Mike Frysinger [Fri, 8 Jan 2010 13:03:06 +0000 (08:03 -0500)]
jffs2: fix hangs/crashs when not using CONFIG_JFFS2_PART_SIZE
Commit b5b004ad8a0ac6f98bd5708ec8b22fbddd1c1042 caused the sector_size to
be calculated incorrectly when the part size was not hardcoded. This is
because the new code relied on part->size but tried to do the calculation
before it was initialized properly, and it did not take into consideration
the magic SIZE_REMAINING define.
Mike Frysinger [Fri, 22 Jan 2010 00:59:04 +0000 (19:59 -0500)]
tools: give explicit libfdt paths
The current libfdt object rules hard depend implicitly on the .depend file
being correct. If it isn't, then it is unable to properly compile the
objects. Give it a full path like all the other implicit rules here so it
will always work in face of .depend issues.
Mike Frysinger [Fri, 22 Jan 2010 00:30:36 +0000 (19:30 -0500)]
gzip/zlib: make features optional
If you really want to slim down U-Boot and you would rather use a higher
compression scheme (like LZMA), it'd be nice to disable gzip/zlib since
these code bases take up a significant amount of space.
Stefano Babic [Wed, 20 Jan 2010 17:19:10 +0000 (18:19 +0100)]
mkimage: Add Freescale imx Boot Image support (imximage)
This patch adds support for "imximage" (MX Boot Image)
to the mkimage utility. The imximage is used on the Freescales's
MX.25, MX.35 and MX.51 processors.
Further details under doc/README.imximage.
This patch was tested on a Freescale mx51evk board.
Detlev Zundel [Fri, 22 Jan 2010 13:47:59 +0000 (14:47 +0100)]
mpc512x: Add display of reset status register
Content of the RSR is put into gd early so we can output it together
with the CPU info. The clearing of gd in board_init_f is redundant for
this architecture as it is done in cpu_init_f so we remove it.
Normally the processor clock has a divisor of 2.
In some cases this this needs to be set to 4.
Check the user has set environment mdiv to 4 to change the divisor.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Vipin KUMAR [Fri, 15 Jan 2010 13:45:53 +0000 (19:15 +0530)]
SPEAr : Support added for SPEAr320 board
SPEAr320 SoC support contains basic spear320 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Vipin KUMAR [Fri, 15 Jan 2010 13:45:52 +0000 (19:15 +0530)]
SPEAr : Support added for SPEAr310 board
SPEAr310 SoC support contains basic spear310 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Vipin KUMAR [Fri, 15 Jan 2010 13:45:50 +0000 (19:15 +0530)]
SPEAr : Support added for SPEAr300 board
SPEAr300 SoC support contains basic spear300 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Vipin KUMAR [Fri, 15 Jan 2010 13:45:49 +0000 (19:15 +0530)]
SPEAr : Support for HW mac id read/write from i2c mem
This patch adds the support to read and write mac id from i2c
memory.
For reading:
if (env contains ethaddr)
pick env ethaddr
else
pick ethaddr from i2c memory
For writing:
chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
in i2c memory
Vipin KUMAR [Fri, 15 Jan 2010 13:45:48 +0000 (19:15 +0530)]
SPEAr : Support added for SPEAr600 board
SPEAr600 SoC support contains basic spear600 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Vipin KUMAR [Fri, 15 Jan 2010 13:45:47 +0000 (19:15 +0530)]
SPEAr : usbd driver support for SPEAr SoCs
SPEAr SoCs contain a synopsys usb device controller.
USB Device IP can work in 2 modes
- DMA mode
- Slave mode
The driver adds support only for slave mode operation of usb
device IP. This driver is used along with standard USBTTY
driver to obtain a tty interface over USB on the host
Vipin KUMAR [Fri, 15 Jan 2010 13:45:46 +0000 (19:15 +0530)]
SPEAr : nand driver support for SPEAr SoCs
SPEAr SoCs contain an FSMC controller which can be used to interface
with a range of memories eg. NAND, SRAM, NOR.
Currently, this driver supports interfacing FSMC with NAND memories
Vipin KUMAR [Fri, 15 Jan 2010 13:45:45 +0000 (19:15 +0530)]
SPEAr : smi driver support for SPEAr SoCs
SPEAr SoCs contain a serial memory interface controller. This
controller is used to interface with spi based memories.
This patch adds the driver for this IP.
Kirkwood: Upgated licencing for files imported from linux source to GPLv2 or later
These are few files directly imported from Linux kernel source.
Those are not modifyed at all ar per strategy.
These files contains source with GPLv2 only
whereas u-boot expects GPLv2 or latter
These files are updated for the same from prior permission from original writes
Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Seunghyeon Rhee [Thu, 3 Dec 2009 00:41:49 +0000 (09:41 +0900)]
samsung: fix DMC1_MEM_CFG for s3c64xx
The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control
for S3C6400. In the configuration of SMDK6400, however, two 16-bit
mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit
memory bus and there is no need to control CKE for each chip
separately. AFAIK, CKE1 is not at all connected. Only CKE0 is
used. Futhermore, it should be '0' always for S3C6410. When tested
with a board which has a S3C6410 and the same memory configuration,
a side effect is observed that u-boot command "reset" doesn't work
leading to system hang. Leaving the bit clear is safe in most cases.
Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Stefan Roese [Thu, 21 Jan 2010 10:37:31 +0000 (11:37 +0100)]
ppc4xx: Kilauea: Add CPLD version detection and EBC reconfiguration
A newer CPLD version on the 405EX evaluation board requires a different
EBC controller setup for the CPLD register access. This patch adds a CPLD
version detection for Kilauea and code to reconfigure the EBC controller
(chip select 2) for the old CPLD if no new version is found.
Additionally the CPLD version is printed upon bootup:
Felix Radensky [Fri, 22 Jan 2010 23:35:24 +0000 (01:35 +0200)]
ppc4xx: Fix sending type 1 PCI transactions
The list of 4xx SoCs that should send type 1 PCI transactions
is not defined correctly. As a result PCI-PCI bridges and devices
behind them are not identified. The following 4xx variants should
send type 1 transactions: 440GX, 440GP, 440SP, 440SPE, 460EX and 460GT.
Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Stefan Roese <sr@denx.de>
Mike Frysinger [Thu, 21 Jan 2010 09:03:22 +0000 (04:03 -0500)]
tools: allow people to compile w/out configuring
It's useful to be able to build up the host tools without having to select
a board first. Pretty much all tools in there are config-independent
anyways.
Also add a shortcut "tools-all" to quickly build all host tools that are
actually config-independent to allow for simple test builds.
Mike Frysinger [Thu, 21 Jan 2010 09:03:20 +0000 (04:03 -0500)]
image.h: avoid command.h for host tools
The u-boot command structures don't get used with host systems, so don't
bother including it when building host code. This avoids an implicit need
on config.h in the process.
Felix Radensky [Tue, 19 Jan 2010 19:19:06 +0000 (21:19 +0200)]
ppc4xx: Allow setting a single SPD EEPROM address for DDR2 DIMMs
On platforms where SPD EEPROM and another EEPROM have adjacent
I2C addresses SPD_EEPROM_ADDRESS should be defined as a single
element array, otherwise DDR2 setup code would fail with the
following error:
ERROR: Unknown DIMM detected in slot 1
However, fixing SPD_EEPROM_ADDRESS would result in another
error:
ERROR: DIMM's DDR1 and DDR2 type can not be mixed.
This happens because initdram() routine does not explicitly
initialize dimm_populated array. This patch fixes the problem.
Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Stefan Roese <sr@denx.de>
MIPS: qemu_mips: Import asm/unaligned.h from the Linux kernel
with a few adjustments for U-Boot. This fixes the following build error:
make -C lib_generic/
zlib.c:31:27: error: asm/unaligned.h: No such file or directory
zlib.c: In function 'inflate_fast':
zlib.c:641: warning: implicit declaration of function 'get_unaligned'
make[1]: *** [zlib.o] Error 1
make[1]: Leaving directory `/home/skuribay/git/u-boot.git/lib_generic'
make: *** [lib_generic/libgeneric.a] Error 2
Ben Warren [Mon, 18 Jan 2010 19:35:31 +0000 (11:35 -0800)]
Fix breakage in SMC EEPROM standalone applications
Commit 6a45e384955262882375a2785426dc65aeb636c4 (Make getenv_IPaddr() global)
inadvertently added ' #include "net.h" ' to the standalone programs, creating
duplicate definitions of 'struct eth_device'. This patch removes the local
definitions and removes other code that breaks due to the change in definition.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Daniel Hobi [Mon, 18 Jan 2010 17:13:39 +0000 (18:13 +0100)]
Makefile: fix parallel build
During parallel build, the top Makefile spawns multiple sub-makes for
targets in cpu/$(CPU) and $(dir $(LDSCRIPT)). If the .depend files are
not present in these directories, the sub-makes may end up generating
these files simultaneously which leads to corrupted content.
A typical error message is:
.depend:39: *** multiple target patterns. Stop.
This patch serializes the creation of .depend in cpu/$(CPU) and
$(dir $(LDSCRIPT)) by adding these directories to the depend target
in the top Makefile.
Other directories in $(LIBS) are not affected since they contain only
one Make target and thus only one sub-make is spawned per directory.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Heiko Schocher [Thu, 7 Jan 2010 07:55:54 +0000 (08:55 +0100)]
CRAMFS: support cramfs in RAM
cramfsls and cramfsload are added to the command list.
A cramfs placed at 'cramfs_addr' can the be listed with 'cramfsls' and files
can be loaded with 'cramfsload'. 'cramfs_addr' is an environment variable
specifying the address the cramfs is located.
This works for powerpc and for ARM.
Use CONFIG_CMD_CRAMFS.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de>
move definition of macros likely and unlikely to compiler.h
the macros likely and unlikely were defined in include/linux/mtd/compat.h,
but used in code not related to MTD. moved the macro definitions to compiler.h
Detlev Zundel [Tue, 22 Dec 2009 11:43:02 +0000 (12:43 +0100)]
cmd_bootm.c: Change interpretation of standalone image parameters.
Current code uses the second argument to bootm for standalone images to
override the load address specified in the image instead of passing all
parameters as is to the application. This behaviour is not documented
and not in line with how the go command works for standalone applications,
so we simply drop it.
Robin Getz [Mon, 21 Dec 2009 23:40:44 +0000 (18:40 -0500)]
kgdb: update mem2hex/hex2mem funcs
Convert the funcs to do the conversion inline so that we can do the copy
all at once with memcpy. This let's us push out an weird arch-specific
issue with accessing different regions of memory to the memcpy function
like the MMRs on Blackfin systems, and it should be a bit faster.
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Robin Getz [Mon, 21 Dec 2009 23:40:42 +0000 (18:40 -0500)]
kgdb: add default generic stubs
The default kgdb functions can be implemented with common U-Boot functions,
so rather than force everyone to copy & paste these things, create a set of
weak stubs.
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 3 Dec 2009 02:15:03 +0000 (21:15 -0500)]
config_defaults.h: new header for common u-boot config defaults
There are a bunch of features in U-Boot that we want to enable by default,
and it's best if we centralize them in one place rather than updating all
the board files out there.
Dirk Behme [Sun, 3 Jan 2010 07:33:58 +0000 (08:33 +0100)]
Make getenv_IPaddr() global
There are boards out there that do not have network support in
U-Boot (CONFIG_CMD_NET not set), but they do so in Linux. This
makes it desirable to be able to port network configuration (like
the IP address) to the Linux kernel.
We should not make the passing of the IP configuration to Linux
dependent on U-Boot features / settings.
For this, make getenv_IPaddr() global. This fixes build error
u-boot/lib_xxx/board.c:360: undefined reference to `getenv_IPaddr'
on various architectures.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Acked-by: Ben Warren <biggerbadderben@gmail.com>
Robin Getz [Mon, 21 Dec 2009 21:59:21 +0000 (16:59 -0500)]
Blackfin: keep hwtrace on CPLB miss
Crashes rarely happen in the CPLB miss handler compared to the rest of
U-Boot code, so disable hardware tracing when processing misses. This
way a crash due to other functions will be shown properly.
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
projects / u-boot / log