Albert ARIBAUD [Fri, 20 Jul 2012 06:51:26 +0000 (08:51 +0200)]
Revert "arm: armv7: add compile option -mno-unaligned-access if available"
This reverts commit 5347560f5427bcdd48a563b62180481606ac8044,
which was applied only to get release 2012.07 functional on as
many ARM targets as possible despite mis-aligned accesses.
omap2plus_defconfig now has built-in compile support for EXT4 enabled
by default now. So, we can use EXT4 as the default root file system
type for MMC.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
An OMAP specific serial driver was merged on the Linux kenel a long
time ago. So, it makes sense to default the console name to OMAP
ttyO instead of the generic ttyS naming.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:21 +0000 (21:35 +0000)]
da850/omap-l138: Fix NAND flash timings
Though Commit id a3f88293ddd13facd734769c1664d35ab4ed681f (da850evm:
setup the NAND flash timings) has configured the AEMIF timings, they
are not exactly in sync with the timings used in Linux. Linux is
configuring the timing register as 0x08222204, where as currently it
configured to 0x00100084 in U-Boot. This issue was found out when
support for NAND SPL is added in U-Boot. Without this patch U-Boot
does not come up with SPL.
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:20 +0000 (21:35 +0000)]
da850/omap-l138: Add support to read u-boot image from MMC/SD
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
da850/omap-l138: Make MMC and NOR support mutually exclusive
On Logic PD Rev.3 DA850/OMAP-L138 EVM, NOR and MMC/SD cannot
work together. This patch enables the MMC/SD support only
when NOR support is disabled. NOR Flash identification works
even without this patch, but erase and write will have issues.
da850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVM
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When
GP0[11] is low, the SD0 interface will not work, but NOR
flash will. When GP0[11] is high, SD0 will work but NOR
flash will not.
Steve Sakoman [Mon, 4 Jun 2012 05:35:34 +0000 (05:35 +0000)]
omap: am33xx: enable gpio support
This patch uses the code in omap-common to support gpio modules 1-3
on am33xx based boards.
It adds base address and register definitions, enables clocks to the
modules, and enables building the common gpio code for CONFIG_AM33XX
as well as CONFIG_OMAP
Sughosh Ganu [Wed, 13 Jun 2012 08:39:06 +0000 (08:39 +0000)]
hawkboard/omapl-138: Add support for generating ais image for hawkboard
Parameters used for configuring certain SoC peripherals are parsed
from the cfg file and appended as part of the ais image's header. The
u-boot-spl.ais generated is flashed separately to the nand, so do not
delete the file after generation of u-boot.ais.
Ilya Yanok [Fri, 8 Jun 2012 03:12:09 +0000 (03:12 +0000)]
omap24xx_i2c: add 2-byte address support
Various devices like EEPROMs require 2-byte address support to
be properly accessed. This patch adds this support for OMAP2/3/4
I2C controller driver.
I've tested it with EEPROM (16 bit address) and TPS65217 chip
(8 bit address) on TI Beaglebone board.
Unfortunately I don't have access to any compatible hardware
with 16bit data register so I can't test if those #ifdef
clauses really work.
CC: Tom Rini <trini@ti.com> Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Stefan Roese [Thu, 16 Aug 2012 17:55:41 +0000 (17:55 +0000)]
Consolidate bootcount code into drivers/bootcount
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Manfred Rudigier <manfred.rudigier@omicron.at> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de> Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com> Tested-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Sat, 1 Sep 2012 10:22:31 +0000 (12:22 +0200)]
Merge branch 'sf' of git://git.denx.de/u-boot-blackfin
* 'sf' of git://git.denx.de/u-boot-blackfin:
sf: spansion: Add support for S25FL256S
sf: winbond: fix page_size
sf: stmicro: add support for N25Q128A
sf: stmicro: add support N25Q128 parts
sf: stmicro: support JEDEC standard two-byte signature
sf: winbond: add W25Q32
cmd_spi: remove superfluous semicolon
asm/clk.h was included get_peripheral_clk_rate function. But this
is not used from anywhere.
This removed asm/clk.h, and deleted include line from arch/sh/lib/time.c
Scott Wood [Tue, 14 Aug 2012 01:44:29 +0000 (01:44 +0000)]
Makefile: fix HAVE_VENDOR_COMMON_LIB
Commit 8b5a02640adf77301f943e8754992c50df004e8a ("Makefile: cosmetic:
optimize usage of LIBS-y") broke the build of boards that have a board
vendor "common" directory, by introducing a space between "LIBS-" and
"y".
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
Stephen Warren [Mon, 13 Aug 2012 22:46:21 +0000 (16:46 -0600)]
sf: winbond: fix page_size
Commit a4ed3b6 "sf: inline data constants" modified winbond.c's page_size
from 256 to 4096. This prevents either/both of "sf write" writing the
correct data, or "sf read" from reading the correct data back.
This allows U-Boot running on Compulab Tegra to upgrade itself.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Holger Brunck [Thu, 9 Aug 2012 08:22:41 +0000 (10:22 +0200)]
mtd/cfi_flash: fix write problems for Numonyx P33/30 32 MBit flashs
commit 54652991
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips
fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads
to problems for smaller versions of this chip e.g. the 32Mbit version
with deviceid 0x16 on mgcoge. So move the code for this work around to
an own function and check previously manufacturer id and device id to
not break other flashes which don't need this work around.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Philippe De Muyter <phdm@macqel.be>
cc: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Stefan Roese <sr@denx.de>
cfi_flash: add support for Spansion flash PPB sector protection
Erasing flash sectors protected with persistent protection bit (PPB)
mechanism on Spansion flash chips doesn't work. Add sector protection
status checking and sector lock and unlock commands to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Add '-ansi' to DTS_CPPFLAGS to avoid unwanted expansion of dts content
that matches some predefined macros.
Example: A number of PowerPC related *.dts files in the kernel define a
property named 'linux,network-index' which (w/o '-ansi') is expanded to
'1,network-index' by the preprocessor because of '#define linux 1.'
Support for DS1388 is added by extending the DS1337 driver. DS1388 is
similar to DS1337. The time registers are offset by 1 (due to support
for hundreds of seconds), and there is no century bit.
The configuration and trickle charge registers are also different.
Tested on hardware with Freescale P2010 and DS1388.
This should be done in the arch/CPU/SoC specific sub-makefiles to
keep the top Makefiles clean. This patch also allows adding of new
arch/CPU/SoC specific libraries in the future without touching
the top Makefiles.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Stephan Linz [Thu, 2 Aug 2012 18:47:30 +0000 (20:47 +0200)]
sf: stmicro: add support N25Q128 parts
Adds support for Numonyx's N25Q128 SPI flash. These devices
are used on (among others) Avnet Spartan-6 LX9 micro-evaluation
boards. Tested with "sf" commands and CONFIG_ENV_IS_IN_SPI_FLASH.
Signed-off-by: Stephan Linz <linz@li-pro.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Stephan Linz [Thu, 2 Aug 2012 18:47:29 +0000 (20:47 +0200)]
sf: stmicro: support JEDEC standard two-byte signature
There are more than the M25Pxx serial flashs that can be
used with the stmicro driver, for example: the M25PXxx or
N25Qxx serie. All these chips have burned in the original
stmicro manufacture id 0x20 together with a standard
two-byte signature.
In preperation to support all these chips the stmicro driver
have to decode the full two-byte signature.
Signed-off-by: Stephan Linz <linz@li-pro.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
U-Boot port is based on sources forked from GRUB-0.97 by Sun in 2004,
which can be found here:
http://src.opensolaris.org/source/xref/onnv/onnv-gate/usr/src/grub/grub-0.97/stage2/zfs-include/zfs.h
Released by Sun for GRUB under the license:
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
GRUB official releases include ZFS in version:
ftp://alpha.gnu.org/gnu/grub/grub-1.99~rc1.tar.gz
And patched against GRUB Bazaar repository for ashift fixes (4KB HDDs)
more conveniently found at github:
https://github.com/pendor/grub-zfs/commit/e7b6ef3ac3b9685ac4c394c897b1d4221b7381f1
Consider CONFIG_ZERO_BOOTDELAY_CHECK when CONFIG_AUTOBOOT_KEYED is set
When CONFIG_ZERO_BOOTDELAY_CHECK is not defined, bootdelay==0
prevents the check for console input (as stated in README.autoboot).
This must also work in CONFIG_AUTOBOOT_KEYED mode.
Allen Martin [Thu, 19 Apr 2012 07:58:57 +0000 (07:58 +0000)]
mkconfig: add support for SPL CPU
Add support for specifying a differnt CPU for main u-boot and SPL
u-boot builds. This is done by adding an optional SPL CPU after the
main CPU in boards.cfg as follows:
normal_cpu:spl_cpu
This this case CPU will be set to "normal_cpu" during the main u-boot
build and "spl_cpu" during the SPL build.
powerpc:Fix return type & parameter passed for I/O functions
Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32
Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.
Bernhard Walle [Mon, 2 Apr 2012 01:58:34 +0000 (01:58 +0000)]
UBIFS: Improve error message when reading superblock failed
In addition to the error message also display the error code. I had the
problem that my malloc memory was not enough (ENOMEM), and if u-boot
had displayed the error code immediately that would have saved me some
debugging.
Signed-off-by: Bernhard Walle <walle@corscience.de>
Use ubifs_err instead of printf.
Add "errno=%d" in output as suggested by Albert Aribaud.
Simon Glass [Fri, 30 Mar 2012 21:30:56 +0000 (21:30 +0000)]
Allow newlines within command environment vars
Any environment variable can hold commands to be executed by the 'run'
command. The environment variables preboot, bootcmd and menucmd have
special code for triggering execution in certain circumstances.
We adjust these calls to use run_command_list() instead of run_command().
This change permits these variables to have embedded newlines so that
they work the same as the 'source' command.
Simon Glass [Fri, 30 Mar 2012 21:30:55 +0000 (21:30 +0000)]
Add run_command_list() to run a list of commands
This new function runs a list of commands separated by semicolon or newline.
We move this out of cmd_source so that it can be used by other code. The
PXE code also uses the new function.
Suggested-by: Michael Walle <michael@walle.cc> Signed-off-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 29 Mar 2012 09:28:15 +0000 (09:28 +0000)]
Malloc: Fix -Wundef warnings
In file included from arch/arm/lib/board.c:43:0:
include/malloc.h:490:5: warning: "HAVE_MMAP" is not defined [-Wundef]
include/malloc.h:590:5: warning: "HAVE_USR_INCLUDE_MALLOC_H" is not defined [-Wundef]
include/malloc.h:757:5: warning: "HAVE_MMAP" is not defined [-Wundef]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de>
Andy Fleming [Wed, 8 Aug 2012 14:12:30 +0000 (14:12 +0000)]
MAKEALL: Allow empty ERR directory
If we build everything correctly with multiple builds, and an
ERR directory had been previously created, we failed to report
that everything was fine because grep failed to find anything
in the ERR directory. Use grep -r, which doesn't complain if
there are no input files.
Signed-off-by: Andy Fleming <afleming@freescale.com> Tested-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Thu, 9 Aug 2012 19:04:05 +0000 (21:04 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs
powerpc/mpc85xx: Ignore E bit for BSC9130/1
powerpc/sgmii: To support PHY link state auto detect in SGMII mode
powerpc/85xx: improve definition of BR_PHYS_ADDR macro
powerpc/p2041: configure the CPLD lane_mux according to RCW
powerpc/ddr: fix fsl_ddr_get_dimm_params compile error
powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined
powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB
powerpc/p1022ds: fix DIU/LBC switching with NAND enabled
powerpc/p1022ds: add support for SPI and SD boot
Timur Tabi [Wed, 25 Jul 2012 11:03:34 +0000 (11:03 +0000)]
powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs
The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows
which PCI device tree node to look for. The calls to these macros are using a hard-coded string,
but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we
should use that.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
powerpc/sgmii: To support PHY link state auto detect in SGMII mode
PHYs on SGMII riser card are used in SGMII mode with different external
IRQs from eTSEC. This means in SGMII mode phy-handle and phy-connection-type
under ethernet node should be updated. Otherwise the PHY interrupt can not
be handled therefor PHY link state change can not be auto detected.
For we have seperate SGMII PHY nodes, ethernet PHY reg fixup is not needed
but it's still be kept to guarantee the sgmii mode could work with old
device tree.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jia Hongtao <B38951@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shaohui Xie [Thu, 28 Jun 2012 23:37:25 +0000 (23:37 +0000)]
powerpc/p2041: configure the CPLD lane_mux according to RCW
Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.
Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.
Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
fsl_ddr_get_dimm_params() should be wrapped by
CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of
using SPD, it will cause compile error.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shaohui Xie [Thu, 28 Jun 2012 23:35:34 +0000 (23:35 +0000)]
powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined
ENV location compile logic is wrong, and when CONFIG_SYS_NO_FLASH is defined
and non-NOR u-boot is building, it will cause compile error. Also, add
CONFIG_SYS_FLASH_USE_BUFFER_WRITE for p2041, which will improve NOR flash
write performance.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Mon, 21 May 2012 08:43:11 +0000 (08:43 +0000)]
powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation. Early commit eb672e92
works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB.
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Timur Tabi [Fri, 18 May 2012 09:09:09 +0000 (09:09 +0000)]
powerpc/p1022ds: fix DIU/LBC switching with NAND enabled
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.
Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.
Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.
Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Tom Rini [Tue, 7 Aug 2012 16:58:34 +0000 (09:58 -0700)]
ext2fs: fix warning: 'blocknxt' may be used uninitialized with gcc 4.2
The above warning was introduced originally in 436da3c "ext2load:
increase read speed" and fixed for newer toolchains in b803273 "ext2fs:
fix warning: 'blocknxt' may be used uninitialized". This change did not
fix the warning with gcc 4.2, as found in ELDK 4.2.
If we rework the while loop to initalize blocknxt before entering the
warning really goes away. Tested on am335x with an approx 7mb file and
crc32 in U-Boot befor and after this change.
Cc: Wolfgang Denk <wd@denx.de> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Thierry Reding <thierry.reding@avionic-design.de> Cc: Jason Cooper <u-boot@lakedaemon.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Tom Rini <trini@ti.com>
env_onenand: set ONENAND_MAX_ENV_SIZE to CONFIG_ENV_SIZE
This fix prevents env_import() CRC to fail when CONFIG_ENV_SIZE
is not equal to 4096 bytes
It also prevents mtd->read and mtd->write to be incomplete when
the environment is larger than 4096 bytes.
Signed-off-by: David du Colombier <0intro@gmail.com>
mgcoge2ne was an intermediate step towards mgcoge3ne. One difference is the
smaller SDRAM on mgcoge2ne (128MB). To support both boards with the same
u-boot we use here the SDRAM detection.
This patch enables SDRAM detection between 256MB and 128MB.
So in addition to the existing 256MB geometry:
4 chips x 8M (13 rows, 10 cols) x 16 bit x 4 banks
we can now also have 128MB geometry:
4 chips x 4M (13 rows, 9 cols) x 16 bit x 4 banks
This patch adds SDRAM detection feature to km82xx boards.
To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer
for an array of struct sdram_conf_s.
These structs will expose the bitfields within registers PSDMR and OR1 which
have to be different between configurations; common bitfields will be
defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1.
If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained.
projects / u-boot / log