sunxi: DRAM initialisation for sun9i

This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.

With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.

[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

tools: add mksunxiboot to tools-all target

mksunxiboot is useful outside of u-boot, it is e.g. used by sunxi-tools.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: A64: enable USB support

Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Update DRAM clock for Olimex A20 boards

Originally dram clock was set to 480MHz, but this behaves
unstable. To improve stability the clock is reduced to 384MHz

Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: dts: Pine64: add Ethernet alias

The sun8i-emac driver works fine with the A64 Ethernet IP, but we are
missing an alias entry to trigger the driver instantiation by U-Boot.
Add the line to point U-Boot to the Ethernet DT node.
This enables TFTP boot on the Pine64.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: remove unneeded CONFIG_USB_MAX_CONTROLLER_COUNT defines

ARCH_SUNXI selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT
is not used.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXI

CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt

Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

configs/chromebox_panther_defconfig: Re-enable CONFIG_DM_PCI

This was turned off by accident, re-enble.

Signed-off-by: Tom Rini <trini@konsulko.com>

MAINTAINERS: Update Jagan's email

Signed-off-by: Jagan Teki <jagan@openedev.com>

travis-ci: build Tegra boards

ARMv7 Tegra boards aren't currently covered by any other travis-ci jobs.
Add a new job to build them.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: compile with buildman when running test/py

Use buildman to compile any U-Boot binary tested by test/py. This
re-uses all the work done elsewhere to make buildman work within
Travis-CI, in particular related to toolchain downloading and buildman
config file creation.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: don't invoke exit on success

Invoking exit prevents any subsequent build commands from running, and
future patches will add extra commands.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: use buildman -P everywhere

This places build results into a board-specific directory rather than a
buildman-thread-specific directory. This is required so that we can
access the directory from test.py, and there's no risk of a particular
build's results being over-written by another build performed by the
same thread.

In theory, this can lead to slower builds when building many different
boards in a single buildman thread, since it removes the possibility of
incremental builds between boards. In practice however I didn't notice
longer build times when when enabling this option; if anything build
times decreased although I suspect that's simply due to general
variations in build performance across different machines within the
Travis CI infra-structure.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: centralize ~/.buildman editing

Any time an x86 toolchain is used, we need to edit ~/.buildman to
reference it. Move the editing logic into a central place so that it
doesn't have to be duplicated everywhere that uses the x86 toolchain;
future patches will add additional cases where it's used.

It would be nice if we could unconditionally write all of ~/.buildman at
once. Unfortunately, buildman fails if any toolchain mentioned in a
toolchain-prefix entry doesn't exist, even if it doesn't need to use it
for the current build.

The sandbox/x86 build definition currently does nothing more than edit
~/.buildman; no builds are run. Fix this by not defining a custom script
for this build, and hence preventing that stanza from replacing the
default script.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: use correct exit code on errors

The phrase "if [ $? -ne 0 ]; then exit $?; fi" doesn't work correctly;
by the time the "exit" statement runs, $? has already been over-written
by the result of the [ command. Fix this by explicitly storing $? and
then using that stored value in both the test and the error-case exit
statement.

This change also converts from textual comparison to integer comparison,
since the exit code is an integer and there's no need to convert it to
a string for comparison.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: Use = not : when writing ~/.buildman

Travis CI seems to be confused when there's a colon in an echo command,
and this is currently worked around using a variable that contains the
text we want to echo. Use = syntax instead so that we can remove the
work-around; it's rather confusing until you find out what it's for.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: remove duplicate build

There were two sub-jobs to build arm1136. Remove the duplicate.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

travis-ci: set env vars to name jobs

Travis CI names sub-jobs after the first environment variable that is set
for a script. This doesn't produce meaningful results for any of the non-
buildman jobs. Add a dummy variable to give the jobs meaningful names.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git://git.denx.de/u-boot-atmel

dm: at91: Add driver model support for the spi driver

Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>

board: sama5d2_xplained: Enable an early debug UART

Enable an early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>

board: sama5d2_xplained: Set 'ethaddr' got from AT24MAC

If 'ethaddr' is not set, we will get the ethernet address from AT24MAC,
and set it to 'ethaddr' variable.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Reviewed-by: Andreas Bießmann <biessmann@corscience.de>

board: sama5d2_xplained: Clean up code

Since the introduction of pinctrl and clk driver, and the dts file,
remove unneeded the pin configurations and the clock enabling code.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>

board: sama5d2_xplained: Move config options to defconfigs

Move the config options from the include/configs/sama5d2_xplained.h
to configs/sama5d2_xplained_*_defconfig.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>

serial: atmel_usart: Support enable an early debug UART

Add support to enable an early debug UART for debugging.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

serial: Kconfig: Add ATMEL_USART option

Add ATMEL_USART option to support to enable the Atmel usart driver
from Kconfig.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

mmc: atmel_sdhci: Remove unnecessary clock calling

Due to the peripheral and generated clock driver improvement,
remove the unnecessary clock calling.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

usb: ehci-atmel: Remove unnecessary clock calling

Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

i2c: at91_i2c: Change error return -ENODEV to -EINVAL

Change the error return value -ENODEV from to -EINVAL for more
reasonable.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

i2c: at91_i2c: Remove unnecessary clock calling

Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

gpio: atmel_pio4: Remove unnecessary clock calling

Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

clk: at91: Improve the clock implementation

For the peripheral clock, provide the clock ops for the clock
provider, such as spi0_clk. The .of_xlate is to get the clk->id,
the .enable is to enable the spi0 peripheral clock, the .get_rate
is to get the clock frequency.

The driver for periph32ck node is responsible for recursively
binding its children as clk devices, not provide the clock ops.

So do the generated clock and system clock.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

clk: clk-uclass: Assign clk->dev before call .of_xlate

In order to make clk->dev available in ops->of_xlate() to get the
clock ID from the 'reg' property of the clock node, assign the
clk->dev before calling ops->of_xlate().

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

ARM: at91/dt: sama5d2: Fix the warning from dtc

Fix the warning from dtc like,
---8<----
Warning (unit_address_vs_reg): Node /ahb/apb/pmc@f0014000/periph64ck/sdmmc0_hclk has a reg or ranges property, but no unit name
--->8----

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

clk: at91: Fix at91-pmc and at91-sckc's class ID

The at91-pmc and at91-sckc aren't the clock providers, change their
class ID from UCLASS_CLK to UCLASS_SIMPLE_BUS, they also don't
need to bind the child nodes explicitly, the .post_bind callback
of simple_bus uclass will do it for them.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

AT91: Correct misspelling of "redundent" in partition names

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

arm, at91: add icache support

add at least icache support for at91 based boards.
This speeds up NOR flash access on an at91sam9g15
based board from 15.2 seconds reading 8 MiB from
a SPI NOR flash to 5.7 seconds.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

ARM: at91: clock: correct PRES offset for at91sam9x5

on at91sam9x5 PRES offset is 4 in the PMC master
clock register.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Andreas Bießmann <andreas@biessmann.org>

arm: at91: mpddrc: add missing MPDDRC_MD defines

add missing MPDDRC_MD defines

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
common/Kconfig
configs/dms-ba16_defconfig

Merge branch 'master' of http://git.denx.de/u-boot-mmc

pci: Move CONFIG_PCI_PNP to Kconfig

Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes]
Signed-off-by: Tom Rini <trini@konsulko.com>

mmc: sdhci: assign to clk_mul when host version is upper than SD3.0

To prevent the wrong value check the SD version.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

mmc: add the device name in debugging message for supplying vmmc

If vmmc didn't supply, we didn't know which card didn't supply vmmc.
And changed from "put" to "debug".

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

dm: mmc: socfpga: fix MMC_OPS support

Now that CONFIG_BLK and CONFIG_MMC_OPS are enabled by default with
CONFIG_DM_MMC, the DWMMC driver on the socfpga platform fails at
runtime.

This adds the missing fields in the driver declaration.

Signed-off-by: Sylvain Lesne <lesne@alse-fr.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

mmc: refactor two core functions

Drop unneeded variables and assignments.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mmc: sdhci: fix the "misaligned operation at range" for cache

This pathc is fixed the below thing.
If misaligned the cache range, Just flush to CACHLINE_SIZE.
"CACHE: Misaligned operation at range [7ae55b00, 7ae55b08]"

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

mmc: introduce mmc_power_init

In device tree, there is vmmc-supply property for SD/MMC.
Introduce mmc_power_init function to handle vmmc-supply.

mmc_power_init will first invoke board_mmc_power_init to
avoid break boards which already implement board_mmc_power_init.

If DM_MMC and DM_REGULATOR is defined, the regulator
will be enabled to power up the device.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

drivers/pci/Kconfig: Add PCI

Add 'PCI' as a menu option and migrate all existing users.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

imx6: icorem6: Add default mtd nand partition table

icorem6qdl> mtdparts

device nand0 <nand>, # parts = 6
0: spl                 0x00200000      0x00000000      0
1: uboot               0x00200000      0x00200000      0
2: env                 0x00100000      0x00400000      0
3: kernel              0x00400000      0x00500000      0
4: dtb                 0x00100000      0x00900000      0
5: rootfs              0x1f600000      0x00a00000      0

Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx6: icorem6: Enable MTD device support

Enable MTD device, partition and command support.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx6: icorem6: Add NAND support

Add NAND support for Engicam i.CoreM6 qdl board.

Boot Log:
--------

U-Boot SPL 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43)
Trying to boot from NAND
NAND : 512 MiB

U-Boot 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43 +0530)

CPU:   Freescale i.MX6SOLO rev1.3 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 55C
Reset cause: WDOG
Model: Engicam i.CoreM6 DualLite/Solo Starter Kit
DRAM:  256 MiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
icorem6qdl>

Cc: Scott Wood <oss@buserror.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

mtd: nand: Kconfig: Add NAND_MXS entry

Added kconfig for NAND_MXS driver.

Cc: Scott Wood <oss@buserror.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual

i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU           NXP i.MX6 DQ, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: dts: imx6q: Add pinctrl defines

Add imx6q pinctrl defines support from Linux.

Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: dts: Add devicetree for i.MX6Q

Add i.MX6Q dtsi support from Linux.

Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

engicam: icorem6: Add DM_GPIO, DM_MMC support

Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx6q: icorem6: Enable pinctrl driver

Enable imx6 pinctrl driver support for i.CoreM6.

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo

i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU           NXP i.MX6 DL, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

dt-bindings: clock: imx6qdl: Add clock defines

Add imx6qdl clock header defines support from Linux.

"clk: imx: Add clock support for imx6qp"
(sha1: ee36027427c769b0b9e5e205fe43aced93d6aa66)

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: dts: imx6dl: Add pinctrl defines

Add imx6dl pinctrl defines support from Linux.

Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: dts: Add devicetree for i.MX6DQL

Add i.MX6DQL dtsi support from Linux.

Here is the last commit:
"ARM: dts: imx6qdl: Fix SPDIF regression"
(sha1: f065e9e4addd75c21bb976bb2558648bf4f61de6)

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: dts: Add devicetree for i.MX6DL

Add i.MX6DL dtsi support from Linux.

Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx: s/docs\/README.imximage/doc\/README.imximage/g

Fixed typo for doc/README.imximage on respective imximage.cfg files.

Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx6: icorem6: Add ENET support

Add enet support for engicam icorem6 qdl starter kit.
- Add pinmux settings
- Add board_eth_init

TFTP log:
--------
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb
Using FEC device
TFTP from server 192.168.2.96; our IP address is 192.168.2.75
Filename 'imx6dl-icore.dtb'.
Load address: 0x0
Loading: ######
         1.3 MiB/s
done
Bytes transferred = 28976 (7130 hex)
CACHE: Misaligned operation at range [00000000, 00007130]
icorem6qdl>

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: Kconfig: Add FEC_MXC entry

Added kconfig for FEC_MXC driver.

Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support

Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6SOLO rev1.3 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM:  256 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
   Booting using the fdt blob at 0x18000000
   Using Device Tree in place at 18000000, end 1800a787

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0

Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6Q rev1.2 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs

- Add DEFAULT_FDT_FILE kconfig entry
- Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs

Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

thermal: Kconfig: Add IMX_THERMAL entry

Added kconfig for IMX_THERMAL driver.

Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

serial: Kconfig: Add MXC_UART entry

Added kconfig for MXC_UART driver.

Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx: mx6ull_14x14_evk: add plugin defconfig

Add defconfig file to use plugin code.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

i2c: designware: Avoid overwriting the cmd_data register

Make sure the driver writes the cmd_data register only once per
read transfer instead of doing so potentially repeatedly.

In case the read transfer didn't finish quickly enough, the loop
in the driver code would spin fast enough to write the same value
into the cmd_data register again before re-checking whether the
transfer completed, which would cause another spurious read transfer
on the bus.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>

travis-ci: Add test.py for various qemu platforms

- Add a PPA for a more recent qemu (required for PowerPC to work)
- Add tests to run test.py for various QEMU platforms.  This relies on
  swarren's uboot-test-hooks repository to provide the abstractions.

Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

travis-ci: Drop 'TEST_CMD'

We don't need to use TEST_CMD in order to run tests.  We need a BUILDMAN
and TOOLCHAIN variable to avoid having to duplicate logic or write some
wrapper function.  But this makes the tests harder as we add more
complex examples.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: Add more architectures

We can now build for microblaze, sh4 and xtensa.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: Update toolchain and buildman usage

- Drop the 'cache' line, travis-ci says to not cache apt packages (and
  does not).
- Get the Ubuntu provided toolchain for ARM and PowerPC.
- Add more toolchain options that buildman can fetch.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: Do not make buildman warnings fatal

We currently will always see a number of warnings due to device tree
issues.  These (and other warnings) should not make the build be marked
as failure so catch exit status 129 specifically and return 0 in that
case.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: Use a git URI for dtc.git

Currently we fail to fetch the dtc.git tree due to an SSL issue within
the travis-ci environment.  The easiest fix here is to switch to a git
URI.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

travis-ci: Switch to Ubuntu 14.04 'Trusty Tahr'

In order to make other various improvements, update to the latest
environment travis-ci supports.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

api: storage: Avoid enumeration for non-configured subsystem

If a subsystem wasn't configured, avoid enumeration.

Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>

tools: moveconfig: support wildcards in --defconfigs file

Supporting shell-style wildcards for the --defconfigs option will be
useful to run the moveconfig tool against a specific platform.  For
example, "uniphier*" in the file passed by --defconfigs option will
be expanded to defconfig files that start with "uniphier".  This is
easier than listing out all defconfig files you are interested in.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>

Fix codying style broken by recent libfdt sync

Commit b02e4044ff8e ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>

libfdt: fix fdt_stringlist_search()

If fdt_getprop() fails, negative error code should be returned.

[ DTC commit: daa75e8fa5942caa8e97931aed3a1ee0b7edd74b ]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

libfdt: fix fdt_stringlist_count()

If fdt_getprop() fails, negative error code should be returned.

[ DTC commit: e28eff5b787adb3f461d1653598818b2f1f25a73 ]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

power: twl6030: fix code refactoring

Commit a85362fb3e1fc7833723accddbbae431091d06b8 refactored the code
but the register read ended up in the wrong if branch.
Currently, the else branch checks a variable which is always 0.

Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

ext4: Only write journal entries for modified blocks in unlink_filename

Instead of creating a journal entry for each directory block, even
if the block is unmodified, only log the modified block.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

ext4: Fix handling of direntlen in unlink_filename

The direntlen checks were quite bogus, i.e. the loop termination used
"len + offset == blocksize" (exact match only), and checked for a
direntlen less than 0. The latter can never happen as the len is
unsigned, this has been reported by Coverity, CID 153384.

Use the same code as in search_dir for directory traversal. This code
has the correct checks for direntlen >= sizeof(struct dirent), and
offset < blocksize.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reported-by: Coverity (CID: 153383, 153384)
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

ext4: cleanup unlink_filename function

Use the same variable names as in search_dir, to make purpose of variables
more obvious.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-fdt

imx: mx6ullevk: correct boot device macro

Correct boot device macro according to kconfig entry
in common/Kconfig

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

imx: mx6ullevk: support plugin

Add plugin code for mx6ullevk.
Define CONFIG_USE_IMXIMG_PLUGIN in defconfig file to use plugin code.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

imx-common: compile plugin code

If CONFIG_USE_IMXIMG_PLUGIN is selected, plugin.bin will be
generated under board/$(BOARDDIR)/.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

imx-common: introduce USE_IMXIMG_PLUGIN Kconfig

Introduce USE_IMXIMG_PLUGIN Kconfig

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

imx: mx7: Add plugin support

Add mx7_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

imx: mx6: Add plugin support

Add mx6_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>

tools: imximage: add plugin support

Add plugin support for imximage.

Define CONFIG_USE_IMXIMG_PLUGIN in defconfig to enable using plugin.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_STDIO_DEREGISTER to Kconfig

This converts the following to Kconfig:
   CONFIG_SYS_STDIO_DEREGISTER

This option should never be enabled in SPL, so use
CONFIG_IS_ENABLED(SYS_STDIO_DEREGISTER) when checking the option.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USB_KEYBOARD to Kconfig

This converts the following to Kconfig:
   CONFIG_USB_KEYBOARD

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup MPC86* configs]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_INFO_QUIET to Kconfig

This converts the following to Kconfig:
   CONFIG_SYS_CONSOLE_INFO_QUIET

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to Kconfig

This converts the following to Kconfig:
   CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>