Sekhar Nori [Thu, 11 May 2017 14:44:22 +0000 (20:14 +0530)]
davinci: omapl138_lcdk: switch to using TI_COMMON_CMD_OPTIONS
Now that we support using TI_COMMON_CMD_OPTIONS,
we dont have to enable a number of commands explicitly
in the defconfig if we enable TI_COMMON_CMD_OPTIONS.
Enable TI_COMMON_CMD_OPTIONS and regenerate the defconfig
using "make savedefconfig".
CMD_GPIO has been kept disabled because there is no GPIO
support (yet) on OMAP-L138 LCDK.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 10 May 2017 19:26:06 +0000 (15:26 -0400)]
net: Disable the format-extra-args warning
We will see warnings such as:
net/eth_common.c:57:61: warning: data argument not used by format string [-Wformat-extra-args]
sprintf(enetvar, index ? "%s%daddr" : "%saddr", base_name, index);
~~~~~~~~ ^
With clang. In this case we do not want to re-write our code to be less
compact as the above is intentional and readable. Add a comment above
the disabling so that it's clear why we want that warning off.
Tom Rini [Wed, 10 May 2017 19:20:15 +0000 (15:20 -0400)]
gpio-uclass.c: Fix comparison of unsigned expression warning
We declare that gpio_base (which is the base for counting gpios, not an
address) is unsigned. Therefore the comparison with >= 0 is always
true. As the desire is to allow for this base number to be 0, we can
just drop this check. Reported by clang-3.8.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 10 May 2017 19:20:14 +0000 (15:20 -0400)]
cmd/led.c: Remove unnecessary check on 'cmd' value
We first check that if argc is less than 2 we return CMD_RET_USAGE. We
then see if argc is greater than 2 and if so call get_led_cmd() to set
'cmd' and otherwise set it to LEDST_COUNT (which will always be positive
as it's an enum with 0 already assigned). Therefore the test on if cmd
is less than 0 will always be false and simply be omitted. Reported by
clang-3.8.
Tom Rini [Wed, 10 May 2017 19:20:13 +0000 (15:20 -0400)]
cmd/io.c: Fix comparison of unsigned expression warning
The function cmd_get_data_size() returns an int and not unsigned. So we
should assign it to an int rather than unsigned so that we can later
compare the return value. Reported by clang-3.8.
Lokesh Vutla [Wed, 10 May 2017 10:49:52 +0000 (16:19 +0530)]
tools/genboardscfg.py: Make 'Supported' as known status
As per MAINTAINERS[1] file description, 'Supported' is
a valid status for a board. But buildman thinks 'Maintained'
is the only valid state and complains about boards with 'Supported'
status. Update buildman to accept 'Supported' as valid state.
Peng Fan [Tue, 9 May 2017 02:32:03 +0000 (10:32 +0800)]
asm-generic: global_data: change timebase_l/h to unsigned int
Change type of timebase_l/h to unsigned int.
>From lib/time.c: ((uint64_t)gd->timebase_h << 32) | gd->timebase_l;
This piece code is based on that timebase_h and timebase_l are
32bits width, so change the type to unsigned int.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Eddie Cai <eddie.cai.linux@gmail.com> Cc: Jagan Teki <jteki@openedev.com> Cc: York Sun <york.sun@nxp.com> Cc: "Robert P. J. Day" <rpjday@crashcourse.ca> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Peng Fan [Tue, 9 May 2017 02:32:02 +0000 (10:32 +0800)]
arm: change tbu/l type to unsigned int
Change tbu/l type to unsigned int.
>From the timer file for arm,
"(((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;" is used,
This piece code is based on tbu/tbl is 32bits, so change the type to
unsigned int.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 9 May 2017 02:14:35 +0000 (22:14 -0400)]
m5253demo: Fix static variable in non-static inline function warning
The function 'spin_wheel' is declared as inline, but not static and thus
we see warnings that 'w' and 'p' are declared static in a non-static
inline function. Correct this by marking spin_wheel as static inline.
Cc: TsiChung Liew <Tsi-Chung.Liew@freescale.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 9 May 2017 02:14:34 +0000 (22:14 -0400)]
common: Only build cli_readline.o for CMDLINE on non-SPL
With gcc-6 and later we may get a warning such as:
.../common/cli_readline.c:20:21: warning: ‘tab_seq’ defined but not used [-Wunused-const-variable=]
static const char tab_seq[] = " "; /* used to expand TABs */
^~~~~~~
.../common/cli_readline.c:19:19: warning: ‘erase_seq’ defined but not used [-Wunused-const-variable=]
static const char erase_seq[] = "\b \b"; /* erase sequence */
^~~~~~~~~
Because in SPL we're normally not doing interactive commands anyhow, so
lets just not compile this at all in SPL. This also means that we need
to correct the logic (and comment) about what the drivers/ddr/fsl/ and
CONFIG_FSL_DDR_INTERACTIVE requires and this will be included in SPL
there.
Tom Rini [Tue, 9 May 2017 02:14:33 +0000 (22:14 -0400)]
net: uli526x: Fix unknown storage size error
The variable netdev_ethtool_ops is not referenced, drop it. However
with gcc-6 or later we fail to even compile as we do not have the
required struct definition in U-Boot.
Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
The variable 'res' may be unused uninitialized if our call to
mv88e61xx_port_read (register read) fails and we goto the error
handling section. In this case we set 'res' to -EIO to indicate why we
failed.
Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Chris Packham <judge.packham@gmail.com> Cc: Kevin Smith <kevin.smith@elecsyscorp.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 9 May 2017 02:14:28 +0000 (22:14 -0400)]
apalis_imx6: Fix unused variable warning
The variable vga_pads is never referenced, drop.
Cc: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Tom Rini [Tue, 9 May 2017 02:14:27 +0000 (22:14 -0400)]
pcm058: Fix unused variable warnings
The variable nfc_pads is only referenced when CONFIG_CMD_NAND is set,
add a gaurd. The variable gpio_pads is never referenced, drop it. The
variable usdhc4_pads are only referenced when we do not have
CONFIG_CMD_NAND set and we are not doing an SPL build, modify the
existing guard.
Tom Rini [Tue, 9 May 2017 02:14:26 +0000 (22:14 -0400)]
gdsys: P1022: Fix unused variable warnings
The variables prg_stage2_prepare, prg_stage2_success and prg_stage_fail
are only referenced when CCDM_SECOND_STAGE is set, move these to be by
the existing guard.
Cc: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 9 May 2017 02:14:25 +0000 (22:14 -0400)]
gw_ventana: Fix unused variable warnings
The variable nfc_pads is only referenced when CONFIG_CMD_NAND is set,
move the existing guard and drop a now redundant comment. The variable
gwproto_gpio_pads is never referenced, remove it.
Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 9 May 2017 02:14:21 +0000 (22:14 -0400)]
ot1200: Fix unused variable warning
The variable pwm_pad is never referenced, drop.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tom Rini [Tue, 9 May 2017 02:14:19 +0000 (22:14 -0400)]
socrates: Fix a misleading indentation warning
With gcc-6 and later we see a warning about the fact that we have a
construct of "if (test);\n\tstatement". Upon reviewing the code, the
intention here is as the compiler suggests, we only want to execute the
indented statement if the test was true.
Cc: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Fri, 5 May 2017 07:29:10 +0000 (12:59 +0530)]
arm: am33xx: Add support for mulitiple PLL input frequencies
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Fri, 5 May 2017 07:29:08 +0000 (12:59 +0530)]
arm: am33xx: Fix MPU opp selection
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:
MPU values for PG 2.0 and later(Package ZCZ and ZCE):
-------------------------------------------------------
| | ZCZ | ZCE |
|-------------------------------------------------------|
| | VDD[V] | ARM [MHz] | VDD[V] | ARM [MHz] |
|-------|----------|------------|----------|------------|
| NITRO | 1.325 | 1000 | NA | NA |
|-------|----------|------------|----------|------------|
| TURBO | 1.26 | 800 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP120 | 1.20 | 720 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP100 | 1.10 | 600 | 1.10 | 600 |
|-------|----------|------------|----------|------------|
| OPP50 | 0.95 | 300 | 0.95 | 300 |
-------------------------------------------------------
There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.
[1] http://www.ti.com/lit/ds/symlink/am3356.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
B, Ravi [Thu, 4 May 2017 10:15:29 +0000 (15:45 +0530)]
common: dfu: ignore reset for spl-dfu
The SPL-DFU feature enable to load and
execute u-boot from RAM over usb from
PC using dfu-util.
Hence dfu-reset should not be issued
when dfu-util -R switch is issued.
Vikas Manocha [Wed, 3 May 2017 23:38:55 +0000 (16:38 -0700)]
armv7m: add MPU configuration support
Cortex-M archs support option memory protection unit (MPU). MPU is used
to set the memory types, attributes, access permissions for different regions,
cache policies of the device.
e.g. using MPU it is possible to configure memory region as device memory
or strongly ordered, memory attributes like execute never, cache policies
like write-back or write-through.
dm: mmc: omap_hsmmc: Add pre-reloc flag to the driver
For platforms that don't use device tree in SPL the only
way to mark this driver as 'required by relocation' is
with the DM_FLAG_PRE_RELOC flag. Add this to ensure that
the driver is bound.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add debug UART functions to permit omap specific ns16550 to
provide an early debug UART. This is mostly in common with
DEBUG_UART_NS16550 except for Mode definition register which
is required for selecting UART mode(16x auto-baud or 13x mode).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
James Balean [Wed, 19 Apr 2017 02:06:35 +0000 (21:06 -0500)]
Add 16-bit single register pin controller support
Enables the pinctrl-single driver to support 16-bit registers. Only
32-bit registers were supported previously. Reduced width registers are
required for some platforms, such as OMAP.
Signed-off-by: James Balean <james@balean.com.au> Cc: Felix Brack <fb@ltec.ch> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Felix Brack <fb@ltec.ch> Tested-by: Felix Brack <fb@ltec.ch> Reviewed-by: Simon Glass <sjg@chromium.org>
B, Ravi [Tue, 18 Apr 2017 11:57:27 +0000 (17:27 +0530)]
boot: fdt: Perform arch_fixup_fdt() on the given device tree for falcon boot
In single stage bootmode or falcon boot mode, the SPL shall update the
device tree that we load with the normal fixups done via
arch_fixup_fdt(), when possible (ie we have enough information in this
restricted environment to be able to do that still). This will include
for example updating them memory nodes.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[trini: Reword commit message]
Philipp Tomsich [Mon, 17 Apr 2017 15:45:13 +0000 (17:45 +0200)]
spl: Makefile: include /config in the (reduced) FDT used by the SPL stage
When OF control is enabled for the SPL stage, nodes are removed from
the DTB to reduce its size. While /chosen is kept, /config is removed.
There's no reason why /chosen should be kept over /config (and as we
would like to put properties into /config that control the SPL stage),
we add '/config' to the list of nodes to be retained for the SPL stage.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Simon Glass <sjg@chromium.org>
This adds documentation on the u-boot,spl-payload-offset property
(which overrides CONFIG_SYS_SPI_U_BOOT_OFFS during the SPI loading in
the SPL stage, if present).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Mon, 17 Apr 2017 15:45:11 +0000 (17:45 +0200)]
spl: spi: override CONFIG_SYS_SPI_U_BOOT_OFFS via /config-property
For the RK3399-Q7, we need some flexibility (depending on the feature
set we include in the SPL stage and how large our SPI flash is) in
positioning the SPL payload (i.e. the FIT image containing U-Boot, ATF
and the M0 payload) in our SPI flash.
To avoid having to deal with this through different U-Boot images, we
introduce a the '/config/u-boot,spl-payload-offset' property node
allow it to override the default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 5 Apr 2017 23:53:18 +0000 (17:53 -0600)]
arm: Support cache invalidate
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
Alex Deymo [Sun, 2 Apr 2017 08:49:50 +0000 (01:49 -0700)]
disk: Return the partition number in part_get_info_by_name()
Similar to what blk_get_device_part_str() does, this patch makes
part_get_info_by_name() return the partition number in case of a match.
This is useful when the partition number is needed and not just the
descriptor.
Signed-off-by: Alex Deymo <deymo@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Alex Deymo [Sun, 2 Apr 2017 08:49:47 +0000 (01:49 -0700)]
image: Update include/android_image.h
Update the Android image header format to the latest version published
in AOSP. The original code moved to a new repository, so this patch also
updates the reference to that path.
Signed-off-by: Alex Deymo <deymo@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
usb: gadget: avoid variable name clipping in cb_getvar
Hi,
A kind reminder to look at this patch (already reviewed by Marek and acked by Lukasz), and if possible to put it in the next pull list, or the one after is timing is too short.
Thanks in advance for your time
Best Regards
Nicolas
-----Original Message-----
From: Nicolas LE BAYON
Sent: mardi 25 avril 2017 10:18
To: Nicolas LE BAYON <nicolas.le.bayon@st.com>; u-boot@lists.denx.de; lukma@denx.de; marex@denx.de Cc: nlebayon@gmail.com; Patrice CHOTARD <patrice.chotard@st.com>; Jean-philippe ROMAIN <jean-philippe.romain@st.com>
Subject: [U-Boot][PATCH v7] usb: gadget: avoid variable name clipping in cb_getvar
From: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Instead of using a fixed-size array to store variable name, preferring a dynamic allocation treats correctly all variable name lengths.
Variable names are growing through releases and features. By this way, name clipping is prevented.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Lukasz Majewski <lukma@denx.de>
Tom Rini [Wed, 10 May 2017 21:40:11 +0000 (17:40 -0400)]
Merge git://git.denx.de/u-boot-rockchip
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
Eric Gao [Tue, 2 May 2017 10:23:56 +0000 (18:23 +0800)]
rockchip: dts: Add mipi dsi support for rk3399
Add dts config for mipi display, include vop, mipi controller, panel, backlight
. And Enable rk808 for lcd_3v3 in another patch.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Eric Gao [Tue, 2 May 2017 10:23:55 +0000 (18:23 +0800)]
rockchip: board: evb_rk3399: initialize pwm0 for dispaly backlight
Enable pwm0 for display of rk3399 evb board. The PWM do not have decicated
interrupt number in dts and can not get periph_id by pinctrl framework. So
init them here.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Eric Gao [Tue, 2 May 2017 10:23:54 +0000 (18:23 +0800)]
rockchip: video: vop: Reserve enough space for mipi dispaly
plat->size here is used to reserve frame buffer space befor relocation.
our mipi panel use 24 bitwidth, and vop require 32bit align. So the frame
buffer size should be at least 1920*1200*32/8.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Eric Gao [Tue, 2 May 2017 10:23:49 +0000 (18:23 +0800)]
rockchip: include: grf: Add GRF register declaration for mipi dsi
Add GRF register declaration for mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jacob Chen [Tue, 2 May 2017 06:54:51 +0000 (14:54 +0800)]
power: regulator: rk808: add rk818 support
Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Fri, 28 Apr 2017 16:33:58 +0000 (18:33 +0200)]
rockchip: pinctrl: rk3399: add support for the HDMI I2C pins
To add HDMI support for the RK3399, this commit provides the needed
pinctrl functionality to configure the HDMI I2C pins (used for reading
the screen's EDID).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Fri, 28 Apr 2017 16:33:57 +0000 (18:33 +0200)]
rockchip: clk: rk3399: allow requests for HDMI clocks
This allows requests (via the DTS) for PCLK_HDMI_CTRL/PCLK_VIO_GRF,
which are clock gates in the HDMI output path for the RK3399.
As these are enabled by default (i.e. after reset), we don't implement
any logic to actively open/close these clock gates and simply assume
that their reset-default has not been changed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Fri, 28 Apr 2017 15:31:44 +0000 (17:31 +0200)]
rockchip: ARM64: puma-rk3399: get DRAM size from DMC init
With the RK3399 DRAM controller (DMC) driver providing all the
infrastructure, retrieve the DRAM size from the DMC init in the
board-specific code (instead of hard-coding) for the RK3399-Q7 (Puma).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Fri, 28 Apr 2017 15:11:55 +0000 (17:11 +0200)]
rockchip: clk: rk3399: allow requests for PCLK_EFUSE1024NS
The (non-secure) efuse node in the DTS requests PCLK_EFUSE1024NS.
To allow us to add a efuse-driver (and more importantly, to allow
probes of such a driver to succeed), we need need to accept requests
for PCLK_EFUSE1024NS and return a non-error result.
As PCLK_EFUSE1024NS is enabled by default (i.e. after reset), we don't
implement any logic to manage this clock gate and simply assume that
the reset-default has not been changed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Kever Yang [Mon, 24 Apr 2017 02:27:52 +0000 (10:27 +0800)]
dm: sandbox: pwm: add test for pwm_set_invert()
Add test case for new interface set_invert().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Fix typo in subject and build error in sandbox_pwm_set_invert(): Signed-off-by: Simon Glass <sjg@chromium.org>
projects / u-boot / log