Stefan Roese [Mon, 22 Sep 2008 14:10:43 +0000 (16:10 +0200)]
ppc4xx: Canyonlands: Remove unnecessary FDT warning upon DTB fixup
Depending on the configuration jumper "SATA SELECT", U-Boot disabled
either one PCIe node or the SATA node in the device tree blob. This
patch removes the unnecessary and even confusing warning, when the node
is not found at all.
Wolfgang Denk [Mon, 22 Sep 2008 20:23:06 +0000 (22:23 +0200)]
Fix DPRAM memory leak when CFG_ALLOC_DPRAM is defined, which
eventually leads to a machine check. This change assures that DPRAM
is allocated only once in that case.
Signed-off-by: Gary Jennejohn <garyj@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
Running mtest command on socrates without specifying
an address range crashes the board. This patch changes
default mtest address range to prevent this behavior.
Currently U-Boot crashes after relocation to RAM.
Changing the CPO value of the DDR SDRAM TIMING_CFG_2
register to READ_LAT + 1 (to the value it was before
conversion of socrates to new DDR code) fixes the
problem.
sh: Add support any page size and empty_zero_page to SH Linux uImage
Old U-Boot supported 4KB page size only. If this version, Linux
kernel can not get command line from U-Boot.
SH Linux kernel can change page size and empty_zero_page.
This patch support this function and fix promlem.
Peter Tyser [Tue, 16 Sep 2008 15:04:47 +0000 (10:04 -0500)]
Support for multiple SGMII/TBI interfaces for TSEC ethernet
Fix TBI PHY accesses to use the proper offset in CPU register space. The
previous code would incorrectly access the TBI PHY by reading/writing to CPU
register space at the same location as would be used to access external PHYs.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Acked-by: Andy Fleming <afleming@freescale.com>
This patch is an attempt to implement autoprobing for the Lime
presence on the bus.
Configure GPCM for Lime CS2 and try to access chip ID registers.
Second read atempt delivers register values if the chip is present.
powerpc: Fix bootm to boot up again with a Ramdisk
Commit 2a1a2cb6 didnt remove the dummy mem reservation in fdt_chosen,
and this stopped Linux from booting with a Ramdisk. This patch fixes
this, by deleting the useless dummy mem reservation.
When booting with a Ramdisk, a fix offset FDT_RAMDISK_OVERHEAD is now
added to of_size, so we dont need anymore a dummy mem reservation.
I measured the value of FDT_RAMDISK_OVERHEAD on a MPC8270 based
system (=0x44 bytes) and rounded it up to 0x80).
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Fri, 27 Jun 2008 19:04:20 +0000 (23:04 +0400)]
fsl_elbc_nand: ecclayout cleanups
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Anton Vorontsov [Fri, 27 Jun 2008 19:04:13 +0000 (23:04 +0400)]
fsl_elbc_nand: implement support for flash-based BBT
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Anton Vorontsov [Fri, 27 Jun 2008 19:04:04 +0000 (23:04 +0400)]
fsl_elbc_nand: fix OOB workability for large page NAND chips
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch prevents linker error on AT91RM9200 boards, if
CONFIG_CMD_I2_TREE is set.
It implements i2c_set_bus_speed and i2c_get_bus_speed as a dummy function.
Andrew Dyer [Fri, 12 Sep 2008 00:20:46 +0000 (02:20 +0200)]
arm920t fix constant error in start.S
Code in cpu/arm920t/start.S will die with a compilation error if
CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for
the ARM sub instruction. Change the code so that each is subtracted
independently to avoid the error.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Magnus Lilja [Fri, 29 Aug 2008 08:36:18 +0000 (10:36 +0200)]
i.MX31: Make the SPI bus and chip select configurable for MC13783
The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.
This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Magnus Lilja [Fri, 29 Aug 2008 08:36:17 +0000 (10:36 +0200)]
i.MX31: Add reset_timer() and modify get_timer_masked().
This patch adds the reset_timer() function (needed by nand_base.c) and
modifies the get_timer_masked() to work in the same way as the omap24xx
function.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Hugo Villeneuve [Sat, 30 Aug 2008 21:06:55 +0000 (17:06 -0400)]
ARM DaVinci: Fix broken HW ECC for large page NAND.
Based on original patch by Bernard Blackham <bernard@largestprime.net>
U-boot's HW ECC support for large page NAND on Davinci is completely
broken. Some kernels, such as the 2.6.10 one supported by
MontaVista for DaVinci, rely upon this broken behaviour as they
share the same code for ECCs. In the existing scheme, error
detection *might* work on large page, but error correction
definitely does not. Small page ECC correction works, but the
format is not compatible with the mainline git kernel.
This patch adds ECC code that matches what is currently in the
Davinci git repository (since NAND support was added in 2.6.24).
This makes the ECC and OOB layout written by u-boot compatible with
Linux for both small page and large page devices and fixes ECC
correction for large page devices.
The old behaviour can be restored by defining the macro
CFG_DAVINCI_BROKEN_ECC, which is undefined by default.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com> Acked-by: Sergey Kubushyn <ksi@koi8.net> Signed-off-by: Scott Wood <scottwood@freescale.com>
Petri Lehtinen [Wed, 10 Sep 2008 06:43:49 +0000 (09:43 +0300)]
autoscr: Fix one-character lines and non-newline terminated scripts
When not using hush, the autoscr command now executes lines that are
only one character long. It also runs the last line of scripts even if
it does not end in a newline.
Signed-off-by: Petri Lehtinen <petri.lehtinen@inoi.fi>
Andrew Klossner [Thu, 21 Aug 2008 14:12:26 +0000 (07:12 -0700)]
Fix printf errors under -DDEBUG
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
projects / u-boot / log