Stefan Roese [Tue, 14 Aug 2007 12:41:55 +0000 (14:41 +0200)]
POST: Add option for external ethernet loopback test
When CFG_POST_ETHER_EXT_LOOPBACK is defined, the ethernet POST
is not done using an internal loopback connection, but by assuming
that an external loopback connector is plugged into the board.
This series of patches adds support for 2 boards from Netstal Maschinen.
The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.
The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.
The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.
This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.
[ppc440SPe] Graceful recovery from machine check during PCIe configuration
During config transactions on the PCIe bus an attempt to scan for a
non-existent device can lead to a machine check exception with certain
peripheral devices. In order to avoid crashing in such scenarios the
instrumented versions of the config cycle read routines are introduced, so
the exceptions fixups framework can gracefully recover.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com> Acked-by: Rafal Jaworowski <raj@semihalf.com>
[ppc4xx] Separate settings for PCIe bus numbering on 440SPe rev.A
This brings back separate settings for PCIe bus numbers depending on chip
revision, which got eliminated in 2b393b0f0af8402ef43b25c1968bfd29714ddffa
commit. 440SPe rev. A does NOT work properly with the same settings as for
the rev. B (no devices are seen on the bus during enumeration).
Changed storage type of cfg_simulate_spd_eeprom to const
Changed storage type of gpio_tab to stack storage
(Cannot access global data declarations in .bss until afer code relocation)
Improved SDRAM tests to catch problems where data is not uniquely addressable
(e.g. incorrectly programmed SDRAM row or columns)
Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
Fixed AM29LV320DT (OpCode Flash) sector map
Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com> Signed-off-by: Stefan Roese <sr@denx.de>
Change Lime SDRAM initialization to now support 100MHz and
133MHz (if enabled). Also the framebuffer is initialized to
display a blue rectangle with a white border.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 16 Jul 2007 06:53:51 +0000 (08:53 +0200)]
ppc4xx: Add remove_tlb() function to remove a mem area from TLB setup
The new function remove_tlb() can be used to remove the TLB's used to
map a specific memory region. This is especially useful for the DDR(2)
setup routines which configure the SDRAM area temporarily as a cached
area (for speedup on auto-calibration and ECC generation) and later
need this area uncached for normal usage.
[PCS440EP] - Show on the DIAG LEDs, if the SHA1 check failed
- now the Flash ST M29W040B is supported (not tested)
- fix the "led" command
- fix compile error, if BUILD_DIR is used
Stefan Roese [Wed, 4 Jul 2007 08:06:30 +0000 (10:06 +0200)]
ppc4xx: Update lwmon5 board
- Add optional ECC generation routine to preserve existing
RAM values. This is needed for the Linux log-buffer support
- Add optional DDR2 setup with CL=4
- GPIO50 not used anymore
- Lime register setup added
Stefan Roese [Mon, 25 Jun 2007 13:57:39 +0000 (15:57 +0200)]
ppc4xx: Add pci_pre_init() for 405 boards
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Matthias Fuchs [Sun, 24 Jun 2007 15:23:41 +0000 (17:23 +0200)]
ppc4xx: Add pci_pre_init() for 405 boards
This patch adds support for calling a plattform dependant
pci_pre_init() function for 405 boards. This can be used to
move the current pci_405gp_fixup_irq() function into the
board code.
This patch also makes the CFG_PCI_PRE_INIT define obsolete.
A default function with 'weak' attribute is used when
a board specific pci_pre_init() is not implemented.
Igor Lisitsin [Wed, 18 Apr 2007 10:55:19 +0000 (14:55 +0400)]
Adapt log buffer code to support Linux 2.6
A new environment variable, "logversion", selects the log buffer
behaviour. If it is not set or set to a value other than 2, then the
old, Linux 2.4.4, behaviour is selected.
Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--
Heiko Schocher [Fri, 22 Jun 2007 17:11:54 +0000 (19:11 +0200)]
[PCS440EP] upgrade the PCS440EP board:
- Show on the Status LEDs, some States of the board.
- Get the MAC addresses from the EEProm
- use PREBOOT
- use the CF on the board.
- check the U-Boot image in the Flash with a SHA1
checksum.
- use dynamic TLB entries generation for the SDRAM
Stefan Roese [Fri, 22 Jun 2007 14:58:40 +0000 (16:58 +0200)]
ppc4xx: Fix problem with extended program_tlb() funtion
The recently extended program_tlb() function had a problem when
multiple TLB's had to be setup (for example with 512MB of SDRAM). The
virtual address was not incremented. This patch fixes this issue
and is tested on Katmai with 512MB SDRAM.
Stefan Roese [Tue, 19 Jun 2007 15:22:44 +0000 (17:22 +0200)]
ppc4xx: Add bootstrap command for AMCC Sequoia (440EPx) eval board
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 533 nor ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand ;to configure the board for 667MHz NNAND booting
Stefan Roese [Tue, 19 Jun 2007 14:42:31 +0000 (16:42 +0200)]
[ppc4xx] Fix problem with NAND booting on AMCC Acadia
The latest changes showed a problem with the location of the NAND-SPL
image in the OCM and the init-data area (incl. cache). This patch
fixes this problem.
Stefan Roese [Thu, 14 Jun 2007 09:14:32 +0000 (11:14 +0200)]
[ppc4xx] Extend program_tlb() with virtual & physical addresses
Now program_tlb() allows to program a TLB (or multiple) with
different virtual and physical addresses. With this change, now one
physical region (e.g. SDRAM) can be mapped 2 times, once with caches
diabled and once with caches enabled.
Stefan Roese [Wed, 6 Jun 2007 09:42:13 +0000 (11:42 +0200)]
ppc4xx: Add NAND booting support for AMCC Acadia (405EZ) eval board
This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.
I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND booting
Ed Swarthout [Tue, 5 Jun 2007 17:30:52 +0000 (12:30 -0500)]
mpc8641 image size cleanup
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variable
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
projects / u-boot / log