Joe Hershberger [Mon, 21 Dec 2015 22:31:35 +0000 (16:31 -0600)]
net: Fix delay in net_retry test
Introduced in 45b4773 (net/arp: account for ARP delay, avoid duplicate packets on timeout)
Check the arp timeout and adjust the timeout start time before the call
to eth_recv() so that the sandbox driver has the opportunity to adjust
the sandbox timer after the new start time has been recorded.
Also, change the adjustment amount by 11 seconds instead of exactly the
10 seconds that the ping timout is expecting since the timeout check is
looking for the time elapsed to be greater than but not equal to the
specified delay.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 3 Jan 2016 20:50:30 +0000 (13:50 -0700)]
usb: Allow up to 7 storage devices
The current limit of 5 is not enough for the driver model USB tests. Really
we should not have a limit but the driver model code still uses the
usb_dev_desc[] array, which has a limit.
Increasing the limit by 2 should not bother anyone. Adjust it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Marek Vasut <marex@denx.de>
Bin Meng [Tue, 22 Dec 2015 06:43:39 +0000 (22:43 -0800)]
dm: eth: Stick to 'ethact' when 'ethrotate' is 'no' in eth_init()
When 'ethrotate' variable is set to 'no' and 'ethact' variable
is already set to an ethernet device, we should stick to 'ethact'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 22 Dec 2015 06:43:38 +0000 (22:43 -0800)]
dm: eth: Test 'ethrotate' before changing current ethernet device
In eth_current_changed(), the call to eth_get_dev() below has a side
effect of rotating ethernet device if uc_priv->current == NULL. This
is not what we want when 'ethrotate' variable is 'no'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Heiko Schocher [Wed, 25 Nov 2015 08:46:19 +0000 (09:46 +0100)]
powerpc, mpc5xxx: fix missing bootflag init
since:
commit: f05ad9ba "Add a way to skip relocation"
tqm5200s board fails to boot. Reason is that
board_init_f has a function parameter bootflag,
which is not setup in
in arch/powerpc/cpu/mpc5xxx/start.S _start
So board_init_f gets a undefined bootflag,
currently the gd pointer address. Unfortunately
this address sets the GD_FLG_SKIP_RELOC bit,
so u-boot code gets not relocated and u-boot
does not boot ...
Init bootflag with 0, and tqm5200 boots fine again.
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <yorksun@freescale.com>
Peng Fan [Wed, 23 Dec 2015 04:08:09 +0000 (12:08 +0800)]
common: nvedit: use snprintf instead of sprintf
Use snprintf to replace sprintf.
Coverity log:
"
Unbounded source buffer (STRING_SIZE)
string_size: Passing string init_val of unknown size to sprintf.
"
Reported-by: Coverity Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Peng Fan [Wed, 23 Dec 2015 04:07:24 +0000 (12:07 +0800)]
common: env: initialize scalar variable
Before calling hsearch_r, initialize callback entry to NULL.
Coverity log:
"
Uninitialized scalar variable (UNINIT)
uninit_use_in_call: Using uninitialized value e.
Field e.callback is uninitialized when calling hsearch_r.
"
Reported-by: Coverity Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org>
Eric Nelson [Mon, 7 Dec 2015 14:50:01 +0000 (07:50 -0700)]
mmc: update MMC_ERASE argument to match Linux kernel.
Table 41 of the JEDEC standard for eMMC says that bit 31 of
the command argument is obsolete when issuing the ERASE
command (CMD38) on page 115 of this document:
http://www.jedec.org/sites/default/files/docs/jesd84-B45.pdf
The SD Card Association Physical Layer Simplified Specification also
makes no mention of the use of bit 31.
https://www.sdcard.org/downloads/pls/part1_410.pdf
The Linux kernel distinguishes between secure (bit 31 set) and
non-secure erase, and this patch copies the macro names from
include/linux/mmc/core.h.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Eric Nelson <eric@nelint.com> Tested-by: Hector Palacios <hector.palacios@digi.com>
Peng Fan [Tue, 15 Dec 2015 08:27:18 +0000 (16:27 +0800)]
imx: mx6qsabreauto: support lvds display
Move setup_display from board_early_init_f to board_init.
Add more clock settings.
Add blacklight iomux setting.
Add display_info_t info for the lvds screen.
Gong Qianyu [Fri, 18 Dec 2015 09:38:01 +0000 (17:38 +0800)]
i2c: mxc: add a condition in case the parameter is NULL
This could avoid executing the code that only applies to i.MX platforms.
The bus_i2c_init() is called before relocation and will assgin value
to a static variable. If U-Boot is then still running in a flash
device, it's theoretically not allowed to write data to flash without
an erasing operation. For i.MX platforms, the U-Boot is always running
in DDR.
Actually it causes asynchronous error when the ARM64 system error
report is enabled and the flash write protect is set.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Stefano Babic [Fri, 11 Dec 2015 16:30:42 +0000 (17:30 +0100)]
imx_common: check for Serial Downloader in spl_boot_device
Check for bmode before reading the boot device
to check if a serial downloader is started,
and returns UART if the serial downloader is set,
letting SPL to wait for an image if
CONFIG_SPL_YMODEM_SUPPORT is set.
This allows to load again a SPL based board
with imx_usb_loader together with a tool
such as kermit.
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tim Harvey <tharvey@gateworks.com> CC: Fabio Estevam <Fabio.Estevam@freescale.com> CC: Eric Nelson <eric.nelson@boundarydevices.com> Reviewed-by: Eric Nelson <eric@nelint.com> Tested-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Cc: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
Michael Schanz [Thu, 10 Dec 2015 08:58:35 +0000 (09:58 +0100)]
cgtqmx6eval: fix pad configuration for SPI bus
Use the macro SETUP_IOMUX_PAD(...) rather than imx_iomux_v3_setup_multiple_pads(...) in order to setup
the pin configuration for ECSPI1.
ARRAY_SIZE(pads) provides the wrong size for imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)) in
case of MX6QDL. In the particular case, the content of GPR12 is overwritten and the IPG/AHB/ATB/ATP clocks
are deactivated. Therefore, the connection to the system via JTAG is not possible anymore. Furthermore,
kernel version 3.0.35 hangs during bootprocess in the function etm_init().
Signed-off-by: Michael Schanz <michael.schanz@congatec.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Måns Rullgård [Tue, 8 Dec 2015 15:38:46 +0000 (15:38 +0000)]
net: fec_mxc: unregister mdio bus on probe error
If fecmxc_initialize_multi() fails, it frees but does not unregister
the mdio bus, causing subsequent uses of the "mii" command to crash.
Fix this by adding mdio_unregister() calls where needed.
Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Eric Nelson <eric@nelint.com>
Måns Rullgård [Tue, 8 Dec 2015 15:38:45 +0000 (15:38 +0000)]
net: fec_mxc: configure MDIO hold time
If the host clock frequency is higher than 100 MHz, the MDIO hold
time needs to be increased from its current setting of one cycle in
order to meet the specified minium of 10 ns. Writing an appropriate
value to the HOLDTIME field of the MII_SPEED register achieves this.
Comment copied from Linux kernel.
Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Eric Nelson <eric@nelint.com>
This patch writes the default values for TXTL and RXTL to UARTx_UFCR.
Without this patch some older kernel versions crash as UARTx_UFCR was
not always correctly initialized.
Signed-off-by: Maximilian Schwerin <maximilian.schwerin@tigris.de>
Eric Nelson [Fri, 4 Dec 2015 19:32:48 +0000 (12:32 -0700)]
ARM: imx: fsl_esdhc: fix usage of low 4 bits of sysctl register
The low four bits of the SYSCTL register are reserved on the USDHC
controller on i.MX6 and i.MX7 processors, but are used for clocking
operations on earlier models.
Guard against their usage by hiding the bit mask macros on those
processors.
These bits are used to prevent glitches when changing clocks on
i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7.
>From the i.MX6DQ RM:
To prevent possible glitch on the card clock, clear the
FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS
or DVS in System Control Register) or setting RSTA bit.
Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Hector Palacios <hector.palacios@digi.com>
Stefan Brüns [Tue, 22 Dec 2015 00:21:04 +0000 (01:21 +0100)]
usb: musb: Fix hub port setting for SPLIT transactions
The ifdef'ed Linux kernel code uses the 1 based port number, whereas U-Boot
puts a 0 based port number into the register. The reason the 0 based port
number apparently works can probably be taken from the USB 2.0 spec:
8.4.2.2 Start-Split Transaction Token
... The host must correctly set the port field for single and multiple TT
hub implementations. A single TT hub implementation *may ignore* the port
field.
Actually, as far as I understand, a multi TT hub defaults to single TT
(bAlternateSetting: 0) until switched via SetInterface, so even "port 42"
would work.
The change was verified by hardcoding the port number to a wrong value,
SPLIT transactions kept working (although using a DWC2 instead of MUSB).
Tested hubs are the RPi onboard SMC9514 and an external "05e3:0608
Genesys Logic, Inc. USB-2.0 4-Port HUB". The former is a multi TT hub,
the latter single TT only.
Addendum: Tested on sunxi/MUSB by Hans de Goede
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com>
Stefan Brüns [Tue, 22 Dec 2015 00:21:03 +0000 (01:21 +0100)]
usb: Move determination of TT hub address/port into separate function
Start split and complete split tokens need the hub address and the
downstream port of the first HS hub (device view).
The core of the function was duplicated in both host/ehci_hcd and
musb-new/usb-compat.h.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com>
Thomas Chou [Wed, 23 Dec 2015 13:06:12 +0000 (21:06 +0800)]
altera_qspi: set fail_addr for erase ops
If the erase fails, fail_addr might indicate exactly which block
failed. If fail_addr = MTD_FAIL_ADDR_UNKNOWN, the failure was not
at the device level or was not specific to any particular block.
Thomas Chou [Wed, 23 Dec 2015 02:26:03 +0000 (10:26 +0800)]
altera_qspi: call callback even if the erase failed
Erase is an asynchronous operation. Device drivers are supposed
to call instr->callback() whenever the operation completes, even
if it completes with a failure.
Marek Vasut [Sun, 20 Dec 2015 03:00:44 +0000 (04:00 +0100)]
arm: socfpga: Enable SPL MMC/SPI support only if DM_MMC/SPI is enabled
It is not possible to compile MMC/SPI SPL if the respective DM_MMC/DM_SPI
bits are not enabled. Secure the code with an ifdef to prevent compiler
splat.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Chin Liang See <clsee@altera.com>
Masahiro Yamada [Fri, 18 Dec 2015 05:52:32 +0000 (14:52 +0900)]
ARM: uniphier: allow to run zImage rather than uImage
UniPhier SoC family adopt ARM Multi-platform in Linux since the first
upstreaming. Because CONFIG_ARM_PATCH_PHYS_VIRT is defined, the
kernel image is completely position-independent. There is no reason
to decide the load address on compile time, but it is up to the boot
loader. Now, zImage is handier than uImage, also it allows to skip
the relocation of the kernel image.
Masahiro Yamada [Thu, 17 Dec 2015 09:00:40 +0000 (18:00 +0900)]
ARM: uniphier: support ProXstream2, PH1-LD6b boards in single defconfig
These boards are similar enough to be supported in a single defconfig
file. Distinguish one from another by "DEVICE_TREE" from the command
line. The how-to-build in doc/README.uniphier should be also updated.
Masahiro Yamada [Thu, 17 Dec 2015 09:00:39 +0000 (18:00 +0900)]
ARM: uniphier: merge ph1_ld4_defconfig and ph1_sld8_defconfig
These two are similar enough to be merged into a single
defconfig file. Distinguish one from another by "DEVICE_TREE"
from the command line. The how-to-build in doc/README.uniphier
should be also updated.
Masahiro Yamada [Thu, 17 Dec 2015 09:00:37 +0000 (18:00 +0900)]
ARM: uniphier: set DTB file name to fdt_file environment
When we want to boot Linux with a DTB file downloaded from a TFTP
server or somewhere, we need to know the file name to be downloaded.
Assume the U-Boot configuration is shared among some similar boards.
If they are similar enough, the difference only appears in device
trees. The build procedure would be like this:
- Board A: make foo_common_defconfig && make DEVICE_TREE=foo_board_a
- Board B: make foo_common_defconfig && make DEVICE_TREE=foo_board_b
- Board C: make foo_common_defconfig && make DEVICE_TREE=foo_board_c
In this case, the U-Boot image contains nothing about the DTB file name
it is running with. (CONFIG_DEFAULT_DEVICE_TREE is not helpful for this
purpose because it is painful to change it from "make menuconfig" for
each board.)
This commit allows to lookup the DTB file name based on the compatible
string and set it to "fdt_file" environment. Then "tftpboot $fdt_file"
will download the file we want.
projects / u-boot / log