the TPM response header.
This patch prevents memory corruption if the header contains a
length value that is larger than the destination buffer.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
6 years agoInfineon TPM: Fix potential buffer overruns
Jeremy Boone [Mon, 12 Feb 2018 22:56:36 +0000 (17:56 -0500)]
Infineon TPM: Fix potential buffer overruns

Ensure that the Infineon I2C and SPI TPM driver performs adequate
validation of the length extracted from the TPM response header.
This patch prevents integer underflow when the length was too small,
which could lead to memory corruption.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
6 years agoSTMicro TPM: Fix potential buffer overruns
Jeremy Boone [Mon, 12 Feb 2018 22:56:35 +0000 (17:56 -0500)]
STMicro TPM: Fix potential buffer overruns

This patch prevents integer underflow when the length was too small,
which could lead to memory corruption.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
6 years agoARM: dts: rmobile: Add PHY reset GPIO
Marek Vasut [Fri, 15 Sep 2017 19:11:40 +0000 (21:11 +0200)]
ARM: dts: rmobile: Add PHY reset GPIO

This patch got dropped during the update of DTs to 4.14, re-add it
back. This adds reset GPIOs to the ethernet PHYs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: dts: rmobile: Make PFC and RST available early on Gen2 only
Marek Vasut [Mon, 5 Mar 2018 09:57:40 +0000 (10:57 +0100)]
ARM: dts: rmobile: Make PFC and RST available early on Gen2 only

These do not need to be available early on Gen3 , so move them to
the respective DT files.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Add R8A77965 Salvator-XS board support
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
ARM: rmobile: Add R8A77965 Salvator-XS board support

Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: dts: rmobile: Add SDHI nodes to R8A77965 M3N DT
Marek Vasut [Thu, 1 Mar 2018 20:52:19 +0000 (21:52 +0100)]
ARM: dts: rmobile: Add SDHI nodes to R8A77965 M3N DT

Add SDHI nodes to r8a77965.dtsi to get eMMC and SD slots operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: dts: rmobile: Add xHCI node to R8A77965 M3N DT
Marek Vasut [Thu, 1 Mar 2018 20:51:11 +0000 (21:51 +0100)]
ARM: dts: rmobile: Add xHCI node to R8A77965 M3N DT

Add xHCI node to r8a77965.dtsi to get xHCI USB operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: dts: rmobile: Add EHCI nodes to R8A77965 M3N DT
Marek Vasut [Thu, 1 Mar 2018 20:51:05 +0000 (21:51 +0100)]
ARM: dts: rmobile: Add EHCI nodes to R8A77965 M3N DT

Add generic EHCI nodes to r8a77965.dtsi to get EHCI USB operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: dts: rmobile: Add RAVB node to R8A77965 M3N DT
Marek Vasut [Thu, 1 Mar 2018 20:50:56 +0000 (21:50 +0100)]
ARM: dts: rmobile: Add RAVB node to R8A77965 M3N DT

Add RAVB node to r8a77965.dtsi to get ethernet operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: dts: rmobile: Import R8A77965 M3N DT files from Linux
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
ARM: dts: rmobile: Import R8A77965 M3N DT files from Linux

Import the R8A77965 M3N DT from Linux 4.16-rc1 .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agousb: xhci-rcar: Add R8A77965 M3N entries
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
usb: xhci-rcar: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agopinctrl: rmobile: Add R8A77965 M3N entries
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
pinctrl: rmobile: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agonet: ravb: Add R8A77965 M3N entries
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
net: ravb: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
6 years agommc: uniphier-sd: Add R8A77965 M3N entries
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
mmc: uniphier-sd: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agogpio: rcar: Add R8A77965 M3N entries
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
gpio: rcar: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoclk: renesas: Add R8A77965 M3N entries
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
clk: renesas: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Add R8A77965 M3N IDs
Marek Vasut [Mon, 26 Feb 2018 09:35:15 +0000 (10:35 +0100)]
ARM: rmobile: Add R8A77965 M3N IDs

Add CPU and PRR IDs for R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoMerge branch 'master' of git://git.denx.de/u-boot-socfpga
Tom Rini [Thu, 1 Mar 2018 20:50:52 +0000 (15:50 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga

6 years agoMerge branch 'master' of git://git.denx.de/u-boot-sh
Tom Rini [Thu, 1 Mar 2018 20:50:43 +0000 (15:50 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sh

6 years agoMerge tag 'xilinx-kconfig-for-v2018.03' of git://www.denx.de/git/u-boot-microblaze
Tom Rini [Thu, 1 Mar 2018 17:41:21 +0000 (12:41 -0500)]
Merge tag 'xilinx-kconfig-for-v2018.03' of git://www.denx.de/git/u-boot-microblaze

Xilinx Kconfig changes for v2018.03

- Moving some macros to Kconfig

# gpg: Signature made Thu 01 Mar 2018 10:45:58 AM EST using DSA key ID 294A0C21
# gpg: Good signature from "Michal Simek <monstr@monstr.eu>"
# gpg:                 aka "Michal Simek (Xilinx) <michals@xilinx.com>"
# gpg:                 aka "Michal Simek (Xilinx) <michal.simek@xilinx.com>"

6 years agommc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
Vipul Kumar [Wed, 28 Feb 2018 10:23:29 +0000 (15:53 +0530)]
mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ

This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agommc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
Vipul Kumar [Wed, 28 Feb 2018 10:23:28 +0000 (15:53 +0530)]
mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ

This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agomicroblaze: Added Kconfig support for CONFIG_XILINX_GPIO
Vipul Kumar [Wed, 28 Feb 2018 06:02:22 +0000 (11:32 +0530)]
microblaze: Added Kconfig support for CONFIG_XILINX_GPIO

This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoi2c: Added kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1
Vipul Kumar [Fri, 16 Feb 2018 13:37:22 +0000 (19:07 +0530)]
i2c: Added kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1

This patch added Kconfig support for CONFIG_ZYNQ_I2C0 and
CONFIG_ZYNQ_I2C1 and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoi2c: Added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET
Vipul Kumar [Fri, 16 Feb 2018 13:37:21 +0000 (19:07 +0530)]
i2c: Added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET

This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoi2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
Vipul Kumar [Fri, 16 Feb 2018 13:37:20 +0000 (19:07 +0530)]
i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
and set it to default value 100000.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoi2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
Vipul Kumar [Fri, 16 Feb 2018 13:37:19 +0000 (19:07 +0530)]
i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoi2c: Enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfig
Vipul Kumar [Fri, 16 Feb 2018 13:37:18 +0000 (19:07 +0530)]
i2c: Enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfig

This patch enabled CONFIG_SYS_I2C_ZYNQ in the respective
defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoi2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ
Vipul Kumar [Fri, 16 Feb 2018 13:37:17 +0000 (19:07 +0530)]
i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoarm: zynq: fpga: Added Kconfig support for CONFIG_FPGA_ZYNQPL
Vipul Kumar [Fri, 16 Feb 2018 12:32:51 +0000 (18:02 +0530)]
arm: zynq: fpga: Added Kconfig support for CONFIG_FPGA_ZYNQPL

This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the
values over to the defconfigs.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
6 years agofpga: Added Kconfig support for FPGA_SPARTAN3
Vipul Kumar [Fri, 16 Feb 2018 12:32:49 +0000 (18:02 +0530)]
fpga: Added Kconfig support for FPGA_SPARTAN3

This patch added Kconfig support for FPGA_SPARTAN3 and migrates the
values over to the defconfigs.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
6 years agoMerge git://git.denx.de/u-boot-net
Tom Rini [Wed, 28 Feb 2018 01:10:28 +0000 (20:10 -0500)]
Merge git://git.denx.de/u-boot-net

6 years agoKconfig: cmd: Make networking command dependent on NET
Michal Simek [Mon, 26 Feb 2018 15:01:02 +0000 (16:01 +0100)]
Kconfig: cmd: Make networking command dependent on NET

Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoARM: rmobile: Build u-boot-spl.srec on Gen2
Marek Vasut [Mon, 26 Feb 2018 19:19:08 +0000 (20:19 +0100)]
ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
6 years agoMakefile: add u-boot-spl.srec target
Marek Vasut [Mon, 26 Feb 2018 19:14:02 +0000 (20:14 +0100)]
Makefile: add u-boot-spl.srec target

The u-boot-spl.srec is needed for some platforms, add target to generate this file.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
6 years agoARM: rmobile: Build u-boot-elf.srec on Gen3
Masaru Nagai [Fri, 28 Aug 2015 03:12:45 +0000 (12:12 +0900)]
ARM: rmobile: Build u-boot-elf.srec on Gen3

The u-boot-elf.srec is needed for the minimon update on Gen3 SoCs,
conveniently generate this file.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoMakefile: add u-boot-elf.srec target
Masaru Nagai [Fri, 28 Aug 2015 03:12:45 +0000 (12:12 +0900)]
Makefile: add u-boot-elf.srec target

The u-boot-elf.srec is needed for some platforms, add target to generate this file.

Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoarm: socfpga: cyclone5: Enable Macronix flash support
Chin Liang See [Tue, 27 Feb 2018 09:25:02 +0000 (17:25 +0800)]
arm: socfpga: cyclone5: Enable Macronix flash support

Enable Macronix flash support for Cyclone5 SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
6 years agonet: phy: smsc: Add SMSC LAN8741 support
Arno Steffens [Thu, 25 Jan 2018 12:08:35 +0000 (13:08 +0100)]
net: phy: smsc: Add SMSC LAN8741 support

Signed-off-by: Arno Steffens <star@gmx.li>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
6 years agonet: e1000: Fix e1000_igb semaphore handling
Bernhard Messerklinger [Thu, 15 Feb 2018 07:55:49 +0000 (08:55 +0100)]
net: e1000: Fix e1000_igb semaphore handling

Fix commit f1bcad22dd19 ("net: e1000: add support for writing to
EEPROM").

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
6 years agoNET: designware: fix clock enable
Eugeniy Paltsev [Tue, 6 Feb 2018 14:12:09 +0000 (17:12 +0300)]
NET: designware: fix clock enable

After commit ba1f966725223 ("net: designware: add clock support")
we got NET broken on axs101 and axs103 platforms.

Some clock don't support gating so their clock drivers don't
implement .enable/.disable callbacks. In such case clk_enable
returns -ENOSYS.
Also some clock drivers implement .enable/.disable callbacks not for all
clock IDs and return -ENOSYS (or -ENOTSUPP) for others.

If we have such clock in 'clocks' list of designware ethernet controller
node we fail to probe designware ethernet.

Fix it.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
6 years agophy: Fix style violations
Mario Six [Mon, 15 Jan 2018 10:08:27 +0000 (11:08 +0100)]
phy: Fix style violations

Fix some style violations in the generic PHY management code.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
6 years agocmd: mdio: Fix style violations
Mario Six [Mon, 15 Jan 2018 10:08:26 +0000 (11:08 +0100)]
cmd: mdio: Fix style violations

Fix some style violations in the MDIO command.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
6 years agonet: phy: marvell 88e151x: Fix handling of bare RGMII interface type
Mario Six [Mon, 15 Jan 2018 10:08:25 +0000 (11:08 +0100)]
net: phy: marvell 88e151x: Fix handling of bare RGMII interface type

Commit 68e6ecadc551 ("net: phy: marvell 88e151x: Fix handling of RGMII
interface types") fixed the initialization of 88e151x phys, but made it
so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX
delay bits cleared. The default (like in m88e1111s_config) is to have
both bits set.

Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII
case so that both bits are set.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
6 years agonet: phy: marvell: Fix style violations
Mario Six [Mon, 15 Jan 2018 10:08:24 +0000 (11:08 +0100)]
net: phy: marvell: Fix style violations

Fix some style violations (mostly wrong indentions) in the Marvell PHY
driver.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
6 years agonet: tsec: Make live-tree compatible
Mario Six [Mon, 15 Jan 2018 10:08:23 +0000 (11:08 +0100)]
net: tsec: Make live-tree compatible

Make the tsec ethernet driver compatible with a live device tree.

Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
6 years agonet: tsec: Fix memory leak in error path
Mario Six [Mon, 15 Jan 2018 10:08:22 +0000 (11:08 +0100)]
net: tsec: Fix memory leak in error path

tsec_initialize allocates a private driver structure using malloc.
Should the memory allocation of this private structure fail, the
function execution is aborted with a return 0, but the previously
allocated device structure is never freed, hence leaked.

Free the device structure in the error case.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
6 years agonet: tsec: Fix style violations
Mario Six [Mon, 15 Jan 2018 10:08:21 +0000 (11:08 +0100)]
net: tsec: Fix style violations

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
6 years agoARM: dts: rmobile: Import proper DTS for H2 Stout
Marek Vasut [Mon, 26 Feb 2018 18:55:37 +0000 (19:55 +0100)]
ARM: dts: rmobile: Import proper DTS for H2 Stout

Replace the placeholder DTS for R8A7790 H2 Stout with a proper
DTS from Linux next .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: socfpga: Add new CycloneV SoC Devboards DBM-SoC1 board
Marek Vasut [Sat, 24 Feb 2018 22:34:00 +0000 (23:34 +0100)]
ARM: socfpga: Add new CycloneV SoC Devboards DBM-SoC1 board

Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.

Signed-off-by: Marek Vasut <marex@denx.de>
6 years agoMerge git://git.denx.de/u-boot-mmc
Tom Rini [Mon, 26 Feb 2018 03:28:59 +0000 (22:28 -0500)]
Merge git://git.denx.de/u-boot-mmc

6 years agommc: omap_hsmmc: use a default 52MHz max clock rate if none is specified
Jean-Jacques Hiblot [Fri, 23 Feb 2018 09:40:19 +0000 (10:40 +0100)]
mmc: omap_hsmmc: use a default 52MHz max clock rate if none is specified

mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
6 years agommc: omap_hsmmc: make it possible to compile out ADMA support
Jean-Jacques Hiblot [Fri, 23 Feb 2018 09:40:18 +0000 (10:40 +0100)]
mmc: omap_hsmmc: make it possible to compile out ADMA support

Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
6 years agommc: omap_hsmmc: compile out write support if not needed
Jean-Jacques Hiblot [Fri, 23 Feb 2018 09:40:17 +0000 (10:40 +0100)]
mmc: omap_hsmmc: compile out write support if not needed

This reduces the size of the binary by about 196 bytes.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
6 years agommc: omap_hsmmc: do not embed struct mmc in struct omap_hsmmc_plat
Jean-Jacques Hiblot [Fri, 23 Feb 2018 09:40:16 +0000 (10:40 +0100)]
mmc: omap_hsmmc: do not embed struct mmc in struct omap_hsmmc_plat

The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.

This saves around 740 bytes for the am335x_evm SPL.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
6 years agoMerge git://git.denx.de/u-boot-rockchip
Tom Rini [Sun, 25 Feb 2018 20:39:10 +0000 (15:39 -0500)]
Merge git://git.denx.de/u-boot-rockchip

6 years agoMerge git://git.denx.de/u-boot-imx
Tom Rini [Sun, 25 Feb 2018 20:38:42 +0000 (15:38 -0500)]
Merge git://git.denx.de/u-boot-imx

6 years agobootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDR
Tom Rini [Sat, 24 Feb 2018 21:50:41 +0000 (16:50 -0500)]
bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDR

Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig.  We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use.  We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig.  In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files.  The previous default
only applied in some cases, even on a specific SoC family.

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoimx: spl: Partially revert "spl: eMMC/SD: Provide one __weak spl_boot_mode() function"
Fabio Estevam [Thu, 15 Feb 2018 14:41:40 +0000 (12:41 -0200)]
imx: spl: Partially revert "spl: eMMC/SD: Provide one __weak spl_boot_mode() function"

Commit d695d6627803 ("spl: eMMC/SD: Provide one __weak spl_boot_mode()
function") breaks the boot on several i.MX6 boards,
such as cuboxi and wandboard:

U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300)
Trying to boot from MMC1
Failed to mount ext2 filesystem...
spl_load_image_ext: ext4fs mount err - 0

Partially revert it so that we can boot U-Boot again on these
i.MX6 platforms.

Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
6 years agorockchip: clk: rk3399: handle set_rate/get_rate for PLL_PPLL
Philipp Tomsich [Fri, 23 Feb 2018 16:36:41 +0000 (17:36 +0100)]
rockchip: clk: rk3399: handle set_rate/get_rate for PLL_PPLL

The device-tree node for the PMU clk controller assigns to its parent
(i.e. PLL_PPLL) even though this clock currently is set up statically
by an init-function.

In order to avoid unexpected failures, a simple implementation of
set_rate (which accepts requests, but notifies the caller of the
preset frequency in its return value) and get_rate (which always
returns the preset frequency) are added.

Note that this is required for the RK808 PMIC to probe successfully on
the RK3399-Q7, following the support for the assigned-clocks property.

References: commit f4fcba5c5baa ("clk: implement clk_set_defaults()")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
6 years agorockchip: rk3288: Fix wrong TPL_TEXT_BASE
Jagan Teki [Fri, 23 Feb 2018 07:43:11 +0000 (13:13 +0530)]
rockchip: rk3288: Fix wrong TPL_TEXT_BASE

TPL offset 0xff704004 is unaligned address which is adding nearest
8-bytes for next instruction, So  0xff704004 is adding 0x20 for
proper alignment which is causing the next instruction data
0xefffffff is moved.

Hexdump with overlaped bytes:
-----------------------------
0000000 0000 0000 0000 0000 0000 0000 0000 0000
0000010 0000 0000 0000 0000 0000 0000 ffff eaff

So, Fix the TEXT_BASE for proper aligned address 0xff704000

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
6 years agorockchip: rk3288: Add TPL_LDSCRIPT
Jagan Teki [Fri, 23 Feb 2018 07:43:10 +0000 (13:13 +0530)]
rockchip: rk3288: Add TPL_LDSCRIPT

Due to size limitations in SPL by adding falcon mode,
rk3288 support TPL. In order to not overlap SPL_TEXT_BASE
add TPL_TEXT_BASE with u-boot-tpl.lds that intern call
u-boot-spl.lds with proper TEXT_BASE values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
6 years agorockchip: clk: rk3368: handle clk_enable requests for GMAC
Philipp Tomsich [Fri, 16 Feb 2018 15:07:25 +0000 (16:07 +0100)]
rockchip: clk: rk3368: handle clk_enable requests for GMAC

Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3368 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the RK3368 clk driver to:
(a) provide a enable op
(b) signals success to the caller when the clocks for the GMAC are
    enabled (no actual action is necessary as the gates are open
    after reset)

References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
6 years agorockchip: clk: rk3399: handle clk_enable requests for GMAC
Philipp Tomsich [Fri, 16 Feb 2018 15:07:24 +0000 (16:07 +0100)]
rockchip: clk: rk3399: handle clk_enable requests for GMAC

Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3399 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the enable-op of the rk3399 clk driver to signal
success to the caller when the clocks for the GMAC are enabled.

References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
6 years agoARM: dts: i.MX6QDL: icore-rqs: Fix eMMC detection during SPL
Jagan Teki [Wed, 21 Feb 2018 13:05:56 +0000 (18:35 +0530)]
ARM: dts: i.MX6QDL: icore-rqs: Fix eMMC detection during SPL

usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
6 years agoRemove CONFIG_SYS_BOOTCOUNT_SINGLEWORD
Alex Kiernan [Fri, 16 Feb 2018 15:50:48 +0000 (15:50 +0000)]
Remove CONFIG_SYS_BOOTCOUNT_SINGLEWORD

Tidy up CONFIG_SYS_BOOTCOUNT_SINGLEWORD from the whitelist as there's
no remaining uses of it left.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agoMigrate CONFIG_BOOTCOUNT_ALEN to Kconfig
Alex Kiernan [Fri, 16 Feb 2018 15:50:47 +0000 (15:50 +0000)]
Migrate CONFIG_BOOTCOUNT_ALEN to Kconfig

Convert CONFIG_BOOTCOUNT_ALEN to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agoMigrate generic bootcount to Kconfig
Alex Kiernan [Fri, 16 Feb 2018 15:50:46 +0000 (15:50 +0000)]
Migrate generic bootcount to Kconfig

Make generate boot counter selected in the same way as other boot count
drivers

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agoIntegrate AT91 bootcount driver
Alex Kiernan [Fri, 16 Feb 2018 15:50:45 +0000 (15:50 +0000)]
Integrate AT91 bootcount driver

Integrate Boot counter for Atmel AT91SAM9XE into Kconfig

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agoConvert CONFIG_BOOTCOUNT_EXT to Kconfig
Alex Kiernan [Fri, 16 Feb 2018 15:50:44 +0000 (15:50 +0000)]
Convert CONFIG_BOOTCOUNT_EXT to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_EXT

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agoConvert CONFIG_BOOTCOUNT_I2C to Kconfig
Alex Kiernan [Fri, 16 Feb 2018 15:50:43 +0000 (15:50 +0000)]
Convert CONFIG_BOOTCOUNT_I2C to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_I2C

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
6 years agoConvert CONFIG_BOOTCOUNT_RAM to Kconfig
Alex Kiernan [Fri, 16 Feb 2018 15:50:42 +0000 (15:50 +0000)]
Convert CONFIG_BOOTCOUNT_RAM to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_RAM

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
6 years agoConvert CONFIG_BOOTCOUNT_ENV to Kconfig
Alex Kiernan [Fri, 16 Feb 2018 15:50:41 +0000 (15:50 +0000)]
Convert CONFIG_BOOTCOUNT_ENV to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_ENV

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
6 years agoConvert CONFIG_BOOTCOUNT_AM33XX to Kconfig
Alex Kiernan [Fri, 16 Feb 2018 15:50:40 +0000 (15:50 +0000)]
Convert CONFIG_BOOTCOUNT_AM33XX to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_AM33XX

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agoPrepare for multiple bootcount drivers
Alex Kiernan [Fri, 16 Feb 2018 15:50:39 +0000 (15:50 +0000)]
Prepare for multiple bootcount drivers

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agoMerge CONFIG_BOOTCOUNT and CONFIG_BOOTCOUNT_LIMIT
Alex Kiernan [Fri, 16 Feb 2018 15:50:38 +0000 (15:50 +0000)]
Merge CONFIG_BOOTCOUNT and CONFIG_BOOTCOUNT_LIMIT

CONFIG_BOOTCOUNT was only used in mx53ppd, merge it with
CONFIG_BOOTCOUNT_LIMIT

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Ian Ray <ian.ray@ge.com>
6 years agoMerge git://git.denx.de/u-boot-video
Tom Rini [Sat, 24 Feb 2018 13:02:17 +0000 (08:02 -0500)]
Merge git://git.denx.de/u-boot-video