Robert Winkler [Thu, 2 Oct 2014 19:16:31 +0000 (12:16 -0700)]
nitrogen6x: display: add support lvds jeida screen
Add support for Boundary Devices 7" and 10.1" 1280x800 displays with
integrated FocalTech ft5x06 10-point touch controller.
Because they share the touch controller with the 1024x600 displays,
auto-detection is disabled and you must explicitly set the 'panel'
environment variable:
Eric Nelson [Thu, 2 Oct 2014 19:16:27 +0000 (12:16 -0700)]
nitrogen6x: staticize board file
Declare locally-used data structures and functions as
static and pull in header files to prevent compiler warnings
of "Should it be static?" when building with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Eric Nelson [Thu, 2 Oct 2014 19:16:22 +0000 (12:16 -0700)]
nitrogen6x: implement board_cfb_skip() to disable text output
Several customers have asked to leave the display quiet during
boot, so allow the user to express this request by the presence
of environment variable "novideo".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
imx: mx6dlarm2: Add support for i.MX6Q/DL arm2 LPDDR2 boards
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
imx: mx6dlarm2: Add support for i.MX6DL arm2 DDR3 board
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2
shared the same board with i.MX6Q ARM2 board since the i.MX6DL is
pin-pin compatible with i.MX6Q.
The patch also support the DDR 32-BIT mode option. Please define
CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT
mode.But due to the board design, it's 64bit DDR buswidth physically,
so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it.
usb: ehci-mx6: Rename the USB register base address
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name
"USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes
the USB base address name to "USBOH3", which causes the driver
failed to build for mx6sl/mx6sx.
This patch uniform the address name to "USB_BASE_ADDR" for all
mx6 series.
imx: mx6: Checking PLL2 PFD0 and PFD2 for periph_clk before PFD reset
Checking the pre_periph_clk_sel and pre_periph2_clk of CCM CBCMR
register, if the PLL2 PFD0 or PLL2 PFD2 is used for the clock source,
do not reset this PFD to avoid system hang. Customers may set this
in DDR script or use BT_FREQ to select low freq boot.
Marek Vasut [Mon, 28 Apr 2014 01:38:43 +0000 (03:38 +0200)]
arm: mxs: olinuxino: Fine-tune DRAM configuration
Add fine-tuning for the DRAM configuration according to the DRAM chip
datasheet. THis configuration applies to both Hynix HY5DU12622DTP and
Samsung K5H511538J-D43 .
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Mon, 28 Apr 2014 01:38:41 +0000 (03:38 +0200)]
arm: mxs: Wait for DRAM to start
Instead of waiting for a fixed period of time and hoping for the best
that the DRAM will start, read back an EMI status register which tells
us exactly when the DRAM started.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Mon, 28 Apr 2014 01:38:40 +0000 (03:38 +0200)]
arm: mxs: Wait when disabling VDDMEM current limiter
According to i.MX23 datasheet Table 32-17, we must wait for the supply
to settle before disabling the current limiter. Indeed, not waiting a
little here causes the system to crash at times.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Mon, 28 Apr 2014 01:38:39 +0000 (03:38 +0200)]
usb: ehci: mxs: Add board-specific callbacks
Add board-specific callbacks for enabling/disabling port power
into the MXS EHCI controller driver. This is in-line with the
names of callbacks on other systems.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
imx: Support i.MX6 High Assurance Boot authentication
When CONFIG_SECURE_BOOT is enabled, the signed images
like kernel and dtb can be authenticated using iMX6 CAAM.
The added command hab_auth_img can be used for HAB
authentication of images. The command takes the image
DDR location, IVT (Image Vector Table) offset inside
image as parameters. Detailed info about signing images
can be found in Freescale AppNote AN4581.
imx: ddr: Move mx6q_4x_mt41j128.cfg to mx6sabresd board
Provide cgtqmx6eval board its own variant of ddr
setup config file. Move board/freescale/imx/ddr/
mx6q_4x_mt41j128.cfg to board/freescale/mx6sabresd/
as this is was designed for the mx6sabresd board.
imx: nitrogen6x: Make use of both uSD and SD slots to load script or kernel on Sabrelite board
Sabrelite board has two solts: 0 is SD3 (bottom) slot and 1 is uSD4 (top) slot.
This patch makes use of both slots instead of only one.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com> Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Bo Shen [Fri, 1 Aug 2014 08:37:09 +0000 (16:37 +0800)]
ARM: atmel: sama5d3: add timings register
Signed-off-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 18 Jul 2014 08:43:07 +0000 (16:43 +0800)]
ARM: atmel: sama5d3xek: add nor flash init function
Add NOR flash hardware init function, including SMC and PIO
configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wu, Josh [Tue, 24 Jun 2014 10:18:06 +0000 (18:18 +0800)]
mtd: atmel-nand: use pmecc_readl(b)/pmecc_writel to access the pmecc register
We defined the macro pmecc_readl(b)/pmecc_writel for pmecc register access.
But in the driver we also use the readl(b)/writel.
To keep consistent, this patch make all use pmecc_readl(b)/pmecc_writel.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
OMAP4: Use generic 'load' command instead of 'fatload' for 'loadbootscript' and 'loadbootenv' as already done for 'loadimage' and 'loaduimage'.
This patch uses generic 'load' command instead of 'fatload' for 'loadbootscript' and 'loadbootenv' as already done for 'loadimage' and 'loaduimage' for OMAP4 boards.
This allows to use EXT partition instead of FAT, while keeping FAT compatibility.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@ti.com>
ARM: keystone: ddr3: workaround for ddr3a/3b memory issue
This patch implements a workaround to fix DDR3 memory issue.
The code for workaround detects PGSR0 errors and then preps for
and executes a software-controlled hard reset.In board_early_init,
where logic has been added to identify whether or not the previous
reset was a PORz. PLL initialization is skipped in the case of a
software-controlled hard reset.
Tom Rini [Tue, 16 Sep 2014 15:08:46 +0000 (11:08 -0400)]
Revert "ARM: SPL: do not set gd again"
At the high level, the problem is that we set gd multiple times (and
still do, even after the commit we're reverting). We set important
parts of gd to the copy which is not above stack but rather in the data
section. For the release, we're going to revert this change and for the
next release we shall correct things to only, really, set gd once to an
appropriate location and ensure that comments about it are correct too.
Gerhard Sittig [Fri, 12 Sep 2014 06:48:15 +0000 (08:48 +0200)]
net: dns: fix for DNS queries sent to the wrong MAC address
When a DNS query is sent out, the ethernet packet can get directed to
the MAC address of a server that was communicated to before. This is
wrong when the previously stored MAC address corresponds to a different
server's IP address, i.e. when the IP address of the previous and the
current communication are different.
The error can get reproduced by running a sequence of e.g. a TFTP
download and a DNS query, where the TFTP and DNS servers reside on
individual machines.
The fix is to clear the server's MAC address that might be left from a
previous operation, and to fetch the peer's MAC address in a new ARP
lookup, before the DNS query is sent. This is the approach taken in
other network services, like 8e52533d1095 ("net: tftpsrv: Get correct
client MAC address").
Reported-by: Dirk Zimoch <dirk.zimoch@psi.ch> Signed-off-by: Gerhard Sittig <gsi@denx.de>
For the SPL configuration, "make <dir>/<target>" is used.
Here,
<dir> is either "spl" or "tpl"
<target> is one of "config", "menuconfig", "xconfig", etc.
This commit adds two checks:
[1] If <dir> is given an unsupported subimage, the configuration
should error out like this:
$ make qpl/menuconfig
***
*** "make qpl/menuconfig" is not supported.
***
[2] Make sure that "CONFIG_SPL" is enabled in the ".config" before
running "make spl/menuconfig. Otherwise, the SPL image
is not built at all. Having "spl/.config" makes no sense.
In such a case, the configuration should exit with a message:
$ make spl/menuconfig
***
*** Create ".config" with "CONFIG_SPL" enabled
*** before "make spl/menuconfig".
***
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Simon Glass <sjg@chromium.org>
It's not clear who actually moved this code, or whether the kernel was the
original source, or somewhere else, but it probably should still have the
SMSC copyright.
mtd: nand: davinci_nand: update write_page function for keystone RBL
After mtd was synced with Linux 3.14
(ff94bc40af3481d47546595ba73c136de6af6929)
the number of parameters for write_page function of nand_chip was
changed. The additional two var were needed for subpage write.
As keystone has no supbage write they are not needed. So correct
only function definition by upgrading it's parameter list.
That helps to get ritd of compilation warning.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Gabriel Huau [Wed, 3 Sep 2014 20:57:54 +0000 (13:57 -0700)]
common: fix include guards for CONFIG_MP
This was breaking the build for some boards:
MPC8536DS MPC8536DS_36BIT MPC8536DS_SDCARD MPC8536DS_SPIFLASH qemu-ppce500
Include only these features for some PPC boards if the configuration for MultiProcessor
is enabled.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr> Cc: Tom Rini <trini@ti.com> Cc: York Sun <yorksun@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Since 3ff291f371fa9858426774f3732924bacb61ed1c
(kconfig: convert Kconfig helper script into a shell script),
"make config" is not working because of a missing '$' before '(Q)'.
Besides, "make config" should be invoked via scripts/multiconfig.sh
to avoid a warning message:
Kconfig:11:warning: environment variable KCONFIG_OBJDIR undefined
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
kconfig: fix savedefconfig to handle TPL correctly
Since 3ff291f371fa9858426774f3732924bacb61ed1c
(kconfig: convert Kconfig helper script into a shell script),
"make savedefconfig" of TPL boards has not been working.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.o.rg Acked-by: Simon Glass <sjg@chromium.org>
standalone: use GCC_VERSION defined in compiler-gcc.h
Now GCC_VERSION is defined in include/linux/compiler-gcc.h
(with a little different definition).
Use it and delete the one in examples/standlone/stub.c.
This should work on Clang too because __GNUC__, __GNUC_MINOR__,
__GNUC_PATCHLEVEL__ are also defined on Clang.
Steve Rae [Wed, 3 Sep 2014 17:05:51 +0000 (10:05 -0700)]
add code to handle Android sparse image format
Add original file (pristine) from :
https://www.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=master
[3b5092d20bd15a7a2879c13e9f64acc48d04af2d]
Peng Fan [Mon, 1 Sep 2014 13:48:07 +0000 (21:48 +0800)]
kgdb: Remove first_entry for kgdb
There are two ways to run into handle_exception, run command 'kgdb' and
encounter a breakpoint which triggers exception handling.
The origin source code only saves regs when first run command 'kgdb'.
Take the following for example, When run 'kgdb', regs is saved to entry_regs.
When run 'bootz', regs is not saved. However, if we set a breakpoint, then
continue. When breakpoint is reached, run `quit`, and Now return to the
instruction which follows kgdb, but not bootz.This may cause errors. So,
save regs for each handle_exception call to return to the correct place.
Example:
Target | Host
=>kgdb | (gdb)b bootz
| (gdb)c
=>bootz |
| (gdb)Here stop because of breakpoint
| (gdb)q
tools/genboardscfg.py: improve performance more with Kconfiglib
The idea of using Kconfiglib was given by Tom Rini.
It allows us to scan lots of defconfigs very quickly.
This commit also uses multiprocessing for further acceleration.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
Thierry Reding [Thu, 28 Aug 2014 10:38:03 +0000 (12:38 +0200)]
rtl8169: Defer network packet processing
When network protocol errors occur (such as a file not being found on a
TFTP server), the processing done by the NetReceive() function will end
up calling the driver's .halt() implementation. However, after that the
device no longer has access to the memory buffers and will cause errors
such as this in the rtl_recv() function when trying to hand descriptors
back to the device:
pci_hose_bus_to_phys: invalid physical address
This can be fixed by deferring processing of network packets until the
descriptors have been handed back. That way rtl_halt() tearing down
network buffers is not going to prevent access to the buffers.
Reported-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Peng Fan [Mon, 15 Sep 2014 06:59:17 +0000 (14:59 +0800)]
imx:mx6qarm2: change CONFIG_SYS_FSL_ESDHC_ADDR
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC4_BASE_ADDR.
USDHC3 and USDHC4 are both initialized in board_mmc_init. There is
no restriction on USDHC3 addr or USDHC4 addr should be assigned to
CONFIG_SYS_FSL_ESDHC_ADDR. So, just choose USDHC4_BASE_ADDR to avoid
errors when fsl_esdhc_mmc_init is invoked.
Stefan Agner [Fri, 12 Sep 2014 11:06:36 +0000 (13:06 +0200)]
arm: vf610: add NAND support for vf610twr
This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).
Stefan Agner [Fri, 12 Sep 2014 11:06:35 +0000 (13:06 +0200)]
mtd: nand: add Freescale vf610_nfc driver
This adds initial support for Freescale NFC (NAND Flash Controller)
found in ARM Vybrid SoC's, Power Architecture MPC5125 and others.
The driver is called vf610_nfc since this is the first supported
and tested hardware platform supported by the driver.
Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Andrew Ruder [Tue, 12 Aug 2014 14:26:01 +0000 (09:26 -0500)]
arm: mx35: use common timer functions
This patch moves mx35 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx35 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx35 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
Andrew Ruder [Tue, 12 Aug 2014 14:26:00 +0000 (09:26 -0500)]
arm: mx31: use common timer functions
This patch moves mx31 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx31 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx31 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Cc: Marek Vasut <marex@denx.de> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Wolfgang Denk <wd@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Helmut Raiger <helmut.raiger@hale.at>
projects / u-boot / log