Tony Li [Fri, 17 Aug 2007 02:35:59 +0000 (10:35 +0800)]
mpc83xx: Split PIB init code from pci.c and add Qoc3 ATM card support
The patch split the PIB init code from pci.c to a single file board/freescale/common/pq-mds-pib.c
And add Qoc3 ATM card support for MPC8360EMDS and MPC832XEMDS board.
Kim Phillips [Thu, 16 Aug 2007 03:30:19 +0000 (22:30 -0500)]
mpc83xx: remaining 8360 libfdt fixes
PCI clocks and QE frequencies weren't being updated, and the core clock
was being updated incorrectly. This patch also adds a /memory node if
it doesn't already exist prior to update.
plus some cosmetic trimming to single line comments.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Jerry Van Baren [Wed, 15 Aug 2007 15:13:15 +0000 (11:13 -0400)]
Fix where the #ifdef CFG_BOOTMAPSZ is placed.
Commit 073e1b509980cefe6f53c2d7fbbcd135df1e3924 "Fix initrd/dtb
interaction" put the new code outside of the #if defined(CONFIG_OF_LIBFDT)
when it should have gone inside of the conditional. As a result, it
broke non-LIBFDT board builds.
Also added a missing "not." to the comment.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Ed Swarthout [Tue, 14 Aug 2007 19:06:45 +0000 (14:06 -0500)]
Fix malloc size error in ahci_init_one.
Typically this causes scsi init to corrupt the
devlist and break the coninfo command.
Fix a compiler size warning.
Signed-off-by: Jason Jin <jason.jin@freescale.com> Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Tue, 14 Aug 2007 15:32:59 +0000 (10:32 -0500)]
Fix initrd/dtb interaction
The original code would wrongly relocate the blob to be right before
the initrd if it existed. The blob *must* be within CFG_BOOTMAPSZ,
if it is defined. So we make two changes:
1) flag the blob for relocation whenever its address is above BOOTMAPSZ
2) If the blob is being relocated, relocate it before kbd, not initrd
Signed-off-by: Andy Fleming <afleming@freescale.com>
Stefan Roese [Tue, 14 Aug 2007 12:41:55 +0000 (14:41 +0200)]
POST: Add option for external ethernet loopback test
When CFG_POST_ETHER_EXT_LOOPBACK is defined, the ethernet POST
is not done using an internal loopback connection, but by assuming
that an external loopback connector is plugged into the board.
Peter Pearse [Tue, 14 Aug 2007 09:10:52 +0000 (10:10 +0100)]
Add MACH_TYPE records for several AT91 boards.
Merge to two at45.c files into a common file, split to at45.c and spi.c
Fix spelling error in DM9161 PHY Support.
Initialize at91rm9200 board (and set LED).
Add PIO control for at91rm9200dk LEDs and Mux.
Change dataflash partition boundaries to be compatible with Linux 2.6.
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Randy Vinson [Wed, 28 Feb 2007 02:42:22 +0000 (19:42 -0700)]
85xxCDS: Add make targets for legacy systems.
The PCI ID select values on the Arcadia main board differ depending
on the version of the hardware. The standard configuration supports
Rev 3.1. The legacy target supports Rev 2.x.
Haiying Wang [Tue, 19 Jun 2007 18:18:32 +0000 (14:18 -0400)]
Empirically set cpo and clk_adjust for mpc85xx DDR2 support
This patch is against u-boot-mpc85xx.git of www.denx.com
Setting cpo to 0x9 for frequencies higher than 333MHz is verified on
both MPC8548CDS board and MPC8568MDS board, especially for supporting
533MHz DDR2.
Setting clk_adjust to 0x6(3/4 late cycle) for MPC8568MDS board is for
DDR2 on all current board versions especially ver 1.92 or later to bring
up.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Andy Fleming [Mon, 13 Aug 2007 19:49:59 +0000 (14:49 -0500)]
MPC85xx BA bits not set for 3-bit bank address DIMM
The current implementation does not set the number of bank address bits
(BA) in the processor. The default assumes 2 logical bank bits. This
works fine for a DIMM that uses devices with 4 internal banks (SPD
byte17 = 0x4) but needs to be set appropriately for a DIMM that uses
devices with 8 internal banks (SPD byte17 = 0x8).
Signed-off-by: Greg Davis <DavisG@embeddedplanet.com>
Andy Fleming [Mon, 13 Aug 2007 19:38:06 +0000 (14:38 -0500)]
Fix minor 85xx warnings
Some patches had inserted warnings into the build:
* mpc8560ads declared data without using it
* cpu_init declared ecm and immap without using it in all CONFIGs
* MPC8548CDS.h had its default filenames changed so that they contained
"\m" in the paths. Made the defaults not Windows-specific (or
anything-specific)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Ed Swarthout [Fri, 27 Jul 2007 06:50:51 +0000 (01:50 -0500)]
8544ds PCIE support
PCI1 LAW mapping should use CFG_PCI1_MEM_PHY and not _BASE address.
Enable LBC and ECM errors and clear error registers.
Add tftpflash env var to get uboot from tftp server and flash it.
Add pci/pcie convenience env vars to display register space:
"run pcie3regs" to see all pcie3 ccsr registers
"run pcie3cfg" to see all cfg registers
Whitespace cleanup and MPC8544DS.h
Enable CONFIG_INTERRUPTS.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Tue, 14 Aug 2007 06:34:21 +0000 (01:34 -0500)]
85xx start.S cleanup and exception support
From: Ed Swarthout <Ed.Swarthout@freescale.com>
Support external interrupts from platform to eliminate system hangs.
Define CONFIG_INTERRUPTS board configure option to enable.
Enable ecm, ddr, lbc, and pci/pcie error interrupts in PIC.
Remove extra cpu initialization redundant with hardware initialization.
Whitespace cleanup.
Define and use _START_OFFSET consistent with other processors using
ppc_asm.tmpl
Move additional code from .text to boot page to make room for
exception vectors at start of image.
Handle Machine Check, External and Critical exceptions.
Fix e500 machine check error determination in traps.c
TEXT_BASE can now be 0xfffc_0000 - which cuts binary image in half.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
Calculate the data timeout based on values from the CSD instead of
just using a hardcoded DTOR value. This is a backport of a similar fix
in BSP 2.0, with one additional fix: the DTOCYC value is rounded up
instead of down.
include/asm-avr32/div64.h was recently moved to include/div64.h, but
cpu/at32ap/interrupts.c wasn't properly updated (an earlier version of
the patch was merged perhaps?)
This patch updates cpu/at32ap/interrupts.c so that the avr32 port
compiles again.
Instead of always using the largest blocksize the card supports, check
if it can support smaller block sizes and use 512 bytes if possible.
Most cards do support this, and other parts of u-boot seem to have
trouble with block sizes different from 512 bytes.
Wolfgang Denk [Sun, 12 Aug 2007 13:11:38 +0000 (15:11 +0200)]
Adapt board configuration and fix kernel crash on MCC200 board.
The update procedure was modified to turn off the USB subsystem
before exit for MCC200 and TRAB. This is necessary as otherwise the
USB controller continues to write periodically to system memory!
MCC200-specific notes:
- the patch disables the magic key check for MCC200
- the patch contains the configuration changes made
for the new revision of the board.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
Kim Phillips [Tue, 17 Jul 2007 18:56:53 +0000 (13:56 -0500)]
fdt: do board setup based on fdt address specified on bootm line
The last fdt patch to bootm did board setup based on the address
specified by a prior fdt address command invocation. The bootm
code, as its call to fdt_chosen does, should use the fdt specified
by the user on the bootm command. Note this restores full
functionality for the 8360's existing default boot environment
values, e.g. 'run nfsboot' (i.e. no having to 'fdt addr $fdtaddr'
before booting a kernel).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In the patch titled "Create new fdt boardsetup command..." I removed the
call to ft_board_setup() from the routine fdt_chosen(), but I forgot
to add a direct call back into cmd_bootm.c
This fixes the oversight by adding the direct call to the bootm command.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Gerald Van Baren [Tue, 26 Jun 2007 03:25:28 +0000 (23:25 -0400)]
Create new fdt boardsetup command, fix bug parsing [] form of set values.
Previously ft_board_setup() was called by fdt_chosen() which was not
really correctly structured. This splits ft_board_setup() out by creating
a new fdt boardsetup command.
Fix a bug when parsing fdt set command values which have the square
bracket form [00 11 22 33] - the length was updated incorrectly in when
parsing that form.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Gerald Van Baren [Thu, 17 May 2007 02:39:59 +0000 (22:39 -0400)]
Fix cmd_fdt line lengths, refactor code.
Break lines that were greater than 80 characters in length.
Move the fdt print and property parsing code to separate static functions
to reduce coding clutter in the fdt_cmd handling body.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Gerald Van Baren [Sat, 12 May 2007 13:45:46 +0000 (09:45 -0400)]
Reorganize and fix problems (returns) in the bootm command.
Do *NOT* return after the "point of no return" has been passed.
If something goes wrong, the board must be reset after that point.
Move the "Transferring control to Linux" debug message back to where it
belongs: just before transferring control to linux.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Print more than the raw libfdt error message strings. This is especially
useful for cluing in the user when the bootm command aborts due to
blob problems.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
projects / u-boot / log