Use "setter" functions instead of flags, cleaner and more flexible.
It also fixes the problem noted by Timur Tabi that the ethernet MAC
addresses were all being set incorrectly to the same MAC address.
In bootm, create the "/chosen" node only if it doesn't already exist
(better matches the previous behavior).
Update for proper reserved memory map handling for initrd.
Driver for the Atmel MACB on-chip ethernet controller.
This driver has been tested on the ATSTK1000 board with a AT32AP7000
CPU. It should probably work on AT91SAM926x as well with some minor
modifications.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
AVR32: Add clk and gpio infrastructure for macb0 and macb1
Implement functions for configuring the macb0 and macb1 pins, as
well as functions for getting the clock rate of the various
busses the macb ethernet controllers are connected to.
Include the imi, imls and jffs commands sets by default on ATSTK1000.
Also define CONFIG_BOOTARGS to something more useful, define
CONFIG_BOOTCOMMAND and enable autoboot by default.
AVR32: Use initdram() instead of board_init_memories()
Conform to the "standard" interface and use initdram() instead of
board_init_memories() on AVR32. This enables us to get rid of the
sdram_size member of the global_data struct as well.
Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.
As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.
Add -fPIC -mno-init-got to the avr32-specific CFLAGS to make u-boot
position independent. This will make relocation a lot easier.
-mno-init-got means that gcc shouldn't emit code to load the GOT
address into r6 in every function prologue. We do it once and for
all in the early startup assembly code, so enabling this option
makes u-boot a bit faster and smaller.
The assembly parts have always been position-independent, so no code
changes should be necessary.
AVR32: Split start_u_boot into board_init_f and board_init_r
Split the avr32 initialization code into a function to run before
relocation, board_init_f and a function to run after relocation,
board_init_r. For now, board_init_f simply calls board_init_r
at the end.
Denis Peter [Fri, 13 Apr 2007 07:13:33 +0000 (09:13 +0200)]
[PATCH] Fix bugs in cmd_ide.c and cmd_scsi.c
Fix bug introduced by "Fix get_partition_info() parameter error in all
other calls" from 2005-03-04 in cmd_ide.c and cmd_scsi.c, which prevented
to use diskboot or scsiboot form another device than 0.
Jeffrey Mann [Thu, 12 Apr 2007 12:15:59 +0000 (14:15 +0200)]
ppc4xx: Fix i2c divisor calcularion for PPC4xx
This patch fixes changes the i2c_init(...) function to use the function
get_OPB_freq() rather than calculating the OPB speed by
sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is
specific per processor. The prior method was not and so was calculating
the wrong speed for some PPC4xx processors.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com> Signed-off-by: Stefan Roese <sr@denx.de>
Haiying Wang [Mon, 22 Jan 2007 18:37:30 +0000 (12:37 -0600)]
Add PIXIS FPGA support for MPC8641HPCN board.
Move the 8641HPCN's PIXIS code to the new directory
board/freescale/common/ as it will be shared by
future boards not in the same processor family.
Write a "pixis_reset" command that utilizes the FPGA
reset sequencer to support alternate soft-reset options
such as using the "alternate" flash bank, enabling
the watch dog, or choosing different CPU frequencies.
Add documentation for the pixis_reset to README.mpc8641hpcn.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
Stefan Roese [Mon, 2 Apr 2007 08:09:30 +0000 (10:09 +0200)]
ppc4xx: Change SysACE address on Katmai
With this new base address of the Xilinx SystemACE controller
the Linux driver will be easier to adapt, since it can now be
mapped via the "normal" ioremap() call.
Gerald Van Baren [Sat, 31 Mar 2007 16:22:10 +0000 (12:22 -0400)]
Add a flattened device tree (fdt) command (1 of 2)
The fdt command uses David Gibson's libfdt library to manipulate as well
as print the flattened device tree. This patch is the new command,
the second part is the modifications to the existing code.
Gerald Van Baren [Sat, 31 Mar 2007 16:13:43 +0000 (12:13 -0400)]
libfdt: Enhanced and published fdt_next_tag()
Enhanced the formerly private function _fdt_next_tag() to allow stepping
through the tree, used to produce a human-readable dump, and made
it part of the published interface.
Also added some comments.
Stefan Roese [Sat, 31 Mar 2007 06:46:08 +0000 (08:46 +0200)]
ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
Fix a bug in the auto calibration routine. This driver now runs
more reliable with the tested modules. It's also tested with
167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai.
Stefan Roese [Wed, 28 Mar 2007 12:52:12 +0000 (14:52 +0200)]
i2c: Enable "old" i2c commands even when CONFIG_I2C_CMD_TREE is defined
The "old" i2c commands (iprobe, imd...) are now compiled in again,
even when the i2c command tree is enabled via the CONFIG_I2C_CMD_TREE
config option.
Haiying Wang [Thu, 7 Dec 2006 16:35:55 +0000 (10:35 -0600)]
Set Rev 2.x 86xx PIC in mixed mode.
Prevent false interrupt from hanging Linux as MSR[EE] is set
to enable interrupts by changing the PIC out of the default
pass through mode into mixed mode.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
projects / u-boot / log