Akshay Bhat [Fri, 29 Jan 2016 20:16:40 +0000 (15:16 -0500)]
arm: imx: Add support for GE Bx50v3 boards
Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Stephen Warren [Sat, 5 Mar 2016 17:30:53 +0000 (10:30 -0700)]
malloc: remove !gd handling
Following the previous patch, malloc() is never called before gd is set,
so we can remove the special-case check for this condition.
This reverts commit 854d2b9753e4 "dlmalloc: ensure gd is set for early
alloc".
Cc: Rabin Vincent <rabin@rab.in> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Sat, 5 Mar 2016 17:30:52 +0000 (10:30 -0700)]
malloc: use hidden visibility
When running sandbox, the following phases occur, each with different
malloc implementations or behaviors:
1) Dynamic linker execution, using the dynamic linker's own malloc()
implementation. This is fully functional.
2) After U-Boot's malloc symbol has been hooked into the GOT, but before
any U-Boot code has run. This phase is entirely non-functional, since
U-Boot's gd symbol is NULL and U-Boot's initf_malloc() and
mem_malloc_init() have not been called.
At least on Ubuntu Xenial, the dynamic linker does make both malloc() and
free() calls during this phase. Currently these free() calls crash since
they dereference gd, which is NULL.
U-Boot itself makes no use of malloc() during this phase.
3) U-Boot execution after gd is set and initf_malloc() has been called.
This is fully functional, albeit via a very simple malloc()
implementation.
4) U-Boot execution after mem_malloc_init() has been called. This is fully
functional with a complete malloc() implementation.
Furthermore, if code that called malloc() during phase 1 calls free() in
phase 3 or later, it is likely that heap corruption will occur, since
U-Boot's malloc implementation will assume the pointer is part of its own
heap, although it isn't. I have not actively observed this happening.
To prevent phase 2 from happening, this patch makes all of U-Boot's malloc
library public symbols have hidden visibility. This prevents them from
being hooked into the GOT, so only code in the U-Boot binary itself
actually calls them; any other code will call into the standard C library
malloc(). This also avoids the "furthermore" issue mentioned above.
I have seen references to this GCC pragma in blog posts from 2008, and
RHEL5's ancient gcc appears to accept it fine, so I believe it's quite
safe to use it without checking gcc version.
Cc: Rabin Vincent <rabin@rab.in> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 5 Mar 2016 19:07:44 +0000 (14:07 -0500)]
sandbox: Fix building with LLVM
- The macro __BIGGEST_ALIGNMENT__ is gcc-specific. If it is not defined
we'll just assume 16. This is correct for at least the common cases
and LLVM does not provide an equivalent macro.
- When linking U-Boot we're passing -T to the linker, and while gcc will
just pass this along with LLVM we need to be specific.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
api: Export API structure address as an environment variable
This patch makes the U-Boot api export its structure address as an environment
variable, so it can be used to directly hint FreeBSD's loader of api's location.
The relevant FreeBSD loader change is currently under review at:
https://reviews.freebsd.org/D5492
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Masahiro Yamada [Fri, 4 Mar 2016 06:56:16 +0000 (15:56 +0900)]
pinctrl: uniphier: set input-enable before pin-muxing
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary overcurrent
error which would then disable the host port.
The overcurrent condition was happening on the SoCFPGA Cyclone5 devkit, thus
USB was not working on the devkit. This patch fixes that problem.
Soeren Moch [Tue, 9 Feb 2016 15:53:27 +0000 (16:53 +0100)]
board: tbs2910: Fix eMMC BOOTCFG value
Fix the BOOTCFG value for eMMC in the same way as commit 214c3f0f9921250eb336c7effadcc16158ea9df5
[imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failure]
did for sabresd.
Bhuvanchandra DV [Wed, 24 Feb 2016 08:33:24 +0000 (14:03 +0530)]
colibri-vf: Disable pull-up configuration in GPIO pin mux
During very early boot-ROM execution the pinmux
configuration isi in Hi-Z state. If pull-up is enabled
on GPIO pad's there will be a short period of toggle
from high to low on the IO when GPIO is set low during
boot. To avoid this glitch, disable pull-up configuration
in GPIO pinmux.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Sam Protsenko [Tue, 16 Feb 2016 17:59:19 +0000 (19:59 +0200)]
usb: gadget: composite: Correct recovery path for register
In case when usb_composite_register() failed once (for whatever reason),
it will fail further even if all conditions are correct. Example:
=> fastboot 2
Invalid Controller Index
couldn't find an available UDC
g_dnl_register: failed!, error: -19
exit not allowed from main input shell.
=> fastboot 0
g_dnl_register: failed!, error: -22
exit not allowed from main input shell.
Despite that 0 is correct index for USB controller, "fastboot 0" command
will fail, because "composite" structure wasn't cleared properly on
previous fail (on "fastboot 2" command).
This patch fixes that erroneous behavior, allowing us to use composite
even after previous failure.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Sam Protsenko [Fri, 26 Feb 2016 19:37:52 +0000 (21:37 +0200)]
arm: dra7xx: Define Android partition table
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
sniper: Various minor cleanups, missing Kconfig configs and reorganisation
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 29 Feb 2016 19:47:47 +0000 (14:47 -0500)]
amcc-common.h: Disable CONFIG_SYS_LONGHELP
There are a number of AMCC platforms which are close to, or with some
toolchains exceeding, the size constraints. Disable CONFIG_SYS_LONGHELP
to get us room to build with again.
Tom Rini [Mon, 29 Feb 2016 16:34:15 +0000 (11:34 -0500)]
compiler*.h: sync include/linux/compiler*.h with Linux 4.5-rc6
Copy these from Linux v4.5-rc6 tag.
This is needed so that we can keep up with newer gcc versions. Note
that we don't have the uapi/ hierarchy from the kernel so continue to
use <linux/types.h>
Masahiro Yamada [Fri, 26 Feb 2016 09:59:45 +0000 (18:59 +0900)]
ARM: uniphier: fix warnings reported by aarch64 compiler
The UniPhier SoC family has not supported ARMv8 yet, but these would
cause warnings if they were compiled with a 64bit compiler. Before
adding the ARMv8 support really, fix them now.
Because UniPhier SoCs do not support Large Physical Address Extension,
casting "phys_addr_t" into "unsigned long" would carry the address
as is.
Masahiro Yamada [Fri, 26 Feb 2016 09:59:44 +0000 (18:59 +0900)]
ARM: uniphier: prepare directory structure for ARMv8 SoC support
Before adding ARMv8 support, this commit refactors the directory
structure. Move ARMv7 specific files to arch/arm/mach-uniphier/arm32
to avoid a mess by mixture of ARMv7 and ARMv8 code. Also move the
"select CPU_V7" to the lower-level menu because we will have to
select ARM64 instead of CPU_V7 for ARMv8 SoCs.
While this is a correct change to do long term it unfortunately breaks a
number of platforms that are using pdata and not named struct members so
they are getting all of their data after 'base' incorrect.
Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Fri, 26 Feb 2016 09:59:42 +0000 (18:59 +0900)]
ARM: uniphier: rework UniPhier SoC select in Kconfig
The chains of "depends on <SoC_name>" in the current Kconfig is
clumsy. The idea here is to allow users to choose a SoC group first
(SoC group consists of some SoCs that can coexist in one binary).
Then, allow to enable/disable each SoC support in the selected SoC
group. This makes the Kconfig menu clearer.
Masahiro Yamada [Fri, 26 Feb 2016 09:59:41 +0000 (18:59 +0900)]
ARM: uniphier: merge two defconfig files
PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one
image and there is bit more room in SPL to accommodate all of them.
Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig.
Masahiro Yamada [Fri, 26 Feb 2016 05:21:41 +0000 (14:21 +0900)]
ARM: uniphier: merge DDR PHY init code for 3 SoCs
Now these three are almost the same. The only difference is the DTPR1
register dependency on the DRAM size, but it can be ignored. (It has
already been ignored in PH1-sLD8 and PH1-Pro4.)
Masahiro Yamada [Fri, 26 Feb 2016 05:21:40 +0000 (14:21 +0900)]
ARM: uniphier: add a field to specify DDR3+
Add a field to distinguish DDR3+ from (standard) DDR3. It also
allows to delete CONFIG_DDR_STANDARD (this is not a software
configuration, but a board attribute).
Masahiro Yamada [Fri, 26 Feb 2016 05:21:38 +0000 (14:21 +0900)]
ARM: uniphier: remove UMC_INITCTL* and UMC_DRMR* settings
These settings were used only for the PH1-sLD3 and older SoCs. The
PH1-LD4 and newer one just ignore them because their DDR-PHY take
care of such timing parameters instead.
Masahiro Yamada [Fri, 26 Feb 2016 05:21:37 +0000 (14:21 +0900)]
ARM: uniphier: refactor UMC init code for ProXstream2
Currently, a dummy value is defined for the UMC_SPCCTLA register
when the DRAM size is zero. This seems weird because the controller
does not need setting in the first place if the size is zero.
Also, redefine enum dram_size to represent the DRAM size per 16-bit
unit. This makes things simpler because the channel 0 and 1 are
connected with 32-bit width DRAM, while the channel 2 is connected
with 16-bit width one.
I am renaming SIZE_* into DRAM_SZ_* (and also FREQ_* to DRAM_FREQ_*
for consistency) while I am here because SIZE_* might be easily
mixed-up with the macros in include/linux/sizes.h.
Masahiro Yamada [Fri, 26 Feb 2016 05:21:34 +0000 (14:21 +0900)]
ARM: uniphier: rework struct uniphier_board_data
This commit reworks "struct uniphier_board_data" with an array of
DRAM channel data in it. It will allow further cleanups by means of
"for" statements that iterate over the DDR channels.
Masahiro Yamada [Tue, 16 Feb 2016 08:08:41 +0000 (17:08 +0900)]
ARM: uniphier: add emmcupdate command
The Boot ROM expects the boot image (SPL) in the Boot Partition 1.
So, updating images involves the hardware partition switch. It might
be a bit advanced for some users.
To be user-friendly, this commit adds a useful command to update the
images; just put SPL and U-Boot proper into the public directory of
the TFTP server and execute "run emmcupdate" from the command line.
Masahiro Yamada [Tue, 16 Feb 2016 08:08:39 +0000 (17:08 +0900)]
ARM: uniphier: add eMMC boot support
Export device nodes needed for eMMC boot (eMMC node, pinctrl, and
clock) to the SPL DTB. CONFIG_SUPPORT_EMMC_BOOT is also necessary
to use "mmc partconf" command.
Masahiro Yamada [Tue, 16 Feb 2016 08:03:49 +0000 (17:03 +0900)]
gpio: do not include <asm/arch/gpio.h> for UniPhier
I implemented a GPIO driver based on Driver Model for the UniPhier
SoC family, but I could not find any good reason why such SoC
specific GPIO headers are needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
net: bootp: Add environment variable for timeout period
There is currently one config option (CONFIG_NET_RETRY_COUNT) that
is available to tune the retries of the network stack.
Unfortunately, it is global to all protocols, and the value is
interpreted differently in all of them.
Add a new environment variable that directly sets the retry period for
BOOTP timeouts. If this new value is not set, the period is still derived
from the default number of retries, or from CONFIG_NET_RETRY_COUNT if
defined. When both the new variable is set and CONFIG_NET_RETRY_COUNT
is defined, the variable has precedence.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Alison Wang [Fri, 19 Feb 2016 07:52:28 +0000 (15:52 +0800)]
net: phy: atheros: Fix problem with phy_reset() clearing BMCR
In commit <a058052c358c> [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Bit 12(AUTO_NEGOTIATION)
is cleared too. It causes auto-negotiation timeout error on Atheros's
PHY AR8033.
To fix this problem, genphy_config_aneg() and genphy_restart_aneg()
needs to be called in ar8035_config() to enable and restart
auto-negotiation.
Signed-off-by: Alison Wang <alison.wang@nxp.com> Acked-by: Stefan Agner <stefan@agner.ch> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Fri, 26 Feb 2016 18:23:27 +0000 (19:23 +0100)]
usb: ehci: Fix warning on aarch64
Fix the following warning on aarch64 introduced by using p2v/v2p
functions in the code:
In file included from ./arch/arm/include/asm/byteorder.h:29:0,
from include/compiler.h:125,
from include/image.h:19,
from include/common.h:88,
from drivers/usb/host/ehci-hcd.c:10:
drivers/usb/host/ehci-hcd.c: In function ‘ehci_td_buffer’:
drivers/usb/host/ehci-hcd.c:250:49: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
^
include/linux/byteorder/little_endian.h:34:51: note: in definition of macro ‘__cpu_to_le32’
#define __cpu_to_le32(x) ((__force __le32)(__u32)(x))
^
drivers/usb/host/ehci-hcd.c:250:24: note: in expansion of macro ‘cpu_to_hc32’
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
Bin Meng [Thu, 18 Feb 2016 07:14:47 +0000 (23:14 -0800)]
pci: Fix compiler warnings in dm_pciauto_setup_device()
Fix the following compiler warnings when DEBUG is on.
warning: 'bar_res' may be used uninitialized in this function.
drivers/pci/pci_auto.c:101:21:
if (!enum_only && pciauto_region_allocate(bar_res, bar_size,
^
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 24 Feb 2016 16:14:56 +0000 (09:14 -0700)]
spi: Correct two error return values
When an error number is provided we should use it, not change it. This fixes
the SPI and SPI flash tests.
One of these is long-standing. The other seems to have been introduced by
commit 1e90d9fd (sf: Move read_id code to sf_ops).
Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: 1e90d9fd (sf: Move read_id code to sf_ops) Reviewed-by: Jagan Teki <jteki@openedev.com> Tested-by: Jagan Teki <jteki@openedev.com>
Simon Glass [Wed, 24 Feb 2016 16:14:55 +0000 (09:14 -0700)]
sandbox: spi: Remove an incorrect free()
We must not free data that is managed by driver mode. Remove this line,
which is a hangover from the pre-driver-model code.
This fixes a problem where 'sf probe' crashes U-Boot if the backing file
for the SPI flash cannot be found.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 24 Feb 2016 16:14:50 +0000 (09:14 -0700)]
timer: Set up the real timer after driver model is available
When using the early timer, we need to manually trigger setting up the
real timer. This will not happen automatically. Do this immediately after
starting driver model.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 24 Feb 2016 16:14:49 +0000 (09:14 -0700)]
timer: Provide an early timer
In some cases the timer must be accessible before driver model is active.
Examples include when using CONFIG_TRACE to trace U-Boot's execution before
driver model is set up. Enable this option to use an early timer. These
functions must be supported by your timer driver: timer_early_get_count()
and timer_early_get_rate().
Simon Glass [Wed, 24 Feb 2016 16:14:47 +0000 (09:14 -0700)]
trace: Improve the trace test number recognition
The awk tool can be confused by return character (ASCII 13) in its input
since it thinks there is a separate field. These can appear if the terminal
is in raw mode, perhaps due to a previous U-Boot crash with sandbox. This
is very confusing. Remove these so that the trace test passes.
On signature verification failures fit_image_verify() should NOT exit with
error. Only keys marked 'required' can cause image verification failure.
This logic is already there and works correctly.
Add a comment to make this clear.
Fixes: 84ca65aa (image-fit: Fix signature checking) Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 24 Feb 2016 16:14:42 +0000 (09:14 -0700)]
image: Correct the OS location code to work on sandbox
A recent change broke the 'bootm' command on sandbox. The root cause is
using a pointer as an address. Conversion from pointer to address needs to
use map_to_sysmem() so that sandbox can do the right thing. The problem was
pre-existing but uncovered by a recent commit.
Fix this. Also move fit_get_end() to the C file to avoid needing to include
mapmem.h (and thus asm/io.h) everywhere.
Fixes: 1fec3c5d (common/image.c: Make boot_get_ramdisk() perform a check for Android images) Signed-off-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Tue, 16 Feb 2016 00:40:34 +0000 (17:40 -0700)]
test/py: skip tests that require large CONFIG_SYS_MAXARGS
test_hush_if_test.py executes commands that require large values of
CONFIG_SYS_MAXARGS. Detect cases where the configured value is too low
and skip those tests.
Ideally, this would be implemented inside console.run_command(). However,
the command passed to that function is already a completely formed string,
and determining its argument count usage would require splitting commands
at ;, handling quoting to deal with arguments containing spaces, etc. Even
passing the command as a list wouldn't solve all these issues, since we'd
still need to split commands on ; and deal with cases like "if test ..."
which consumes 0 of the argument count.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Tue, 16 Feb 2016 00:39:38 +0000 (17:39 -0700)]
test/py: use space to interrupt autoboot
Sending CTRL-C to QEMU's stdin aborts the process, even if stdin is being
used as a serial port (at least in the raspi2 machine with "qemu -serial
stdin"). Avoid sending CTRL-C to U-Boot to prevent it exiting.
I'd originally used CTRL-C to make sure that if the character used to
abort autoboot ended up being treated as part of a command as well, it'd
abort command entry and return the prompt to a known state. However, this
is not needed, since aborting the autoboot eats the character used to do
that.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Simon Glass <sjg@chromium.org>
projects / u-boot / log