Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.
Sandeep Paulraj [Sat, 30 Aug 2008 22:39:46 +0000 (00:39 +0200)]
ARM DaVinci: Changing function names for EMAC driver
DM644x is just one of a series of DaVinci chips that use the EMAC driver.
By replacing all the function names that start with dm644x_* to davinci_*
we make these function more portable. I have tested this change on my EVM.
DM6467 is another DaVinci SOC which uses the EMAC driver and i will
be sending patches that add DaVinci DM6467 support to the list soon.
- memsetup.s is changed/merged to lowlevel_init.S
memsetup.S has a global label memsetup that just returns back to caller
- memsetup global label is changed/merged to lowlevel_init
This label is not called from anywhere.
Kumar Gala [Fri, 25 Jul 2008 18:31:05 +0000 (13:31 -0500)]
mpc85xx: Add support for the MPC8536DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by: Dejan Minic <minic@freescale.com> Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 12 Aug 2008 16:14:19 +0000 (11:14 -0500)]
mpc85xx: Add support for the MPC8536
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by: Dejan Minic <minic@freescale.com> Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Dave Liu <daveliu@freescale.com>
Andrew Dyer [Tue, 26 Aug 2008 22:03:38 +0000 (17:03 -0500)]
dm9000 remove dead external phy support, gpio fix
dm9000 has code to detect and initialize external phy parts, but later
on in the code the part is forced to use the internal phy
unconditionally. Remove the unused/untested code.
change the GPIO initialization so that only the GPIO used as an
internal phy reset (hardwired in the chip) is set as an output. The
remaining GPIO need to be handled by board specific code to prevent
possible drive conflicts. Set as inputs for safety.
replace a few magic numbers with defines
Signed-off-by: Andrew Dyer <adyer@righthandtech.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Peter Tyser [Tue, 26 Aug 2008 16:17:48 +0000 (11:17 -0500)]
Standardize bootp, tftpboot, rarpboot, dhcp, and nfs command descriptions
cmd_net.c command descriptions were updated to describe the optional
hostIPaddr argument. The dhcp command help message was also updated
to more closely reflect the other commands in cmd_net.c
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Kumar Gala [Tue, 26 Aug 2008 20:01:32 +0000 (15:01 -0500)]
FSL DDR: Add DDR2 DIMM paramter support
Compute DIMM parameters based upon the SPD information.
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 26 Aug 2008 20:01:30 +0000 (15:01 -0500)]
FSL DDR: Add DDR1 DIMM paramter support
Compute DIMM parameters based upon the SPD information in spd.
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 26 Aug 2008 20:01:29 +0000 (15:01 -0500)]
FSL DDR: Rewrite the FSL mpc8xxx DDR controller setup code.
The main purpose of this rewrite it to be able to share the same
initialization code on all FSL PowerPC products that have DDR
controllers. (83xx, 85xx, 86xx).
The code is broken up into the following steps:
GET_SPD
COMPUTE_DIMM_PARMS
COMPUTE_COMMON_PARMS
GATHER_OPTS
ASSIGN_ADDRESSES
COMPUTE_REGS
PROGRAM_REGS
This allows us to share more code an easily allow for board specific code
overrides.
Additionally this code base adds support for >4G of DDR and provides a
foundation for supporting interleaving on processors with more than one
controller.
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Signed-off-by: Becky Bruce <becky.bruce@freescale.com> Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Aug 2008 13:24:45 +0000 (08:24 -0500)]
bootm: refactor do_reset and os boot function args
There is no need for each OS specific function to call do_reset() we
can just do it once in bootm. This means its feasible on an error for
the OS boot function to return.
Also, remove passing in cmd_tbl_t as its not needed by the OS boot
functions. flag isn't currently used but might be in the future so
we left it alone.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Aug 2008 13:24:43 +0000 (08:24 -0500)]
fdt: refactor initrd related code
Created a new fdt_initrd() to deal with setting the initrd properties
in the device tree and fixing up the mem reserve. We can use this
both in the choosen node handling and lets us remove some duplicated
code when we fixup the initrd info in bootm on PPC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Aug 2008 13:24:41 +0000 (08:24 -0500)]
bootm: refactor image detection and os load steps
Created a bootm_start() that handles the parsing and detection of all
the images that will be used by the bootm command (OS, ramdisk, fdt).
As part of this we now tract all the relevant image offsets in the
bootm_headers_t struct. This will allow us to have all the needed
state for future sub-commands and lets us reduce a bit of arch
specific code on SPARC.
Created a bootm_load_os() that deals with decompression and loading
the OS image.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Aug 2008 13:24:40 +0000 (08:24 -0500)]
bootm: move lmb into the bootm_headers_t structure
To allow for persistent state between future bootm subcommands we
need the lmb to exist in a global state.
Moving it into the bootm_headers_t allows us to do that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Aug 2008 13:24:39 +0000 (08:24 -0500)]
bootm: Set working fdt address as part of the bootm flow
Set the fdt working address so "fdt FOO" commands can be used as part
of the bootm flow. Also set an the environment variable "fdtaddr"
with the value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Aug 2008 13:24:37 +0000 (08:24 -0500)]
bootm: refactor ramdisk locating code
Move determing if we have a ramdisk and where its located into the
common code. Keep track of the ramdisk start and end in the
bootm_headers_t image struct.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Randy Vinson [Wed, 13 Aug 2008 18:44:57 +0000 (11:44 -0700)]
mpc7448hpc2: Fix PCI I/O space mapping.
PCI I/O space is currently mapped 1:1 at 0xFA000000. Linux requires
PCI I/O space to start at 0 on the PCI bus. This patch maps PCI I/O
space such that 0xFA000000 in the processor's address space maps to 0
on the PCI I/O bus.
Signed-off-by Randy Vinson <rvinson@mvista.com> Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Ira W. Snyder [Fri, 22 Aug 2008 18:00:14 +0000 (11:00 -0700)]
mpc83xx: add PCISLAVE support to 83XX_GENERIC_PCI setup code
This adds a helper function to unlock the PCI configuration bit, so that
any extra PCI setup (such as outbound windows, etc.) can be done after
using the 83XX_GENERIC_PCI code to set up the PCI bus.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Stefan Roese [Wed, 20 Aug 2008 18:29:38 +0000 (20:29 +0200)]
RTC: Fix Makefile problem with COBJS-$(CONFIG_RTC_DS1307 || CONFIG_RTC_DS1338)
This "||" doesn't seem to work. Now using the idea suggest by Scott Wood
to combine both config options into one line. This even allows defining
both options and not generating the target object twice.
- According to ARM Dual-Timer Module (SP804) TRM (ARM DDI0271),
-- Timer Value Register @ TIMER Base + 4 is Read-only.
-- Prescale Value (Bits 3-2 of TIMER Control register)
can only be one of 00,01,10. 11 is undefined.
-- CFG_HZ for Versatile board is set to
#define CFG_HZ (1000000 / 256)
So Prescale bits is set to indicate
- 8 Stages of Prescale, Clock divided by 256
- The Timer Control Register has one Undefined/Shouldn't Use Bit
So we should do read/modify/write Operation
Gerald Van Baren [Fri, 22 Aug 2008 18:37:05 +0000 (14:37 -0400)]
Add note on dereferencing /aliases pointers
Replace the "must quote special characters" note with a hint on
how to dereference /aliases pointers by omitting the leading "/".
This feature was introduced by Kumar Gala as a libfdt enhancement
in commit ed035708235332c3c117ee3bb1a426063f03cfcb.
Kumar Gala [Thu, 14 Aug 2008 13:28:19 +0000 (08:28 -0500)]
libfdt: Add support for using aliases in fdt_path_offset()
If the path doesn't start with '/' check to see if it matches some alias
under "/aliases" and substitute the matching alias value in the path
and retry the lookup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
David Gibson [Wed, 6 Aug 2008 04:50:49 +0000 (14:50 +1000)]
libfdt: Implement fdt_get_property_namelen() and fdt_getprop_namelen()
As well as fdt_subnode_offset(), libfdt includes an
fdt_subnode_offset_namelen() function that takes the subnode name to
look up not as a NUL-terminated string, but as a string with an
explicit length. This can be useful when the caller has the name as
part of a longer string, such as a full path.
However, we don't have corresponding 'namelen' versions for
fdt_get_property() and fdt_getprop(). There are less obvious use
cases for these variants on property names, but there are
circumstances where they can be useful e.g. looking up property names
which need to be parsed from a longer string buffer such as user input
or a configuration file, or looking up an alias in a path with
IEEE1275 style aliases.
So, since it's very easy to implement such variants, this patch does
so. The original NUL-terminated variants are, of course, implemented
in terms of the namelen versions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
David Gibson [Tue, 29 Jul 2008 04:51:22 +0000 (14:51 +1000)]
libfdt: Forgot one function when cleaning the namespace
In commit b6d80a20fc293f3b995c3ce1a6744a5574192125, we renamed all
libfdt functions to be prefixed with fdt_ or _fdt_ to minimise the
chance of collisions with things from whatever package libfdt is
embedded in, pulled into the libfdt build via that environment's
libfdt_env.h.
Except... I missed one. This patch applies the same treatment to
_stringlist_contains(). While we're at it, also make it static since
it's only used in the same file.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
David Gibson [Wed, 9 Jul 2008 04:10:24 +0000 (14:10 +1000)]
libfdt: Increase namespace-pollution paranoia
libfdt is supposed to easy to embed in projects all and sundry.
Often, it won't be practical to separate the embedded libfdt's
namespace from that of the surrounding project. Which means there can
be namespace conflicts between even libfdt's internal/static functions
and functions or macros coming from the surrounding project's headers
via libfdt_env.h.
This patch, therefore, renames a bunch of libfdt internal functions
and macros and makes a few other chances to reduce the chances of
namespace collisions with embedding projects. Specifically:
- Internal functions (even static ones) are now named _fdt_*()
- The type and (static) global for the error table in
fdt_strerror() gain an fdt_ prefix
- The unused macro PALIGN is removed
- The memeq and streq macros are removed and open-coded in the
users (they were only used once each)
- Other macros gain an FDT_ prefix
- To save some of the bulk from the previous change, an
FDT_TAGALIGN() macro is introduced, where FDT_TAGALIGN(x) ==
FDT_ALIGN(x, FDT_TAGSIZE)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
David Gibson [Mon, 7 Jul 2008 00:14:15 +0000 (10:14 +1000)]
dtc: Enable and fix -Wcast-qual warnings
Enabling -Wcast-qual warnings in dtc shows up a number of places where
we are incorrectly discarding a const qualification. There are also
some places where we are intentionally discarding the 'const', and we
need an ugly cast through uintptr_t to suppress the warning. However,
most of these are pretty well isolated with the *_w() functions. So
in the interests of maximum safety with const qualifications, this
patch enables the warnings and fixes the existing complaints.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
David Gibson [Mon, 7 Jul 2008 00:10:48 +0000 (10:10 +1000)]
dtc: Enable and fix -Wpointer-arith warnings
This patch turns on the -Wpointer-arith option in the dtc Makefile,
and fixes the resulting warnings due to using (void *) in pointer
arithmetic. While convenient, pointer arithmetic on void * is not
portable, so it's better that we avoid it, particularly in libfdt.
Also add necessary definition of uintptr_t needed by David Gibson's
changeset "dtc: Enable and fix -Wpointer-arith warnings" (the definition
comes from stdint.h, which u-boot doesn't have). -- gvb
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
projects / u-boot / log