Marek Vasut [Thu, 31 May 2018 13:18:18 +0000 (15:18 +0200)]
ARM: rmobile: Point load address to more sane area on Gen3
Point the $loadaddr variable and default load address to a more sane
area, 384 MiB from the start of RAM. This is to avoid all the reserved
memory at the beginning of RAM. The old behavior could still be easily
retained by "setenv loadaddr 0x48080000" . The new setup allows us to
use for example modern fitImage with kernel_noload, so use this as a
new preferred default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Thu, 31 May 2018 13:12:53 +0000 (15:12 +0200)]
ARM: rmobile: Point load address to more sane area on Gen2
Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Tue, 5 Jun 2018 18:21:30 +0000 (20:21 +0200)]
ARM: rmobile: Zap CONFIG_SYS_CLK_FREQ where applicable
The CONFIG_SYS_CLK_FREQ is not used on some of the Gen3 boards,
remove it. Moreover, on Ebisu this actually didn't match the
comment in the config file at all, but since it was not used,
there was no real problem.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alex Kiernan [Thu, 7 Jun 2018 12:20:05 +0000 (12:20 +0000)]
tools: env: Use getline rather than fgets when reading config/script
When reading the config file, or a script file, use getline rather than
fgets so line lengths aren't limited by the size of a compiled in buffer
(128 characters for config, 1024 for scripts).
Rename 'dump' to 'line' so it's clear we're working with a line of text.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Adam Ford [Wed, 6 Jun 2018 19:39:50 +0000 (14:39 -0500)]
AM3517_EVM: Fix Environmental location
The am3517-evm boards stores the environment in NAND, but after merging
various configs, the board was trying to load environment variables from
FAT which would ultimately fail and cause some chatter.
This patch removes the ENV_IS_IN_FAT flag to eliminate the noise.
Alexey Brodkin [Tue, 5 Jun 2018 14:17:57 +0000 (17:17 +0300)]
lib: Add hexdump
Often during debugging session it's very interesting to see
what data we were dealing with. For example what we write or read
to/from memory or peripherals.
This change introduces functions that allow to dump binary
data with one simple function invocation like:
------------------->8----------------
print_hex_dump_bytes("", DUMP_PREFIX_OFFSET, buf, len);
------------------->8----------------
Source of hexdump.c was copied from Linux kernel v4.7-rc2.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Mario Six <mario.six@gdsys.cc> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Stefan Roese <sr@denx.de>
fs: btrfs: Fix not all CHUNK_ITEMs being read from CHUNK_TREE
This causes errors when translating logical addresses to physical:
btrfs_map_logical_to_physical: Cannot map logical address <addr> to physical
btrfs_file_read: Error reading extent
The behavior of btrfs_map_logical_to_physical() is to stop traversing
CHUNK_TREE when it encounters first non-CHUNK_ITEM, which makes
only some portion of CHUNK_ITEMs being read.
Change it to skip over non-chunk items.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com> Cc: Marek Behun <marek.behun@nic.cz> Cc: Sergey Struzh <sergeys@pointgrab.com> Reviewed-by: Marek Behun <marek.behun@nic.cz>
Seung-Woo Kim [Mon, 4 Jun 2018 11:45:54 +0000 (20:45 +0900)]
fs: fat: fix wrong casting to unsigned value of sect_to_cluster()
After the commit 265edc03d5a1 ("fs/fat: Clean up open-coded sector
<-> cluster conversions"), it is hung up writing new file to FAT16
disk with more than 19 files in armv7. It is because result value
of sect_to_cluster() is not proper by casting from signed value to
unsigned value. Fix the wrong casting of sect_to_cluster().
Dennis Gilmore [Tue, 12 Jun 2018 00:39:53 +0000 (19:39 -0500)]
arm: mvebu: Add Helios4 Armada 38x initial support
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Dennis Gilmore <dgilmore@redhat.com> Signed-off-by: Stefan Roese <sr@denx.de>
Bhaskar Upadhaya [Wed, 23 May 2018 05:33:30 +0000 (11:03 +0530)]
board: ls1012a: FRWY-LS1012A board support
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
Ramon Fried [Wed, 30 May 2018 20:09:58 +0000 (23:09 +0300)]
iotrace: add IO region limit
When dealing with a lot of IO regions, sometimes
it makes sense only to trace a specific one.
This patch adds support for region limits.
If region is not set, the iotrace works the same as it was.
If region is set, the iotrace only logs io operation that falls
in the defined region.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ramon Fried [Tue, 5 Jun 2018 21:38:59 +0000 (00:38 +0300)]
bug.h: introduce WARN_ONCE
Add WARN_ONCE definition to allow single time notification
of warnings to the user.
Taken from Linux kernel (4.17) with slight changes
(Removed __section(.data.once))
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
[trini: Drop the musb and dwc3 compat versions] Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Fri, 1 Jun 2018 15:38:21 +0000 (09:38 -0600)]
binman: Add support for adding a name prefix to entries
Sometimes we have several sections which repeat the same entries (e.g. for
a read-only and read-write version of the same section). It is useful to
be able to tell these entries apart by name.
Add a new 'name-prefix' property for sections, which causes all entries
within that section to have a given name prefix.
Simon Glass [Fri, 1 Jun 2018 15:38:20 +0000 (09:38 -0600)]
binman: Add support for outputing a map file
It is useful to be able to see a list of regions in each image produced by
binman. Add a -m option to output this information in a '.map' file
alongside the image file.
Simon Glass [Fri, 1 Jun 2018 15:38:16 +0000 (09:38 -0600)]
binman: Add support for sections
It is useful to be able to split an image into multiple sections,
each with its own size and position, for cases where a flash device has
read-only and read-write portions.
Simon Glass [Fri, 1 Jun 2018 15:38:15 +0000 (09:38 -0600)]
binman: Avoid setting sys.path globally
At present we set the Python path at the start of binman so we can read
modules in the 'etype' directory. This is a bit messy since it affects
'import' statements through binman.
Adjust the code to set the path locally, just where it is needed. Move
the 'entry' module in with the other base modules to help with this. It
makes more sense here anyway since it does not implement an entry type.
Simon Glass [Fri, 1 Jun 2018 15:38:12 +0000 (09:38 -0600)]
binman: Refactor much of the image code into 'section'
We want to support multiple sections within a single image. To do this,
move most of the Image class implementation into a new Section class. An
Image contains only a single Section, but at some point we will support
a new 'section' entry, thus allowing Sections within Sections.
Use the name 'bsection' for the module so we can use 'section' for the
etype module.
Tom Rini [Tue, 22 May 2018 16:24:16 +0000 (12:24 -0400)]
block: Have BLOCK_CACHE default to y in some cases
When dealing with filesystems that come from block devices we can get a
noticeable performance gain in some use cases from having the block
cache enabled. The code paths are valid in other cases when we have BLK
set and may provide wins in raw reads in some use cases, so have this be
default when BLK is enabled.
Baruch Siach [Thu, 7 Jun 2018 09:38:11 +0000 (12:38 +0300)]
mvebu: turris_omnia: add note about i2c slave disable
Code that disables the i2c slave is now in the mvtwsi i2c driver.
Platform must enable DM_I2C to use that code. Add a comment in the code
as a reminder for the planned DM_I2C migration of Turris Omnia.
Baruch Siach [Thu, 7 Jun 2018 09:38:10 +0000 (12:38 +0300)]
i2c: mvtwsi: disable i2c slave on Armada 38x
Equivalent code that disables the hidden i2c0 slave already exists in
the Turris Omnia platform specific code. But this hidden i2c0 slave that
interferes the i2c bus is not board specific. Armada 38x SoCs and at
least some Kirkwood variants are affected as well. Add code to disable
this slave to the i2c bus driver to make it work on all affected
hardware.
Use the bind callback because we want this to always run at boot,
regardless of whether U-Boot uses the i2c bus.
Cc: Rabeeh Khoury <rabeeh@solid-run.com> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Stefan Roese [Tue, 29 May 2018 13:28:54 +0000 (15:28 +0200)]
mtd: ubi: Add missing newlines in ubi_init()
I just stumbled over some cluttered UBI messages. It seems some newline
chars are missing in the current U-Boot UBI source. Lets fix this
in U-Boot as well (Linux has those fixes already).
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Fri, 25 May 2018 13:08:14 +0000 (16:08 +0300)]
board_f: Only reserve memory for U-Boot if we're going to relocate
In case of no relocation we'll just waste some space at the very end
of usable memory area. If target device has very limited amount of memory
(for example 256 kB) this loss will be pretty inconvenient.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Heiko Schocher <hs@denx.de> Cc: York Sun <york.sun@nxp.com> Cc: Stefan Roese <sr@denx.de>
Masahiro Yamada [Thu, 24 May 2018 08:04:57 +0000 (17:04 +0900)]
menu: fix timeout duration
For distro-boot, the TIMEOUT directive in the boot script specifies
how long to pause in units of 1/10 sec. [1]
Commit 8594753ba0a7 ("menu: only timeout when menu is displayed")
corrected this by simply dividing the timeout value by 10 in
menu_interactive_choice().
I see two problems:
- For example, "TIMEOUT 5" should wait for 0.5 sec, but the current
implementation cannot handle the granularity of 1/10 sec.
In fact, it never breaks because "m->timeout / 10" is zero,
which means no timeout.
- The menu API is used not only by cmd/pxe.c but also by
common/autoboot.c . For the latter case, the unit of the
timeout value is _second_ because its default is associated
with CONFIG_BOOTDELAY.
To fix the first issue, use DIV_ROUND_UP() so that the timeout value
is rounded up to the closest integer.
For the second issue, move the division to the boundary between
cmd/pxe.c and common/menu.c . This is a more desirable place because
the comment of struct pxe_menu says:
* timeout - time in tenths of a second to wait for a user key-press before
* booting the default label.
Then, the comment of menu_create() says:
* timeout - A delay in seconds to wait for user input. If 0, timeout is
* disabled, and the default choice will be returned unless prompt is 1.
Sam Protsenko [Mon, 21 May 2018 23:04:21 +0000 (02:04 +0300)]
disk: efi: Correct backing up the MBR boot code
In commit e163a931af34 ("cmd: gpt: backup boot code before writing MBR")
there was added the procedure for storing old boot code when doing "gpt
write". But instead of storing just backup code, the whole MBR was
stored, and only specific fields were replaced further, keeping
everything else intact. That's obviously not what we want.
Fix the code to actually store only old boot code and zero out
everything else. This fixes next testing case:
In case when $loadaddr address and further memory contains 0xff, the
board was bricked (ROM-code probably didn't like partition entries that
were clobbered with 0xff). With this patch applied, commands above don't
brick the board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Cc: Alejandro Hernandez <ajhernandez@ti.com> Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
David Lechner [Sun, 20 May 2018 04:25:04 +0000 (23:25 -0500)]
ARM: legoev3: Move UART enable to early init
This moves the UART init for LEGO MINDSTORMS EV3 to board_early_init_f().
Some console messages were not being printed because the UART was not
enabled until later in the init process.
Signed-off-by: David Lechner <david@lechnology.com>
The SBx81LIFKW boards connect to the internal chassis management network
via a Marvell 88e6097 L2 switch. The chassis connections are direct
serdes on ports 8 and 9 with a RGMII interface on port 10 connected to
the CPU MAC.
For debugging purposes ports 0 and 1 are also taken out to headers on
the board. Because the debug interfaces are sometimes connected to with
straight ribbon cables we need to run them at 10Mbps.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Wed, 30 May 2018 08:14:35 +0000 (20:14 +1200)]
ARM: add SBx81LIFKW board
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Wed, 30 May 2018 08:14:34 +0000 (20:14 +1200)]
ARM: kirkwood: remove automatic I2C config if DM_I2C is enabled
The mach/config.h file would helpfully define CONFIG_SYS_I2C and
CONFIG_SYS_I2C_MVTWSI if CONFIG_CMD_I2C was defined by the board. This
conflicts with the way DM_I2C works. As a transitional measure don't
automatically define these if CONFIG_DM_I2C is defined. It should be
possible to remove this once all kirkwood boards are migrated to DM.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Michael Walle [Tue, 29 May 2018 21:13:20 +0000 (23:13 +0200)]
arm: kirkwood: lsxl: Add SPI driver model support
This patch shows how to enable driver model support for the LS-CHLv2 and
LS-XHL boards.
There are a couple of open questions:
- do I need the u-boot,dm-pre-reloc tags in the device tree?
- should mach/config.h define CONFIG_DM_SEQ_ALIAS?
- how can we split this patch or are there any other pending patches
which does the same and I didn't catch these.
This patch is based on the http://git.denx.de/u-boot-marvell.git (master
branch) and needs the following patches, which are still pending:
https://patchwork.ozlabs.org/patch/909618/
https://patchwork.ozlabs.org/patch/909617/
https://patchwork.ozlabs.org/patch/909973/
Signed-off-by: Michael Walle <michael@walle.cc> Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot / log