MMC may wrongly regconize 2GB eMMC as high capacity
Hi Terry,
> So I guess:
> mmc_init calls mmc_send_op_cond that set high_capacity,
> than it calls mmc_startup, that, with MMC_CMD_SEND_CSD command, set
> the capacity, using values in CSD register.
> So I guess that mmc_change_freq should not recalculate high_capacity.
>
> It seems better, isn't it?
>
> Regards,
> Raffaele
>
Finally I think that it is enough to apply the following patch in order
to fix the issue.
Regards,
Raffaele
Signed-off-by: Andy Fleming <afleming@freescale.com>
Defining CONFIG_MMC_TRACE in the include board file it is possible to activate
a tracing support.
This code helps in case of eMMC hw failure or to investigate possible eMMC
initialization issues.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: Andy Fleming <afleming@freescale.com>
The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: Andy Fleming <afleming@freescale.com>
mmc: checking status after commands with R1b response
It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: Andy Fleming <afleming@freescale.com>
As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error
would yield the first error return instead of TIMEOUT.
By swapping the test TIMEOUTs are reported as such
An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define
but as that one might be less desired I've opted for the simplest solution
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Wolfgang Wegner [Fri, 23 Apr 2010 05:43:12 +0000 (05:43 +0000)]
add CONFIG_SPI_IDLE_VAL for cf_spi.c to allow use of spi_mmc
This patch adds CONFIG_SPI_IDLE_VAL to cf_spi.c
The default setting is 0x0 to behave same as current version, in case
CONFIG_SPI_MMC is set, the value is set to 0xFFFF (all ones). In either
case, the value can be overwritten by board configuration.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Andy Fleming <afleming@freescale.com>
Matt Waddel [Thu, 24 Feb 2011 16:35:23 +0000 (16:35 +0000)]
MMC: Max blocks value adjustable
The maximum blocks value was hardcoded to 65535 due to a 16 bit
register length. The value can change for different platforms.
This patch makes the default the current value of 65535, but it
is configurable for other platforms.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
Lei Wen [Tue, 15 Feb 2011 08:56:40 +0000 (16:56 +0800)]
disk/part.c: fix potential stack overflow bug
If the param pass to get_dev is not the one defined in the block_drvr,
it could make uboot becomes unstable, for it would continue run after
search complete the block_drvr table.
Remy Bohmer [Sat, 12 Feb 2011 18:06:26 +0000 (19:06 +0100)]
Add support for dataflash to U-boot environment settings tool.
* The sector size for SPI-dataflash (like AT45 flashes) are not always
a power-of-2. So, the sector calculations are rewritten such that it
works for either power-of-2 as any size sectors.
* Make the flash sector size optional in case it is the same value as
the environment size.
Macpaul Lin [Tue, 12 Apr 2011 05:04:02 +0000 (13:04 +0800)]
ftwdt010_wdt: move header to include/faraday and enhance
1. Move header to include/faraday
2. Fix include path in ftwdt010_wdt.c
3. Fix function prototype and declaration to
- ftwdt010_wdt_settimeout
- ftwdt010_wdt_reset
- ftwdt010_wdt_disable
4. Add "#if definde (CONFIG_HW_WATCHDOG)" let user have flexibilty
to choose which better to his product.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
---8<---
cmd_bdinfo.c:458: warning: initialization from incompatible pointer type
--->8---
There was a prototype change in 54841ab50c20d6fa6c9cc3eb826989da3a22d934 for
argv[] pointer type to const. This change was not made for AVR32 cause this
code came in later by a merge.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
---8<---
cmd_nvedit.c: In function 'do_env_export':
cmd_nvedit.c:663: warning: format '%zX' expects type 'size_t', but argument 3 has type 'ssize_t'
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Wolfgang Denk [Fri, 4 Feb 2011 13:25:17 +0000 (14:25 +0100)]
Make STANDALONE_LOAD_ADDR configurable per board
Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR
and allow that the architecture-specific default value gets
overwritten by defining the value in the board header file.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp> Cc: Daniel Hellstrom <daniel@gaisler.com> Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Loïc Minier [Thu, 3 Feb 2011 14:07:01 +0000 (15:07 +0100)]
Drop config.h include in tools/imximage.h
"make tools-all" should allow building tools such as mkimage and the new
imximage without any config, but imximage.c currently fails to build
with:
imximage.h:27:20: error: config.h: No such file or directory
config.h is not needed in imximage.h nor in imximage.c, and imximage.h
is only included from imximage.c, so drop this include to fix the build.
Aaron Williams [Tue, 1 Feb 2011 03:55:50 +0000 (19:55 -0800)]
Fix min/max macros in include/common.h
There is a bug in the min and max macros in common.h which occurs if
Y is a larger type than X. For example, if Y is a 64-bit value and X
is a 32-bit value then Y will be truncated to 32-bits. This fix
matches what is done in the Linux kernel but without the additional
type checking present in the kernel version.
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Andreas Huber [Tue, 25 Jan 2011 10:26:15 +0000 (11:26 +0100)]
ppc, mgcoge: add DIP switch detection
This reads the DIP switch on mgcoge. The DIP switch is connected to
the BFTICU (0x40000089) FPGA. If the DIP switch is set the environment
variable 'actual_bank' is set to 0 and starts the SW in bank0.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Holger Brunck [Tue, 25 Jan 2011 08:57:19 +0000 (09:57 +0100)]
arm, keymile: remove unneeded code
On first HW versions the BOCO FPGA was behind a MUX device. These
HW versions are not supported anymore. And therefore this code can
be removed, it is already unused.
-msingle-pic-base is a new gcc option for ppc and
it reduces the size of my u-boot with 6-8 KB.
While at it, add -fno-jump-tables too to save a
few more bytes.
-msingle-pic-base will be in gcc 4.6, however
backported patches are available at
http://bugs.gentoo.org/show_bug.cgi?id=347281
The -fPIC flag belongs with -mrelocatable, move it there.
Also change -fPIC to -fpic as this produces smaller
binaries.
However, currently -mrelocatable promotes -fpic to -fPIC, a
fix for this is in upcoming gcc 4.6 or you can apply this small
patch to gcc:
diff --git a/gcc/config/rs6000/sysv4.h b/gcc/config/rs6000/sysv4.h
index 8da8410..e4b8280 100644
--- a/gcc/config/rs6000/sysv4.h
+++ b/gcc/config/rs6000/sysv4.h
@@ -227,7 +227,8 @@ do { \
} \
\
else if (TARGET_RELOCATABLE) \
- flag_pic = 2; \
+ if (!flag_pic) \
+ flag_pic = 2; \
} while (0)
Ben Gardiner [Tue, 11 Jan 2011 19:48:17 +0000 (14:48 -0500)]
ea20: fix undefined PHY_* errors
This patch fixes ea20 after 8ef583a0351590a91394499eb5ca2ab8a703d959 where
the u-boot custom PHY_ macros were replaced with those of linux/mii.h MII_
definitions except in the RMII support for davinci_emac. Probably also due to
the merge path of changes in 2010.12.
Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca> CC: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
Ben Gardiner [Tue, 11 Jan 2011 19:48:16 +0000 (14:48 -0500)]
ea20: fix libea20.o not found
This patch fixes ea20 after commit 6d8962e814c15807dd6ac5757904be2a02d187b8
where $(obj)lib$(BOARD).a was changed to $(obj)lib$(BOARD).o in almost all the
Makefiles except ea20, probably due to merge path of the changes in 2010.12.
Mike Frysinger [Mon, 10 Jan 2011 07:20:12 +0000 (02:20 -0500)]
sf: unify status polling for ready bit
All of the spi flash drivers implement the status register polling for
detecting the device ready state, so unify them all in a new helper
function -- spi_flash_wait_ready.
Shaohui Xie [Wed, 16 Mar 2011 02:10:32 +0000 (10:10 +0800)]
powerpc/85xx: Add PBL boot from SPI flash support on P4080DS
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: Chunhe Lan <b25806@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jiang Yutang [Fri, 4 Mar 2011 02:25:54 +0000 (10:25 +0800)]
powerpc/85xx: Add support usb2/etsec and tdm/audio pin multiplex on P1022DS
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds
Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Fri, 25 Mar 2011 19:11:48 +0000 (14:11 -0500)]
p4080ds: add README.p4080ds which documents the "serdes" hwconfig option
Add documentation for the "serdes" hwconfig option, which is used to
specify the status of SerDes banks two and three for the SERDES8 erratum
work-around.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 8 Apr 2011 07:46:39 +0000 (02:46 -0500)]
powerpc/85xx: Drop CONFIG_VIDEO support on corenet_ds boards
We don't really ever use Video cards on corenet_ds style boards and its
bloating our image which is close the its max size. Drop support and
also kill some defines for non-PNP PCI which we never use.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM
and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more
appropriate CONFIG_SYS prefix as well as be consistent with 83xx.
Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mike Frysinger [Fri, 24 Dec 2010 19:46:12 +0000 (14:46 -0500)]
Blackfin: turn off caches when self initializing
When bootstrapping ourselves on the fly at runtime (via "go"), we need to
turn off the caches to avoid taking software exceptions. Since caches
need CPLBs and CPLBs need exception handlers, but we're about to rewrite
the code in memory where those exception handlers live, we need to turn
off caches first.
This new code also encourages a slight code optimization by storing the
MMR bases in dedicated registers so we don't have to fully load up the
pointer regs multiple times.
Mike Frysinger [Fri, 24 Dec 2010 18:19:25 +0000 (13:19 -0500)]
Blackfin: only check for os log when we have external memory
If the part has no external memory configured, then there will be no os
log for us to check, and any attempt to access that memory will trigger
hardware errors.
Mike Frysinger [Fri, 24 Dec 2010 17:48:16 +0000 (12:48 -0500)]
Blackfin: fix bd_t handling
The recent global data changes (making the size autogenerated) broke the
board info handling on Blackfin ports as we were lying and lumping the
bd_t size in with the gd_t size. So use the new dedicated bd_t size to
setup its own address in memory.
Have CONFIG_ENV_ADDR be based on CONFIG_ENV_OFFSET rather than the other
way around so that we can use CONFIG_ENV_OFFSET during build. It also
avoids a little address duplication.
Haiying Wang [Fri, 11 Feb 2011 07:25:30 +0000 (01:25 -0600)]
powerpc/85xx: Add P1021 specific QE and UEC support
P1021 has some QE pins which need to be set in pmuxcr register before
using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and
UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to
be released after MII access because QE12 pin is muxed with LBCTL signal.
Also added relevant QE support defines unique to P1021.
The P1021 QE is shared on P1012, P1016, and P1025.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Tue, 15 Feb 2011 23:09:19 +0000 (17:09 -0600)]
powerpc: clean up DIU macro definitions for Freescale reference boards
Clean up the macro defintions used to enable DIU (video) support on the
MPC8610HPCD and the MPC5121ADS so that they look more like the P1022DS,
which is newer. Add software cursor support to all three boards.
Also document the CONFIG_FSL_DIU_FB in the README.
Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jerry Huang [Mon, 24 Jan 2011 17:09:54 +0000 (17:09 +0000)]
powerpc/85xx: Enable eSDHC boot support on P2020 DS
We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mingkai Hu [Mon, 24 Jan 2011 17:09:55 +0000 (17:09 +0000)]
env_mmc: Allow board code to override the environment address
On some boards the environment may not be located at a fixed address in
the MMC/SDHC card. This allows those boards to implement their own
means to report what address the environment is located at.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kyle Moffett [Mon, 28 Mar 2011 15:35:48 +0000 (11:35 -0400)]
mpc8xxx: DDR2/DDR3: Clean up DIMM-type switch statements
The numeric constants in the switch statements are replaced by #defines
added to the common ddr_spd.h header. This dramatically improves the
readability of the switch statments.
In addition, a few of the longer lines were cleaned up, and the DDR2
type for an SO-RDIMM module was added to the DDR2 switch statement.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Kim Phillips <kim.phillips@freescale.com> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kyle Moffett [Tue, 15 Mar 2011 15:23:47 +0000 (11:23 -0400)]
fsl_ddr: Don't use full 64-bit divides on 32-bit PowerPC
The current FreeScale MPC-8xxx DDR SPD interpreter is using full 64-bit
integer divide operations to convert between nanoseconds and DDR clock
cycles given arbitrary DDR clock frequencies.
Since all of the inputs to this are 32-bit (nanoseconds, clock cycles,
and DDR frequencies), we can easily restructure the computation to use
the "do_div()" function to perform 64-bit/32-bit divide operations.
On 64-bit this change is basically a no-op, because do_div is
implemented as a literal 64-bit divide operation and the instruction
scheduling works out almost the same.
On 32-bit PowerPC a fully accurate 64/64 divide (__udivdi3 in libgcc) is
over 1.1kB of code and thousands of heavily dependent cycles to compute,
all of which is linked from libgcc. Another 1.2kB of code comes in for
the function __umoddi3.
It should be noted that nothing else in U-Boot or the Linux kernel seems
to require a full 64-bit divide on my 32-bit PowerPC.
Build-and-boot-tested on the HWW-1U-1A board using DDR2 SPD detection.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Acked-by: York Sun <yorksun@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Laurentiu TUDOR [Tue, 15 Mar 2011 14:37:36 +0000 (16:37 +0200)]
powerpc/85xx: Fix setting of LIODN prop in PCIe nodes on P3041/P5020
We utilize the compatible string to find the node to add fsl,liodn
property to. However P3041 & P5020 don't have "fsl,p4080-pcie"
compatible for their PCIe controllers as they aren't backwards compatible.
Allow the macro's to specify the PCIe compatible to use to allow SoC
uniqueness. On P3041 & P5020 we utilize "fsl,qoriq-pcie-v2.2" for the
PCIe controllers.
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
projects / u-boot / log