Paul Burton [Thu, 18 Jan 2018 22:36:41 +0000 (14:36 -0800)]
boston: Pad binary in .mcs to a multiple of 16 bytes
When flashing U-Boot on a Boston board using Xilinx Vivado tools, the
final 0x00 byte which ends the .relocs section seems to be skipped &
left in flash as 0xff unless the data contained in the .mcs is padded
out to a 16 byte boundary. Without our final zero byte relocation will
fail with an error about a spurious reloc:
Avoid this problem by padding out the data in the .mcs file to a 16 byte
boundary using srec_cat's -range-pad functionality.
Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Jaehoon Chung [Tue, 23 Jan 2018 05:04:30 +0000 (14:04 +0900)]
mmc: fix to assign to correct clock value when clock is enabling
When clock is enabling, it's assigned to 0 as mmc->clock.
Then it can't initialize any card.
Fix to assign to correct clock value as mmc->cfg->f_min or f_max.
Jaehoon Chung [Tue, 16 Jan 2018 06:33:50 +0000 (15:33 +0900)]
power: regulator: s2mps11: add a regulator driver for s2mps11
exynos5422 has the s2mps11 PMIC.
s2mps11 pmic has the 10-BUCK and 38-LDO regulators.
Each IP and devices in exynos5422 can be controlled by each regulators.
This patch is support for s2mps11 regulator driver.
Ashish Kumar [Wed, 17 Jan 2018 06:46:36 +0000 (12:16 +0530)]
fsl: common: qixis: Add ifc and emmc switching via qixis
Currently only SD, NAND can be secondary boot sources controlled
by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR
can be secondary boot source, while QSPI-NOR is the primary.
Add options in qixis to switch to other boot sources including
ifc and emmc.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Pankaj Bansal [Thu, 18 Jan 2018 04:13:33 +0000 (09:43 +0530)]
ARM: dts: Freescale: re-license device tree files under GPLv2+/X11
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, re-license the the device trees for
Freescale (now NXP) SoCs and boards under GPLv2+/X11 dual license.
Same trend is followed in linux.
Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Mingkai Hu <mingkai.hu@nxp.com> Cc: York Sun <york.sun@nxp.com> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Rajesh Bhagat [Wed, 17 Jan 2018 10:43:09 +0000 (16:13 +0530)]
ls1088a: Add VID support for QDS and RDB platforms
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Rajesh Bhagat [Wed, 17 Jan 2018 10:43:03 +0000 (16:13 +0530)]
board: common: vid: Move IR chip specific code in flag
Moves IR chip (IR36021) specific code in flag to resolve
compilation issue where it is not present. For example,
LS1088A is having a new LTC3882 voltage chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Adam Ford [Thu, 11 Jan 2018 14:20:27 +0000 (08:20 -0600)]
Convert CONFIG_SOC_DA8XX et al to Kconfig
This converts the following to Kconfig:
CONFIG_SOC_DA8XX
CONFIG_SOC_DA850
CONFIG_DA850_LOWLEVEL
CONFIG_MACH_DAVINCI_DA850_EVM
CONFIG_SYS_DA850_PLL_INIT
CONFIG_SYS_DA850_DDR_INIT
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: David Lechner <david@lechnology.com>
[trini: Rework CONFIG_SYS_DA850_PLL_INIT so it's selected on SOC_DA8XX] Signed-off-by: Tom Rini <trini@konsulko.com>
efi_loader: allow creation of more device part nodes
Create device path nodes for UCLASS_ETH udevices.
Create device path nodes of block device children of UCLASS_MMC udevices.
Consistently use debug for unsupported nodes.
Set the log level to error.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Fix build failure by adding #ifdef CONFIG_DM_ETH] Signed-off-by: Alexander Graf <agraf@suse.de>
This test checks the driver for block IO devices.
A disk image is created in memory.
A handle is created for the new block IO device.
The block I/O protocol is installed on the handle.
ConnectController is used to setup partitions and to install the simple
file protocol.
A known file is read from the file system and verified.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides
* a uclass for EFI drivers
* a EFI driver for block devices
For each EFI driver the uclass
* creates a handle
* adds the driver binding protocol
The uclass provides the bind, start, and stop entry points for the driver
binding protocol.
In bind() and stop() it checks if the controller implements the protocol
supported by the EFI driver. In the start() function it calls the bind()
function of the EFI driver. In the stop() function it destroys the child
controllers.
The EFI block driver binds to controllers implementing the block io
protocol.
When the bind function of the EFI block driver is called it creates a
new U-Boot block device. It installs child handles for all partitions and
installs the simple file protocol on these.
The read and write functions of the EFI block driver delegate calls to the
controller that it is bound to.
A usage example is as following:
U-Boot loads the iPXE snp.efi executable. iPXE connects an iSCSI drive and
exposes a handle with the block IO protocol. It calls ConnectController.
Now the EFI block driver installs the partitions with the simple file
protocol.
iPXE uses the simple file protocol to load Grub or the Linux Kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: add comment on calloc len] Signed-off-by: Alexander Graf <agraf@suse.de>
efi_loader: provide function to get last node of a device path
On a block device and its partitions the same protocols can be
installed. To tell the apart we can use the type of the last
node of the device path which is not the end node.
The patch provides a utility function to find this last node.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Add the revision constants.
Depending on the revision additional fields are needed in the
media descriptor.
Use efi_uintn_t for number of bytes to read or write.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
efi_loader: make efi_disk_create_partitions a global symbol
Up to now we have been using efi_disk_create_partitions() to create
partitions for block devices that existed before starting an EFI
application.
We need to call it for block devices created by EFI
applications at run time. The EFI application will define the
handle for the block device and install a device path protocol
on it. We have to use this device path as stem for the partition
device paths.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
This unit test checks the following protocol services:
ConnectController, DisconnectController,
InstallProtocol, UninstallProtocol,
OpenProtocol, CloseProtcol, OpenProtocolInformation
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Unfortunately we need a forward declaration because both
OpenProtocol and CloseProtocol have to call DisconnectController.
And DisconnectController calls both OpenProtcol and CloseProtocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Add color coding to output:
test section blue
success green
errors red
todo yellow
summary white
others light gray
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
[agraf: Fold in move of set_attribute before the print] Signed-off-by: Alexander Graf <agraf@suse.de>
tools: provide a tool to convert a binary file to an include
For testing EFI disk management we need an in-memory image of
a disk.
The tool file2include converts a file to a C include. The file
is separated into strings of 8 bytes. Only the non-zero strings
are written to the include. The output format has been designed
to maintain readability.
This enhancement is not available when building without EFI support
and neither in the SPL nor in the API example.
A test is provided. It can be executed in the sandbox with command
ut_print.
The development for EFI support in the sandbox is currently in
branch u-boot-dm/efi-working. The branch currently lacks
commit 6ea8b580f06b ("efi_loader: correct DeviceNodeToText
for media types"). Ater rebasing the aforementioned branch on
U-Boot v2018.01 the test is executed successfully.
Without EFI support in the sandbox the test is simply skipped.
Suggested-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
lib/efi* indicates files efi* in directory lib.
lib/efi*/ indicates all files in directories lib/efi*.
Fixes: 623b3a579765 efi_selftest: provide an EFI selftest application Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
efi_selftest: do not cut off u16 strings when printing
Device paths can be very long. Due to a limited output buffer
the output for device paths is cut off. We can avoid this by
directly calling the boottime service with the the device path
string.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Remove coloring code change] Signed-off-by: Alexander Graf <agraf@suse.de>
fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Commit 4f425280fa71 ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.
Jaehoon Chung [Wed, 17 Jan 2018 10:36:58 +0000 (19:36 +0900)]
mmc: fix the wrong disabling clock
When power is off, clock is not disabling.
Because it's passed to 1, mmc->clock should be set to f_min value.
Some drivers can't initialize the eMMC/SD card with current status.
This patch is to fix the disabling clock value to 0.
Fixes: 2e7410d76ad1 ("mmc: disable the mmc clock during power off") Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Guillaume GARDET <guillaume.gardet@free.fr> Tested-by: Anand Moon <linux.amoon@gmail.com>
projects / u-boot / log