Bin Meng [Fri, 10 Jul 2015 02:51:23 +0000 (10:51 +0800)]
x86: Simplify architecture defined exception handling in irq_llsr()
Instead of using switch..case for architecture defined exceptions,
simply unify the handling by printing a message of exception name,
followed by registers dump then halt the CPU.
With this unification, it also fixes the wrong exception numbers
for #MF/#AC/#MC/#XM which should be 16/17/18/19 not 15/16/17/18.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 10 Jul 2015 02:38:32 +0000 (10:38 +0800)]
x86: Display correct CS/EIP/EFLAGS when there is an error code
Some exceptions cause an error code to be saved on the current stack
after the EIP value. We should extract CS/EIP/EFLAGS from different
position on the stack based on the exception number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 22 Jul 2015 09:03:36 +0000 (11:03 +0200)]
ARM: zynq: DT: Cleanup address-cells and size-cells
Remove unneeded address-cells form intc node because it is already setup
in parent node.
Add missing address-cells and size-cells to eth node to be shared for
every platform DTSes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 22 Jul 2015 08:51:16 +0000 (10:51 +0200)]
ARM: zynq: DT: Use the zynq binding with macb
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do. Also allow the compatible
cadence gem binding that won't disable half duplex but works otherwise.
Michal Simek [Wed, 22 Jul 2015 08:42:51 +0000 (10:42 +0200)]
ARM: zynq: DT: Remove 222 MHz OPP
Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 22 Jul 2015 08:40:51 +0000 (10:40 +0200)]
ARM: zynq: DT: Migrate UART to Cadence binding
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 22 Jul 2015 08:38:45 +0000 (10:38 +0200)]
ARM: zynq: DT: Add a fixed regulator for CPU voltage
To silence the warning
cpufreq_cpu0: failed to get cpu0 regulator: -19
from the cpufreq driver regarding a missing regulator,
add a fixed regulator to the DT.
Zynq does not support voltage scaling and the CPU rail should always be
supplied with 1 V, hence it is added in the SOC-level dtsi.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynq: gem: Increase the Rx buffer descriptors to 32
Increase the Rx Buffer descriptors to 32. This will avoid
Rx buffer descriptors overflow if more packets were received
at one shot before we process the received ones.
This fixes the issue of intermittent timeouts during tftp
on a 1Gb connection with tftp server running on windows.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reproducible U-Boot build support, using SOURCE_DATE_EPOCH
In order to achieve reproducible builds in U-Boot, timestamps that are defined
at build-time have to be somewhat eliminated. The SOURCE_DATE_EPOCH environment
variable allows setting a fixed value for those timestamps.
Simply by setting SOURCE_DATE_EPOCH to a fixed value, a number of targets can be
built reproducibly. This is the case for e.g. sunxi devices.
However, some other devices might need some more tweaks, especially regarding
the image generation tools.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
configs: k2*_evm: rename skernel binary names to generated file names
using http://git.ti.com/keystone-linux/boot-monitor/trees/master as
reference (tag K2_BM_15.07) the generated files do not have evm
extensions by default. So dont use -evm extension.
configs: ti_armv7_keystone2: switch to using kernel zImage
Switch to using zImage instead of uImage. and while at it, start using
bootz as default. While at it, get rid of BOOTIMAGE define and start
using Linux upstream dtb file names.
configs: ti_armv7_keystone2: start using armv7_common
Try to maintain as much commonality by conditionally including stuff
in armv7_common as necessary and removing the common defines from
keystone2 header.
Note: as part of this change, all keystone2 platforms will now start
using the generic u-boot prompt instead of the custom prompt.
Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
configs: ti: armv7_common: enable Thumb mode for all
Commit bd2c4522c26d5 ("ti: armv7: enable EXT support in SPL (using
ti_armv7_common.h)") enabled thumb mode only for SPL builds, however,
All TI armv7 platforms do support thumb, and there is no reason why the
space savings cannot be exploited for u-boot as well.
Reported-by: Murali Karicheri <m-karicheri2@ti.com> Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
configs: split ti_armv7_common into a omap generic header
TI armv7 based SoCs are based on two architectures - one based on OMAP
generation architecture and others based on Keystone architecture.
Many of the options are architecture specific, however a lot are common
with v7 architecture. So, step 1 will be to move out OMAP specific stuff
from ti_armv7_common into a ti_armv7_omap.h header which is then used
by all the relevant architecture headers.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Nishanth Menon <nm@ti.com>
Antonio Borneo [Sun, 19 Jul 2015 14:19:48 +0000 (22:19 +0800)]
stm32f429: use 180 MHz system clock
Mainline Linux kernel commit 338a6aaabc02fa63b70441dd0e1b70aea64673c6 (ARM: dts: Introduce
STM32F429 MCU) in arch/arm/boot/dts/stm32f429.dtsi
requires U-Boot to set system clock to 180 MHz.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl> Cc: u-boot@lists.denx.de
Antonio Borneo [Sun, 19 Jul 2015 14:19:47 +0000 (22:19 +0800)]
stm32f4: add cpu clock option for 180 MHz
While most stm32f4 run at 168 MHz, stm32f429 can work till 180 MHz.
Add option to select 180 MHz through macro CONFIG_SYS_CLK_FREQ.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl> Cc: u-boot@lists.denx.de
Antonio Borneo [Sun, 19 Jul 2015 14:19:46 +0000 (22:19 +0800)]
stm32f429: pass the device unique ID in DTB
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit: 3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl> Cc: u-boot@lists.denx.de
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Simon Glass <sjg@chromium.org>
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
omap-common: SYS_BOOT-based fallback boot device selection for peripheral boot
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
siemens-am33x-common: Hardcoded value instead of non-included define
The config file for the siemens-am33x-common was using OMAP_I2C_STANDARD, which
is defined in a header that is not included in the config header. In most cases,
it was being included by the code using CONFIG_SYS_OMAP24_I2C_SPEED, but it
might not always be the case.
In particular, when introducing I2C SPL support in omap-common's boot-common.c,
the header is missing and including it breaks other devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
omap-common: Common boot code OMAP3 support and cleanup
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
kbuild: create symbolic link only for ARM, AVR32, SPARC, PowerPC, x86
The symbolic link to SoC/CPU specific header directory is created
during the build, while it is only necessary for ARM, AVR32, SPARC,
x86, and some CPUs of PowerPC. For the other architectures, it just
results in a broken symbolic link.
Introduce CONFIG_CREATE_ARCH_SYMLINK to not create unneeded symbolic
links.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generic_board: Call "checkboard" even though the root node has a "model" property
In case of enable CONFIG_OF_CONTROL and has a "model" property in the root node,
the board special "checkboard" will not be called.
Usually we show some useful version information in the function.
This patch enable call "checkboard" in any case.
It is not conflicting with showing "model" at the same time.
For example on LS2085AQDS:
Showing "model" only:
Model: Freescale Layerscape 2085a QDS Board
keystone2: net: add mcast function to keyston2 Ethernet driver
The MCAST_TFTP support requires that network drivers has mcast functon
implemented. This commit adds dummy keystone2_eth_bcast_addr() to meet
the requirement. As far as the driver doesn't use ALE and doesn't filter
any incoming packets, the function is empty.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When core A turning of core B, via tetris DPSC it places the core
B DPSC into transitional state. The core B has to execute wfi instruction
to move its DPSC to the OFF state. This patch add such instruction.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Stefan Roese [Mon, 6 Jul 2015 11:35:55 +0000 (13:35 +0200)]
misc: led: pca9551_led: Fix problem with multiple blink frequencies
Only 2 frequencies are supported. The current driver implementation does
not always use the 2 last configured blink frequencies. This patch
fixes this problem. So that the last two entered frequencies are
active.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Tom Rini <trini@konsulko.com>
kbuild: use relative path more to include Makefile
Prior to this commit, it was impossible to use relative path to
include Makefiles from the top level Makefile because the option
"--include-dir=$(srctree)" becomes effective when Make enters into
sub Makefiles.
To use relative path in any places, this commit moves the option
above the "sub-make" target.
This was imported from Linux (commit a436bb7b8063) and adjusted for
U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Marek <mmarek@suse.cz>
Update some build scripts to match Linux 4.1. Commit-based syncing
was done so as not to break U-Boot specific changes.
The previous big sync was from Linux 3.18-rc1 by commit 176d09827725
(kbuild: sync misc scripts with Linux 3.18-rc1).
The commits imported from Linux (some with adjustments) are:
[7] commit d0d38cd9e853db11e0242b3df4c9c3c4a663fbb4
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: use mixed-targets when two or more config targets are given
[9] commit 665d92e38f65d70796aad2b8e49e42e80815d4a4
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: do not add $(call ...) to invoke cc-version or cc-fullversion
[10] commit 6dcb4e5edf39e3b65a75ca76f087b2fdbee8a808
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: allow cc-ifversion to have the argument for false condition
Update the files under scripts/kconfig/ to match Linux 4.1.
Some Kconfig sources have diverged from those in the kernel,
so commit-base syncing was done not to lose U-Boot specific updates.
config: ti_omap5_common: Palmas power support in SPL
Palmas power support is required for OMAP5 devices such as the OMAP5 uEVM, that
need to e.g. enable MMC power at SPL stage.
This is especially important when booting from a peripheral (such as USB, UART),
where the bootrom will not enable power for the MMC device that will hold the
main U-Boot.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
Hans de Goede [Thu, 18 Jun 2015 16:19:22 +0000 (18:19 +0200)]
sunxi: Enable both ehci and otg in host mode on various boards
Now that the device-model port of the musb mode makes it possible, enable
both the ehci and otg in host mode on boards where the musb is wired up in
host only mode, either via an usb-a receptacle or via an usb <-> sata
converter.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Thu, 18 Jun 2015 16:21:33 +0000 (18:21 +0200)]
sunxi: musb: Stop treating not having a vbus-det gpio as an error
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 17 Jun 2015 15:44:58 +0000 (17:44 +0200)]
sunxi: musb: Use device-model for musb host mode
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 17 Jun 2015 13:49:26 +0000 (15:49 +0200)]
sunxi: musb: Move musb config and platdata to the sunxi-musb glue
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 14 Jun 2015 15:40:37 +0000 (17:40 +0200)]
sunxi: musb: Add id pin support
When in host mode check if there is a host cable inserted into the otg
port by checking the id pin. If there is no host cable return an error to
make usb_lowlevel_init() exit early, rather then waiting for 1 second
for a device which will never show up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 17 Jun 2015 18:54:07 +0000 (20:54 +0200)]
sunxi: Enable CMD_USB and USB_STORAGE by default on sunxi
Start using the new Kconfig options which are available for these now,
and simply always enable them by selecting them as sunxi builds always
include USB support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 30 Jun 2015 20:51:15 +0000 (16:51 -0400)]
sunxi: Update selects in arch/arm/Kconfig for DM conversions
With certain features being convert to DM now we want sunxi to default
to having DM enabled for ETH/SERIAL and USB in some cases.
Cc: Hans de Goede <hdegoede@redhat.com> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Tom Rini <trini@konsulko.com>
[hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Simon Glass <sjg@chromium.org>
Rob Herring [Fri, 24 Jul 2015 15:14:21 +0000 (10:14 -0500)]
usb: ci_udc: fix request allocation when endpoints are disabled
The ci_udc driver request allocation assumes that the endpoint descriptor
pointer is set to retrieve the endpoint number, but that is only true
when the endpoint is enabled. This results in a NULL ptr dereference
which for me happens to return 0 value. This causes the EP0 request
struct to be returned for other endpoints. Some gadget drivers like
fastboot and USB MS work fine, but ethernet does not.
Really, the ci_udc driver is the oddball here doing this EP0 special
case handling Stephen added. All the other drivers alloc/free functions
are pretty much the same with the only variation being the size of the
private struct. This could all be consolidated to a common function.
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Marek Vasut <marex@denx.de> Acked-by: Stephen Warren <swarren@nvidia.com>
sunxi: spl: Remove redundant check from `board_mmc_init` for signature
Remove the boot signature check from board_mmc_init() in spl mode, as it
is already done in spl_boot_device() in this case, and update the comments
to reflect this.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu> CC: Roy Spliet <r.spliet@ultimaker.com> Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Disable the check only for SPL instead of always] Acked-by: Hans De Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: spl: Detect at runtime where SPL was read from
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu> CC: Roy Spliet <r.spliet@ultimaker.com> Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes] Acked-by: Hans De Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: Create helper function veryfing valid boot signature on MMC
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.
Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu> CC: Roy Spliet <r.spliet@ultimaker.com> Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
projects / u-boot / log