Update the mtd driver name in bootargs for at91-based boards
The name of the atmel nand driver in the kernel changed from at91_nand
to atmel_nand back in June 2008, but the at91-based boards config files
still refer to at91_nand. This patch updates them with the new name
Wolfgang Denk [Sun, 16 Aug 2009 21:40:13 +0000 (23:40 +0200)]
Monahans: avoid floating point calculations
Current code for the Monahans CPU defined OSCR_CLK_FREQ as 3.250 (MHz)
which caused floating point operations to be used. This resulted in
unresolved references to some FP related libgcc functions when using
U-Boot's private libgcc functions.
The cfi_flash.c driver cast the flash buffer size to a uchar in
flash_write_cfibuffer(). On some flash parts, (tested on Numonyx
part PC32F512M29EWH), the buffer size is 1KB. Remove the cast to
uchar to enable buffer sizes to be larger.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds watchdog reset call to allow its invokation during decompression
phase. This control was present on old zlib version and here it is
backported for those relevant routines. This patch is sent as a zlib separate
one beacuse it was not tested due to specific board lack.
zlib patches will be unified just in one when this will be validated through
tests.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
This patch updates zlib to the latest stable version.
Only relevant zlib parts were ported to u-boot tree, as already did for the
current zlib (0.95). New zlib guarantees a faster inflate performances
other then others improvements as explained at www.zlib.net.
It also includes Alessandro Rubini's patches to allow 0 as destination pointer
and to call watchdog reset if required by architecture.
UEC FIXED PHY: Determine fixed-phy port using UEC interface name.
Fixed a misunderstanding in the original implementation, 'devnum' that
was used in the cpu/ppc4xx/4xx_enet.c implementation was NOT the
PHY's SMI address, rather it was the number of the MAC interface on
the CPU. The equivalent of this for uec_phy will be the UEC number
stored in mii_info->dev->name. Usage example is updated for uec.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Assigned a static SMI address to all UECs TBIPA address.
It is set to 0x1F by default and can be overwritten on the board
header file by defining CONFIG_UTBIPAR_INIT_TBIPA. This allows
the CPU to simply "reserve" one SMI address instead of using
a different one for each UEC.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Roy Zang [Mon, 10 Aug 2009 19:48:05 +0000 (03:48 +0800)]
Fix E1000 build warning on AP1000 board
Fix E1000 build warning on AP1000 board
Fix the build warning on AP1000 board:
e1000.c:131: warning: 'e1000_read_eeprom' used but never defined
e1000.c:2012: warning: 'e1000_set_phy_mode' defined but not used
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Sandeep Paulraj [Mon, 10 Aug 2009 16:24:40 +0000 (12:24 -0400)]
ARM: Davinci DM355: Enabling DM9000 on DM355 EVM
Due to recent changes to the NET support on U-boot, DM9000
is no longer detected on the DM355 EVM.
This minor update enables DM9000 on the DM355 EVM.
Tested on the DM355 EVM
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
1. mv88E61xx driver compiler warnings fixed
2. idstr if-else statements changed to switch() construct
and added default case too.
This fixed idstr may be uninitialized warning
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Kumar Gala [Mon, 10 Aug 2009 21:40:55 +0000 (16:40 -0500)]
85xx: Removed BEDBUG support from FSL 85xx boards
For some reason the MPC8544 enabled BEDBUG if PCI was enabled and that
got copied int the MPC8536, MPC8572 and P2020 DS boards. The BEDBUG
support has never been made to work completely on e500/85xx so we
just disable it to save space and match the other FSL 85xx boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ilya Yanok [Mon, 8 Jun 2009 00:12:49 +0000 (04:12 +0400)]
mxc-mmc: sdhc host driver for MX2 and MX3 proccessor
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.
Albin Tonnerre [Fri, 7 Aug 2009 10:37:36 +0000 (12:37 +0200)]
Add driver for the ST M95xxx SPI EEPROM
This chip is used in a number of boards manufactured by Calao-Systems
which should be supported soon. This driver provides the necessary
spi_read and spi_write functions necessary to communicate with the chip.
Josh Boyer [Fri, 7 Aug 2009 17:53:20 +0000 (13:53 -0400)]
Dual-license IBM code contributions
It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards. As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.
IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.
Mike Frysinger [Fri, 24 Jul 2009 21:51:27 +0000 (17:51 -0400)]
env: kill off default_environment_size
The only environment type that uses this variable is spi flash, and that is
only because it is reimplementing the common set_default_env() function.
So fix the spi flash code and kill off the default_environment_size in the
process.
Michael Evans [Mon, 13 Jul 2009 19:13:45 +0000 (20:13 +0100)]
Fix examples for OMAP3 boards...
The attached patch corrects an error in the examples/Makefile which
causes the applications in the examples directory to hang on OMAP3
based boards. The current Makefile sets -Ttext during linking to
0x0c100000 which is outside of addressable SDRAM memory. The script
corrects the existing ifeq...else...endif logic to look at the VENDOR
tag rather than the CPU tag.
The patch affects the following configs: omap3_beagle_config,
omap3_overo_config, omap3_evm_config, omap3_pandora_config,
omap3_zoom1_config and omap3_zoom2_config.
Signed-off-by: Michael Evans <horse_dung@hotmail.com>
Edited commit message. Signed-off-by: Wolfgang Denk <wd@denx.de>
Dirk Behme [Sat, 8 Aug 2009 07:30:23 +0000 (09:30 +0200)]
omap3: use only fixed-size types inside ctrl_structs
replace variable types in ctrl_structs for omap3 by those with
fixed size (u8, u16, u32).
Additional ifndef-protection is needed by examples which do not
compile when including asm/types.h
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Roy Zang [Fri, 31 Jul 2009 05:34:02 +0000 (13:34 +0800)]
Add Intel E1000 PCIE card support
Based on Intel PRO/1000 Network Driver 7.3.20-k2
Add Intel E1000 PCIE card support. The following cards are added:
INTEL_82571EB_COPPER
INTEL_82571EB_FIBER,
INTEL_82571EB_SERDES
INTEL_82571EB_QUAD_COPPER
INTEL_82571PT_QUAD_COPPER
INTEL_82571EB_QUAD_FIBER
INTEL_82571EB_QUAD_COPPER_LOWPROFILE
INTEL_82571EB_SERDES_DUAL
INTEL_82571EB_SERDES_QUAD
INTEL_82572EI_COPPER
INTEL_82572EI_FIBER
INTEL_82572EI_SERDES
INTEL_82572EI
INTEL_82573E
INTEL_82573E_IAMT
INTEL_82573L
INTEL_82546GB_QUAD_COPPER_KSP3
INTEL_80003ES2LAN_COPPER_DPT
INTEL_80003ES2LAN_SERDES_DPT
INTEL_80003ES2LAN_COPPER_SPT
INTEL_80003ES2LAN_SERDES_SPT
82571EB_COPPER dual ports,
82572EI single port,
82572EI_COPPER single port PCIE cards
and
82545EM_COPPER,
82541GI_LF
pci cards are tested on both P2020 board
and MPC8544DS board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Thu, 16 Jul 2009 01:31:28 +0000 (21:31 -0400)]
net: sync env ethaddr to device enetaddr in eth_init()
In the previous enetaddr refactoring, the assumption with commit 56b555a644
was that the eth layer would handle the env -> device enetaddr syncing.
This was not the case as eth_initialize() is called only once and the sync
occurs there. So make sure the eth_init() function does the env -> device
sync with every network init.
Reported-by: Andrzej Wolski <awolski@poczta.fm> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Robin Getz [Thu, 23 Jul 2009 07:01:03 +0000 (03:01 -0400)]
minor debug cleanups in ./net
Minor ./net cleanups - no functional changes
- change #ifdef DEBUG printf(); #endif to just debug()
- changed __FUNCTION__ to __func__
- got rid of extra whitespace between function and opening brace
- removed unnecessary braces on if statements
gcc dead code elimination should make this functionally/size equivalent
when DEBUG is not defined. (confirmed on Blackfin, with gcc 4.3.3).
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Matthias Ludwig [Tue, 19 May 2009 07:09:31 +0000 (09:09 +0200)]
omap3: embedd gpmc_cs into gpmc config struct
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
For some reason the AT91rm9200 lowlevel init writes to a bunch of
reserved or read-only addresses. All the boards seem to define the
value-to-be-written values as zero ... but they shouldn't actually
be writing *anything* there.
No documented erratum justifies these accesses. It looks like maybe
some pre-release BDI-2000 setup code has been carried along by cargo
cult programming since at least late 2004 (per GIT history).
Here's a patch disabling what seems to be bogosity. Tested on a
csb337; there were no behavioral changes.
Signed-off-by: David Brownell <david-b@pacbell.net>
on RM9200ek Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Stefan Roese [Tue, 28 Jul 2009 13:12:04 +0000 (15:12 +0200)]
ppc4xx: Canyonlands-NAND-boot: Support 2 Crucial 512MByte SODIMM's
Some Canyonlands boards are equipped with different SODIMM's. This is no
problem with the "normal" NOR booting Canyonlands U-Boot, since it
automatically detects the SODIMM's via SPD data and correctly configures
them. But the NAND booting version is different. Here we only have 4k
of image size to completely setup the hardware, including DDR2 setup.
So we need to use a fixed DDR2 setup here. This doesn't work for different
SODIMM's right now.
Currently only this Crucial SODIMM is support:
CT6464AC667.8FB (dual ranked)
Now some boards are shipped with this SODIMM:
CT6464AC667.4FE (single ranked)
This patch now supports both SODIMM's by configuring first for the dual
ranked DIMM. A quick shows, if this module is really installed. If this test
fails, the DDR2 controller is re-configured for the single
ranked SODIMM.
Stefan Roese [Tue, 28 Jul 2009 08:56:03 +0000 (10:56 +0200)]
ppc4xx: amcc: Move "kernel_addr_r" etc to higher locations (> 16MB)
This patch moves the load addresses for kernel, fdt and ramdisk to higher
addresses (>= 16MB). This enables booting of bigger kernel images (e.g.
lockdep enabled).
Stefan Roese [Tue, 28 Jul 2009 08:50:32 +0000 (10:50 +0200)]
ppc4xx: amcc: Set CONFIG_SYS_BOOTMAPSZ to 16MB for big kernels
This patch changes CONFIG_SYS_BOOTMAPSZ from 8MB to 16MB which is the
initial TLB on 40x PPC's in the Linux kernel. With this change even bigger
Linux kernels (> 8MB) can be booted.
This patch also sets CONFIG_SYS_BOOTM_LEN to 16MB (default 8MB) to enable
decompression of bigger images.
83xx, kmeter1, fix: update in the DTS the correct size for the first flash
When updating the "reg" in the "/localbus/flash@f0000000,0" node
size was wrong updated for the first flash, because the total
size was filled in, instead of the right size for it.
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tom Rix [Sun, 28 Jun 2009 17:52:31 +0000 (12:52 -0500)]
OMAP3 Move twl4030 mmc function
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.
twl4030_mmc_config initializes the twl4030 power setting to
the mmc device. Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.
The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format
twl4030_power_<device>_<action>
In this case the suffix is mmc_init so
device : mmc
action : init
Tom Rix [Sun, 28 Jun 2009 17:52:30 +0000 (12:52 -0500)]
OMAP3 Move twl4030 power and led functions
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.
power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.
The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.
The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED
The directory board/omap3/common was removed because power_init_r
was the only function in it.
Wolfgang Denk [Tue, 28 Jul 2009 20:13:52 +0000 (22:13 +0200)]
TQM8xx* boards: set larger SMC Rx buffer len
Commit 2b3f12c2 added support for configurable SMC Rx buffer length on
8xx systems. Enable this feature on TQM8xx* based boards.
This fixes the problem that pasting text in the middle of a line
(i. e. inserting in edit mode) did not work - only the first two
characters got inserted, the rest was lost.
Signed-off-by: unsik Kim <donari75@gmail.com> Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net> Signed-off-by: Wolfgang Denk <wd@denx.de> Tested-by: Wolfgang Denk <wd@denx.de>
Tom Rix [Sun, 28 Jun 2009 17:52:29 +0000 (12:52 -0500)]
TWL4030 Add power reset button
The Zoom2 power reset button is on the top right side of the
main board. Press and hold for about to 8 seconds to completely
reset the board.
Some of the beta boards have a hardware problem that prevents
using this feature. If is difficult to further characterize the
boards that fail. So disable resetting for all beta boards.
The Zoom1 reset button is the red circle on the top right,
front of the board. Press and hold the button for 8 seconds to
completely reset the board.
After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.
The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.
The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER
Tom Rix [Sun, 28 Jun 2009 17:52:27 +0000 (12:52 -0500)]
OMAP I2C Fix the sampling clock.
This problem is seen on Zoom1 and Zoom2 in the startup and
when i2c probe is used
Before :
In: serial
Out: serial
Err: serial
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_pin: I2C_STAT=1000
I2C read: I/O error
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses:timed out in wait_for_bb: I2C_STAT=1000
02 03 04 05 06 07 08 09 0A 0B 0C 0D <snip>
After :
In: serial
Out: serial
Err: serial
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses: 48 49 4A 4B
The addresses are for the twl4030.
The prescalar that converts the function clock to the sampling
clock is hardcoded to 0. The reference manual recommends 7
if the function clock is 96MHz.
Instead of just changing the hardcoded values, the prescalar
is calculated from the value I2C_IP_CLK.
The i2c #defines are in kHz. The speed passed into the
i2c init routine is in Hz. To be consistent, change the
defines to be in Hz.
The timing calculations are based on what is done in the
linux 2.6.30 kernel in drivers/i2c/buses/i2c_omap.c as
apposed to what is done in TRM.
The major variables in the timing caculations are
specified as #defines that can be overriden as required.
This was runtime verified on Zoom1, Zoom2, Beagle and Overo.
The 400kHz and 3.4M cases were verifed on test Zoom1,
Zoom2, Beagle and Overo configurations.
Testing for omap2 will be done in a second step as Nishanth
and Jean-Christophe commented.
Stefan Roese [Mon, 27 Jul 2009 07:13:38 +0000 (09:13 +0200)]
ppc4xx: Fix problem with NOR range assignment in Canyonlands ft_board_setup
This patch fixes the problem, that the current fdt board fixup code only
set's one range, the one for NOR. By this it's overwriting the already
correctly configured values done in __ft_board_setup(). Just remove this
now unneeded NOR fixup and all the ranges are correctly defined.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Felix Radensky <felix@embedded-sol.com>
Stefan Roese [Mon, 27 Jul 2009 05:42:37 +0000 (07:42 +0200)]
ppc4xx: Kilauea: Fix SDRAM init in NAND booting version
DDR2 Auto-calibration needs to be disabled on the NAND booting PPC4xx
targets. Otherwise the configured fixed init values for some DDR2
controller registers (e.g. RQDC) are not initialized at all resulting
in a non working SDRAM.
Stefan Roese [Mon, 27 Jul 2009 08:53:43 +0000 (10:53 +0200)]
ppc4xx: Fix Arches DDR2 initialization
Testing on AMCC Arches with the latest U-Boot version yielded that DDR2
initialization is currently broken. U-Boot hangs upon relocation to SDRAM
or crashes with random traps. This patch fixes this problem. Arches now
uses a different WRDTR and CLKTR default setting than Canyonlands/Glacier.
Paul Gortmaker [Thu, 23 Jul 2009 21:10:55 +0000 (17:10 -0400)]
sbc8349: combine HRCW flash and u-boot image flash
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x. One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.
This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Mon, 27 Jul 2009 07:58:14 +0000 (09:58 +0200)]
Fix include/common.h for boards with CONFIG_STATUS_LED
The reordering of include/common.h by commit fcd3c87e495f3c48 broke
boards with status LED support, resulting in
error: #error Status LED configuration missing
errors. Undo this reordering to avoid this issue.
Less verbose output when loading vxworks 6.x images
Loading vxWorks 5.x images resulted just into 3 or 4 lines of output.
With vxWorks 6.x and the new GCC it emits about 30 lines, which is
far too noisy in my opinion.
Wolfgang Denk [Thu, 23 Jul 2009 22:17:48 +0000 (00:17 +0200)]
Make include/common.h usable by assembler code
Commit 70ebf316 factored out the ROUND() macro into include/common.h,
not realizing that the primary use of this macro on AT91 systems was
in start.S where common.h was not included, and could not be included
because it contains a lot of C code which the assembler doesn't
understand.
This patch wraps such code in common.h in a "#ifndef __ASSEMBLY__"
construct, and then adds an include to cpu/arm926ejs/start.S thus
solving the problem.
Wolfgang Denk [Thu, 23 Jul 2009 11:15:59 +0000 (13:15 +0200)]
Make linking against libgcc configurable
Many (especially ARM) tool chains seem to come with broken or
otherwise unusable (for the purposes of builing U-Boot) run-time
support libraries `libgcc.a'. By using the "USE_PRIVATE_LIBGCC"
setting we allow to use alternative libraries instead.
"USE_PRIVATE_LIBGCC" can either be set as an environment variable in
the shell, or as a command line argument when running "make", i. e.
$ make USE_PRIVATE_LIBGCC=yes
or
$ USE_PRIVATE_LIBGCC=yes
$ export USE_PRIVATE_LIBGCC
$ make
The value of "USE_PRIVATE_LIBGCC" is the name of the directory which
contains the alternative run-time support library `libgcc.a'. The
special value "yes" selects the directory $(OBJTREE)/lib_$(ARCH) .
Note that not all architectures provide an alternative `libgcc.a' in
their lib_$(ARCH) directories - so far, only ARM does.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Stefan Roese <sr@denx.de>
projects / u-boot / log