ARM: zynq: Move spi node to aligned location

Keep nodes aligned.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Fix defconfig for zybo

Change possition of SPI_FLASH to by align with savedefconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Fix all remaining zynq platform to use stdout-path

Fix console setup for all remaining zynq boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Clean DTSI coding style

Fix minor indentation problems.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Move FLASH_BAR to Kconfig

Clean up config and use Kconfig more.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Enable SPI_FLASH for zc770 xm013 platform

Enable SPI flash.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Define sys prompt for all Zynq boards

Define CONFIG_SYS_PROMPT for all Zynq boards

It was removed by:
"kconfig: add config option for shell prompt"
(sha1: 181bd9dc61d2da88b78f1c1138a685dae39354d6)

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Do not select options if SPL is not enabled

Zynq setups some default options for SPL but not all targets are
enabling SPL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: zynq: Remove memory division by 2 for ECC case

For ECC case u-boot divided memory by 2 because one u-boot could be used
for both cases when ECC is off or on.
Remove this division and make sure that dts file contain the correct
memory size when ECC is enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

mmc: zynq_sdhci: Added qurik to disable high speed

Add quirk to disable high speed incase the high
speed was broken.This solves the issue where the
the controller is used in High Speed Mode and the
the hold time requirement for the JEDEC/MMC 4.41
specification is NOT met.
This timing issue is not on all boards and hence
provided config option to enable it when required.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Emil Lenchak <emill@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

mmc: sdhci: Clear high speed if not supported

Clear high speed bit if it was not supported by
the driver.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Emil Lenchak <emill@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

sdhci: zynq: Remove hardcoded value zero as min frequency

Remove hardcoded value zero as min frequency and
use config option CONFIG_ZYNQ_SDHCI_MIN_FREQ
defined in board config

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: zynq: Change MDC setup for arm64

MDC setting depends on pclk input clocks which varies across SoC. This
driver is used by xilinx zynq and zynqmp SOC.
Input clock frequence on silicon is 125MHz where divider 64 put
frequency below 2.5MHz requires by spec (125/64=1.95).

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: phy: ti: Enable automatic crossover mode

Enable automatic crossover cable detection.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

serial: zynq: Fix address reading from DM

Use dev_get_addr() instead of reading reg base directly in the driver.
Core function is also more robust.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

serial: zynq: Extend compatible string list

ZynqMP is using updated core with cdns,uart-r1p12 compatible string.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

fpga: Fix compilation warnings

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

fpga: Add bitstream type BIT_NONE

Add bitstream type BIT_NONE to the bitstream type
enum. This might be useful while loading bitstreams
in respective drivers.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

fpga: xilinx: Check for substring in device ID validation

Check for substrings in deviceID validation check
so that it can support xa bitstreams also.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Fix board_init calling sequence

board_init() is in final elf file but it is not called at all.
Use board_init_late() instead and call gpio_init() from it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Enable HUSH via Kconfig

Cleanup board file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Read information about RAM from DT

Do not setup ram start/size in board file. Read it from DT instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Remove empty file - cpu.c

No need to have empty unused file in architecture code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Move CONFIG_NETCONSOLE to Kconfig

Cleanup board file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Remove CONFIG_FIT from board file

And enable it via defconfig by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Remove systemace from board file

Systemace is ancient IP which is not tested. Remove it from default
configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Move eth configuration to Kconfig

Cleanup board specific file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Enable axi emac via Kconfig

Enable driver by default for all platforms.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: emaclite: Move emaclite to Kconfig

Add PHYLIB and MII dependencies and enable it by default for Microblaze.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Let core to handle received packet

Pass pointer to core to handle packet.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: emaclite: Rename start and stop functions

Rename start and stop functions to align with DM functions names.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: emaclite: Move driver to DM

Move driver to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Use indirect access in emaclite_recv

When IP is configured with pong buffers, IP is receiving packets to ping
and then to pong buffer and than ping again.
The original logic in the driver remains there that when ping buffer is
free, pong buffer is checked too and return if both are free.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: emaclite: Use indirect reg access in send

The original logic in the driver was exchanging buffers which are used for
sending packet and tx_ping and tx_pong buffers were exchanged all the
time to ensure that IP has enough time to send the packet out.
Based on this "feature" send function was using nextbuffertouse variable
to save which buffer should be used.
Before this algorithm was called driver checked that there is free
buffer available.
This checking remains in the driver but driver tries to use tx_ping
first if available. If not, tx_pong buffer is used instead.
To reach this code the original condition is met that at least one of the
buffer should be available.
Testing doesn't show any performance drop when this patch is applied.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Remove XEL_TSR_XMIT_ACTIVE_MASK flag

This flag is not documented anywhere in the latest documentation that's
why this patch removes it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Fix logic around available TX buffers

Simplify logic how to find out if there is free TX buffer.
Both buffers are checked all the time that's why logic around order
can be removed.
Also add check when only one buffer is available.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Use indirect register access for TX reset

Move to use indirect register access when timeout expires for resetting
TX buffers.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Use indirect register access for rx_ping/pong

Do initialization via indirect register access.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: emaclite: Use indirect register access for tx_ping/pong

Do initialization via indirect register access.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Convert MDIO to use register offset

Use u-boot coding style how to setup and access MDIO bus.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Add MDIO support to driver

Add MDIO support before move to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: emaclite: Remove ancient OF probe function

Prepare for DM move.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: Add axi emac to Kconfig

Also add dependency on PHYLIB and MII which is required.
Clean PHYLIB dependency from the driver too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Rename start, stop, write_hwaddr functions

Rename few functions to fit to the new name convention used by DM.

Suggested-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: axi_emac: Split recv from free_pkt

Call net_process_received_packet() by core.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Enable access to MDIO in probe

Detect phy when driver probes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Move driver to DM

Move driver to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Pass private structure where possible

Use axidma_priv instead of ethdevice in preparation of the DM move.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: axi_emac: Pass private structure to phyread/phywrite

Prepare for move to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Put iobase to private structure

Saving iobase directly to private structure helps with moving to DM.
There is an option to load iobase from pdata but it is additional load.
Pointer to private structure is available all the time.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Pass directly pointer to register space

Simplify mdio_wait function by passing regs directly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Show phy address instead of register content

Fix debug message.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: axi_emac: Fix parentheses around operand !

Fix these compilation warning by proper grouping:
In function 'axi_dma_init': drivers/net/xilinx_axi_emac.c:391:7:
warning: suggest parentheses around operand of '!' or change '&' to '&&'
or '!' to '~' [-Wparentheses]
    if (!(in_be32(&priv->dmatx->control) |
        ^
In function 'axiemac_send': drivers/net/xilinx_axi_emac.c:501:21:
warning: suggest parentheses around operand of '!' or change '&' to '&&'
or '!' to '~' [-Wparentheses]
  while (timeout && (!in_be32(&priv->dmatx->status) &

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

microblaze: Enable MICREL_KSZ9021

To solve enabling ETH_DM where ksz90x1_reg_field is defined only when
additional Micrel type is defined.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Wire-up debug_uart in asm

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Remove unused I2C macros

There is no i2c driver in the current u-boot.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Enable PHYLIB via Kconfig

Cleanup board configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Do not print eth device when DM_ETH is enabled

Doing the same fix as is done for ARM by:
"Avoid calling print_eths() with driver model"
(sha1: ff97380015b6b5d7d6267417a1cd6fc0e67b81bc)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

microblaze: Enable uart16550 DM by default

Microblaze is uses uartlite or uart16550 as console drivers.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

serial: uartlite: Add uartlite to Kconfig

- Move config option out of board file.
- Remove uartlite address from config file

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>

serial: uartlite: Add support for debug console

Add support for debug console.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>

serial: uartlite: Move driver to DM

Enable SPL DM too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>

microblaze: Move baudrate setting out driver selection

Preparation of moving to DM. Uartlite ignores baudrate setting.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Remove CONSOLE_ARG

Take it from DT instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ppc: xilinx-ppc4xx-generic: Update xparameters.h

-Remove UART address (It is now part of the dts).
-Include dummy ns16550 clock
-Fix address to last test

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

configs/xilinx-ppc440-generic: Typos and size

-Fix typos (runnining -> running)
-Increase default size

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

configs/xilinx-ppc405-generic: Typos and size

-Fix typos (runnining -> running)
-Increase default size

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: dts: Add device tree for xilix-ppc4xx-generic

Add device tree example file for xilinx-ppc440-generic and
xilinx-ppc405-generic

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: xilinx-ppc405-generic: Cleanout header files

Now that there is only one header file for all ppc405 files, merge
header files.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: xilinx-ppc440-generic: Cleanout header files

Now that there is only one header file for all ppc440 files, merge
header files.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: ppc405: ppc405-generic_flash_defconfig

Remove redundant defconfig file. Boot via flash can be configured via
Kconfig.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: ppc440: ppc440-generic_flash_defconfig

Remove redundant defconfig file. Boot via flash can be configured via
Kconfig.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: pp440-generic: Simplify Makefile

As a result of the specific board removal, the Makefiles can be
simplified.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: pp405-generic: Simplify Makefile

As a result of the specific board removal, the Makefiles can be
simplified.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

mailaddr: Update mail address

The old mail address will stop working soon.
Update it all the files

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

.mailmap: Add all the mail alias for Ricardo Ribalda

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

xilinx-ppc440: Remove support for v5fx30teval

It is just a specialized version of xilinx-ppc440

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: xilinx-ppc405: Remove support for fx12mm

It is just a specialized version of the xilinx-ppc405

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

ppc: xilinx-ppc440: Remove support for ml507

ml507 is just a specialized version of the xilinx-ppc440-generic

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

mvtwsi: Fix breakage introduced by "Fix mvtwsi not working on sun6i and newer sunxi SoCs"

"Fix mvtwsi not working on sun6i and newer sunxi SoCs" includes the following:

@@ -189,7 +200,8 @@ static int twsi_start(struct i2c_adapter *adap, int expected_status)
  /* globally set TWSIEN in case it was not */
  twsi_control_flags |= MVTWSI_CONTROL_TWSIEN;
  /* assert START */
- writel(twsi_control_flags | MVTWSI_CONTROL_START, &twsi->control);
+ twsi_control_flags |= MVTWSI_CONTROL_START | MVTWSI_CONTROL_CLEAR_IFLG;
+ writel(twsi_control_flags, &twsi->control);
  /* wait for controller to process START */
  return twsi_wait(adap, expected_status);
 }

The modification of twsi_control_flags done here was introduced while
merging to fix a line > 80 chars, but twsi_control_flags is a global variable
and should not be modified like this here, this commit fixes this, restoring
mvtwsi functionality.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Bananapro: Set LDO4 to 2.5V

According to the Bananapro schematic VDD25-SATA either comes from a
dedicated WL2003E25-5 LTO, or it is connected to LDO4 via a
0 Ohm resistor.

In practice it seems that LDO4 is used, so enable it and set it to 2.5V.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: power: axp818: Enable support for ALDOs

Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boards continue to work because the AXP818 is designed
to pair with the A83T/H8, and the default voltages match the reference
design's requirements.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: h8_homlet_v2: Drop LDO settings from defconfig

The LDO settings in this defconfig are either wrong (ALDOs must not be 0)
or the same as Kconfig defaults.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

power: axp818: Add support for DLDO and ELDO regulators

AXP818 provides an array of LDOs to provide power to various peripherals.
None of these regulators are critical.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

power: axp: merge separate DLDO functions into 1

Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

power: axp818: Remove duplicate register definition macros

Some of the register definitions are duplicated. Drop them.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Add suport for A83T based Banana-pi M3 Board

Add dts and defconfig for Banana-pi M3 board.

It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Add support for LPDDR3 for A83T

Banana-pi M3 has LPDDR3 DRAM. this adds support for LPDDR3 for A83T.
Mostly the timing parameters are different from DDR3.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Groundwork to support new dram type for A83T

Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.

This adds groundwork to support for new DRAM type for A83T.

Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Redundant code cleanup from a83t dram init

This removes the redundant lines of code from mctl_sys_init.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable booting non-secure and virtualization for H3

Now that we support PSCI and various security switches, we can let
U-boot boot Linux into non-secure and HYP mode.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Support PSCI ops on Allwinner H3

H3 has the same power sequencing procedure as the A31/A31s, which
includes the power clamps.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Support H3 CCU security switches

H3's CCU includes some switches which disable non-secure access to some
of the more critical clock controls, such as MBUS, PLLs, and main
platform busses.

Configure them to enable non-secure access.

For now the only SoC that has this feature is the H3. For other
platforms just use a default (weak) empty function so things do
not break.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Support Secure Memory Touch Arbiter (SMTA) in sun8i H3

Secure Memory Touch Arbiter is the same thing as the TrustZone
Protection Controller found on A31/A31s.

Access to many peripherals on the H3 can be controlled by the SMTA,
and the settings default to secure access only.

This patch supports the new settings, and sets them to allow non-secure
access.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Implement poweroff support for axp221 pmic

Adds poweroff support for axp221 pmic.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Implement poweroff support for axp209 pmic

Adds poweroff support for axp209 pmic.

Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Implement poweroff support for axp152 pmic

Adds poweroff support for axp152 pmic.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Merge branch 'master' of git://git.denx.de/u-boot-video

video: add CONFIG_I2C_EDID and disable CONFIG_DISPLAY by default

Enabling CONFIG_DISPLAY breaks building for some architectures
(microblaze-generic), so we disable CONFIG_DISPLAY in Kconfig
by default and enable this option in defconfigs. CONFIG_DISPLAY
depends on CONFIG_I2C_EDID, so add and enable it in defconfigs, too.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>