Trent Piepho [Wed, 3 Dec 2008 23:16:37 +0000 (15:16 -0800)]
mpc8[56]xx: Put localbus clock in sysinfo and gd
Currently MPC85xx and MPC86xx boards just calculate the localbus frequency
and print it out, but don't save it.
This changes where its calculated and stored to be more consistent with the
CPU, CCB, TB, and DDR frequencies and the MPC83xx localbus clock.
The localbus frequency is added to sysinfo and calculated when sysinfo is
set up, in cpu/mpc8[56]xx/speed.c, the same as the other frequencies are.
get_clocks() copies the frequency into the global data, as the other
frequencies are, into a new field that is only enabled for MPC85xx and
MPC86xx.
checkcpu() in cpu/mpc8[56]xx/cpu.c will print out the local bus frequency
from sysinfo, like the other frequencies, instead of calculating it on the
spot.
Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
Trent Piepho [Wed, 3 Dec 2008 23:16:35 +0000 (15:16 -0800)]
mpc8568: Double local bus clock divider
The clock divider for the MPC8568 local bus should be doubled, like the
other newer MPC85xx chips.
Since there are now more chips with a 2x divider than a 1x, and any new
85xx chips will probably be 2x, invert the sense of the #if so that it
lists the 1x chips instead of the 2x ones.
Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
Dave Liu [Tue, 16 Dec 2008 04:09:27 +0000 (12:09 +0800)]
85xx: Fix the boot window issue
If one custom board is using the 8MB flash, it is set
as FLASH_BASE = 0xef000000, TEXT_BASE = 0xef780000.
The current start.S code will be broken at switch_as.
It is because the TLB1[15] is set as 16MB page size,
EPN = TEXT_BASE & 0xff000000, RPN = 0xff000000.
For the 8MB flash case, the EPN = 0xefxxxxxx,
RPN = 0xffxxxxxx. Assume the virt address of switch_as
is 0xef7ff18c, the real address of the instruction at
switch_as should be 0xff7ff18c. the 0xff7ff18c is out
of the range of the default 8MB boot LAW window
0xff800000 - 0xffffffff.
So when we switch to AS1 address space at switch_as,
the core can't fetch the instruction at switch_as any
more. It will cause broken issue.
Paul Gortmaker [Thu, 11 Dec 2008 20:47:50 +0000 (15:47 -0500)]
sbc8548: use proper PHY address
The values given for the PHY address were wrong, so the code
read no valid PHY ID, and fell through to the generic PHY
support, which would work on 1000M but would not auto negotiate
down to 100M or 10M.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Haiying Wang [Wed, 3 Dec 2008 15:08:19 +0000 (10:08 -0500)]
Set IVPR to kenrel entry point in second core boot page
Assuming the OSes exception vectors start from the base of kernel address, and
the kernel physical starting address can be relocated to an non-zero address.
This patch enables the second core to have a valid IVPR for debugger before
kernel setting IVPR in CAMP mode. Otherwise, IVPR is 0x0 and it is not a valid
value for second core which runs kernel at different physical address other
than 0x0.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Trent Piepho [Wed, 3 Dec 2008 23:16:38 +0000 (15:16 -0800)]
mpc8[56]xx: Put localbus clock in device tree
Export the localbus frequency in the device tree, the same way the CPU, TB,
CCB, and various other frequencies are exported in their respective device
tree nodes.
Some localbus devices need this information to be programed correctly, so
it makes sense to export it along with the other frequencies.
Unfortunately, when someone wrote the localbus dts bindings, they didn't
bother to define what the "compatible" property should be. So it seems no
one was quite sure what to put in their dts files.
Based on current existing dts files in the kernel source, I've used
"fsl,pq3-localbus" and "fsl,elbc" for MPC85xx, which are used by almost all
of the 85xx devices, and are looked for by the Linux code. The eLBC is
apparently not entirely backward compatible with the pq3 LBC and so eLBC
equipped platforms like 8572 won't use pq3-localbus.
For MPC86xx, I've used "fsl,elbc" which is used by some of the 86xx systems
and is also looked for by the Linux code. On MPC8641, I've also used
"fsl,mpc8641-localbus" as it is also commonly used in dts files, some of
which don't use "fsl,elbc" or any other acceptable name to match on.
Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
Kumar Gala [Tue, 16 Dec 2008 20:59:22 +0000 (14:59 -0600)]
NAND FSL elbc: Use virt_to_phys to determine which bank is in use
The current code that determines which bank/chipselect is used for a
given NAND instance only worked for 32-bit addresses and assumed
a 1:1 mapping. This breaks in 36-bit physical configs.
The proper way to handle this is to use the virt_to_phys() and
BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address
with the the virtual address the NAND code uses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Scott Wood <scottwood@freescale.com>
Peter Tyser [Wed, 17 Dec 2008 22:36:21 +0000 (16:36 -0600)]
Add support for PCA953x I2C gpio devices
Initial support for NXP's 4 and 8 bit I2C gpio expanders
(eg pca9537, pca9557, etc). The CONFIG_PCA953X define
enables support for the devices while the CONFIG_CMD_PCA953X
define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO
define enables an 'info' sub-command which provides summary
information for the given pca953x device.
Wolfgang Denk [Tue, 16 Dec 2008 21:32:25 +0000 (22:32 +0100)]
board/trab/memory.c: Fix compile problems.
Apply changes from commit 44b4dbed to board/trab/memory.c, too.
Actually we'd need a major cleanup here - as it turns out,
board/trab/memory.c is more or less a verbatim copy of
post/drivers/memory.c ... but then, trab is EOL anyway,r
so this is not worth the effort.
Scott Wood [Tue, 16 Dec 2008 20:24:16 +0000 (14:24 -0600)]
NAND: Mark the BBT as scanned prior to calling scan_bbt.
Otherwise, recursion can occur if scan_bbt does not find a bad block
table, and tries to write one, and the attempt to erase the BBT area
causes a bad block check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Becky Bruce [Thu, 4 Dec 2008 05:04:37 +0000 (23:04 -0600)]
powerpc: fix io.h build warning with CONFIG_PHYS_64BIT
Casting a pointer to a phys_addr_t when it's an unsigned long long
on a 32-bit system without first casting to a non-pointer type
generates a compiler warning. Fix this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Wolfgang Denk [Tue, 16 Dec 2008 13:44:06 +0000 (14:44 +0100)]
post/Makefile: fix dependency problem with parallel builds
Parallel builds (using "make -jN") would occasionally fail with error
messages like
ppc_4xxFP-objdump: string.o: File format not recognized
or
post/libpost.a(cpu.o): In function `cpu_post_test':
/home/wd/git/u-boot/work/post/lib_ppc/cpu.c:130: undefined reference to `cpu_post_test_string'
or similar. We now make sure to run the 'postdeps" step before
attempting to build the specific POST libraries.
Wolfgang Denk [Tue, 16 Dec 2008 13:41:02 +0000 (14:41 +0100)]
Makefile: fix dependency problem with parallel builds
Parallel builds (using "make -jN") would occasionally fail with error
messages like
include/autoconf.mk:212: *** missing separator. Stop.
Line numbers and affected boards were changing. Obviously some
Makefiles included autoconf.mk while it was still being written to.
As a fix, we now write to a temporary file first and then rename it,
so that it is really ready to use as soon as it appears.
Mike Frysinger [Thu, 11 Dec 2008 23:39:08 +0000 (18:39 -0500)]
spi/stmicro: fix debug() display of cmd
The stmicro_wait_ready() func tries to show the actual opcode that was sent
to the device, but instead it displays the array pointer. Fix it to pull
out the opcode from the start of the array.
Mike Frysinger [Thu, 11 Dec 2008 11:23:37 +0000 (06:23 -0500)]
env_sf: support embedded environments
If both CONFIG_ENV_SECT_SIZE and CONFIG_ENV_SIZE are defined, and the sect
size is larger than the env size, then it means the env is embedded in a
block. So we have to save/restore the part of the sector which is not the
environment. Previously, saving the environment in SPI flash in this
setup would probably brick the board as the rest of the sector tends to
contain actual U-Boot data/code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Timur Tabi [Wed, 3 Dec 2008 17:28:30 +0000 (11:28 -0600)]
i2c: merge all i2c_reg_read() and i2c_reg_write() into inline functions
All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.
Signed-off-by: Timur Tabi <timur@freescale.com> Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Kumar Gala [Sat, 13 Dec 2008 23:20:28 +0000 (17:20 -0600)]
Introduce addr_map library
Add a library that helps in translating between virtual and physical
addresses. This library can be useful as a simple means to implement
map_physmem() and virt_to_phys() for platforms that need functionality
beyond the simple 1:1 mapping.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sat, 13 Dec 2008 23:20:27 +0000 (17:20 -0600)]
Introduce virt_to_phys()
virt_to_phys() returns the physical address given a virtual. In most
cases this will be just the input value as the vast majority of
systems run in a 1:1 mode.
However in systems that are not running this way it should report the
physical address or ~0 if no mapping exists for the given virtual
address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Stefan Roese [Tue, 18 Nov 2008 15:36:12 +0000 (16:36 +0100)]
MIPS: Flush data cache upon relocation
This patch now adds a flush to the data cache upon relocation. The
current implementation is missing this. Only a comment states that it
should be done. So let's really do it now.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Tue, 18 Nov 2008 15:36:22 +0000 (16:36 +0100)]
MIPS: Add CONFIG_SKIP_LOWLEVEL_INIT
This patch adds the CONFIG_SKIP_LOWLEVEL_INIT option to start.S. This
enables support for boards where the lowlevel initialization is
already done when U-Boot runs (e.g. via OnChip ROM).
This will be used in the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Wed, 12 Nov 2008 12:18:02 +0000 (13:18 +0100)]
MIPS: Add board_early_init_f() to init_sequence
This patch adds the board_early_init_f() call to the MIPS init
sequence. A weak dummy implementation is also added which can be
overridden by a board specific version.
This will be used by the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Wed, 12 Nov 2008 12:18:19 +0000 (13:18 +0100)]
MIPS: Add onenand_init() to board.c and move nand_init()
This patch adds a call to onenand_init() for OneNAND support and moves
the nand_init() call to an earlier place, so that the environment can
be used from NAND and OneNAND.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Wed, 10 Dec 2008 09:32:59 +0000 (10:32 +0100)]
UBI: Set ubi_dev.type back to DEV_TYPE_NONE upon failing initialization
With this patch we set the type back to NONE upon failing UBI partition
initialization. Otherwise further calls to the UBI subsystem would try
to really access the non-existing UBI partition.
Michal Simek [Tue, 25 Nov 2008 10:42:20 +0000 (11:42 +0100)]
microblaze: Remove XUPV2P board
---
Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.
This change will go through microblaze custodian tree.
Mike Frysinger [Wed, 10 Dec 2008 04:20:31 +0000 (23:20 -0500)]
tools/netconsole: new script for working with netconsole over UDP
While the doc/README.NetConsole does have a snippet for people to
create their own netcat script, it's a lot easier to make a simple
dedicated script and tell people to use it.
Ilya Yanok [Thu, 13 Nov 2008 16:49:36 +0000 (19:49 +0300)]
jffs2: cache data_crc results
As we moved data_crc() invocation from jffs2_1pass_build_lists() to
jffs2_1pass_read_inode() data_crc is going to be calculated on each
inode access. This patch adds caching of data_crc() results. There
is no significant improvement in speed (because of flash access
caching added in previous patch I think, crc in RAM is really fast)
but this patch impacts memory usage -- every b_node structure uses
12 bytes instead of 8.
Ilya Yanok [Thu, 13 Nov 2008 16:49:34 +0000 (19:49 +0300)]
jffs2: add buffer to cache flash accesses
With this patch JFFS2 code allocates memory buffer of max_totlen size
(size of the largest node, calculated during scan time) and uses it to
store entire node. Speeds up loading. If malloc fails we use old ways
to do things.
Ilya Yanok [Thu, 13 Nov 2008 16:49:33 +0000 (19:49 +0300)]
jffs2: rewrite jffs2 scanning code based on Linux one
Rewrites jffs2_1pass_build_lists() function in style of Linux's
jffs2_scan_medium() and jffs2_scan_eraseblock().
This includes:
- Caching flash acceses
- Smart dealing with free space
Ilya Yanok [Thu, 13 Nov 2008 16:49:31 +0000 (19:49 +0300)]
jffs2: fix searching for latest version in jffs2_1pass_list_inodes()
We need to update i_version inside cycle to find really latest version
inside jffs2_1pass_list_inodes(). With that fixed we can use isize inside
dump_inode() instead of calling expensive jffs2_1pass_read_inode().
projects / u-boot / log