Steven A. Falco [Fri, 15 Aug 2008 19:29:12 +0000 (15:29 -0400)]
Replace enums in ata.h with an include of libata.h
This patch removes some enums from ata.h and replaces them with an
include of libata.h. This way, we eliminate duplicated code, and
prevent errors whereby the different versions could be out of sync.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
TsiChung Liew [Tue, 19 Aug 2008 16:53:39 +0000 (16:53 +0000)]
CFI: Fix AMD Legacy sector protect
New implement sector lock and unlock or softlock commands
do not exist in AMD legacy flash. Thus, causing issue
when erasing AMD legacy flash (such as lv040)
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com> Signed-off-by: Stefan Roese <sr@denx.de>
The rest of the MAINTAINERS file appears to be sorted
almost-alphabetically, but entries for the newly added AVR32 boards were
added somewhat randomly. This patch sorts the list alphabetically again.
Also update my e-mail address. The old one still works, but it may not
work forever.
TsiChung Liew [Wed, 25 Jun 2008 20:48:52 +0000 (15:48 -0500)]
Fix dm9000 receive status and len little endian issue
The received status and len was in little endian
format and caused the ethernet unable to proceed
further. Add __le16_to_cpu() in dm9000_rx_status_8/16/32bit().
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Kumar Gala [Fri, 15 Aug 2008 13:24:32 +0000 (08:24 -0500)]
Clean up usage of icache_disable/dcache_disable
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Aug 2008 13:24:31 +0000 (08:24 -0500)]
Update linux bootm to support ePAPR client interface
The ePAPR spec has some subtle differences from the current device
tree based boot interface to the powerpc linux kernel. The powerpc
linux kernel currently ignores the differences that ePAPR specifies.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Harald Welte [Wed, 9 Jul 2008 14:30:30 +0000 (22:30 +0800)]
Add 'license' command to U-Boot command line
The 'license' command includes the U-Boot license (GPLv2) into the
actual bootloader binary. The license text can be shown interactively
at the U-Boot commandline.
For products where the commandline can actually be accessed by the
end user, this helps to prevent inadvertent GPL violations, since the
GPLv2 license text can no longer be 'forgotten' to be included into
the product.
The 'license' command can be enabled by CONFIG_CMD_LICENSE.
Signed-off-by: Harald Welte <laforge@openmoko.org>
TsiChung Liew [Thu, 7 Aug 2008 00:37:17 +0000 (19:37 -0500)]
Change CFG_ENV_SIZE to CFG_ENV_SECT_SIZE for SPI sector erase
The CFG_ENV_SIZE is not suitable used for SPI flash erase
sector size if CFG_ENV_SIZE is less than CFG_ENV_SECT_SIZE.
Add condition check if CFG_ENV_SIZE is larger than
CFG_ENV_SECT_SIZE, calculate the right number of sectors for
erasing.
TsiChung Liew [Mon, 11 Aug 2008 15:54:25 +0000 (15:54 +0000)]
ColdFire: Multiple fixes for M5282EVB
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Remove non-common flash driver in
board/freescale/m54455evb/flash.c. The non-cfi flash will
use CONFIG_FLASH_CFI_LEGACY to configure the flash
attribute.
Kyungmin Park [Wed, 13 Aug 2008 00:11:02 +0000 (09:11 +0900)]
Fix OneNAND build break
Since page size field is changed from oobblock to writesize. But OneNAND is not updated.
- fix bufferram management at erase operation
This patch includes the NAND/OneNAND state filed too.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Fathi BOUDRA [Wed, 6 Aug 2008 08:06:20 +0000 (10:06 +0200)]
OneNAND: Fill in MTD function pointers for OneNAND.
onenand_print_device_info():
- Now returns a string to be placed in mtd->name,
rather than calling printf.
- Remove verbose parameter as it becomes useless.
Signed-off-by: Fathi Boudra <fabo@debian.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
nand_spl: Support page-aligned read in nand_load, use chipselect
Supporting page-aligned reads doesn't incure any sinificant overhead, just
a small change in the algorithm. Also replace in_8 with readb, since there
is no in_8 on ARM.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Mon, 30 Jun 2008 19:13:28 +0000 (14:13 -0500)]
NAND boot: MPC8313ERDB support
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND: Do not write or read a whole block if it is larger than the environment
Environment can be smaller than NAND block size, do not need to read a whole
block and minimum for writing is one page. Also remove an unused variable.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
Ilya Yanok [Mon, 30 Jun 2008 13:34:40 +0000 (15:34 +0200)]
NAND: Scan bad blocks lazily.
Rather than scanning on boot, scan upon the first attempt to check the
badness of a block. This speeds up boot when not using NAND, and reduces
the likelihood of needing to reflash via JTAG if NAND becomes
nonfunctional.
Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Thu, 22 May 2008 20:02:46 +0000 (15:02 -0500)]
fsl_elbc_nand: Hard-code the FBAR/FPAR split.
The hardware has separate registers for block and page-within-block,
but the division between the two has no apparent relation to the
actual erase block size of the NAND chip.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Fri, 21 Mar 2008 21:12:51 +0000 (16:12 -0500)]
Freescale eLBC FCM NAND driver
This is a driver for the Flash Control Machine of the enhanched Local Bus
Controller found on some Freescale chips (such as the mpc8313 and the
mpc8379).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Tue, 18 Mar 2008 20:29:14 +0000 (15:29 -0500)]
Don't panic if a controller driver does ecc its own way.
Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.
The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Sergey Kubushyn [Wed, 9 Jan 2008 14:36:20 +0000 (15:36 +0100)]
NAND: Davinci driver updates
Here comes a trivial patch to cpu/arm926ejs/davinci/nand.c. Unfortunately I
don't have hardware handy so I can not test it at the moment but changes are
rather trivial so it should work. It would be nice if somebody with a
hardware checked it anyways.
Stefan Roese [Sat, 5 Jan 2008 15:49:37 +0000 (16:49 +0100)]
NAND: Update nand_spl driver to match updated nand subsystem
This patch changes the NAND booting driver nand_spl/nand_boot.c to match
the new infrastructure from the updated NAND subsystem. This NAND
subsystem was recently synced again with the Linux 2.6.22 MTD/NAND
subsystem.
Stefan Roese [Sat, 5 Jan 2008 15:47:58 +0000 (16:47 +0100)]
NAND: Update 4xx NDFC driver to match updated nand subsystem
This patch changes the 4xx NAND driver ndfc.c to match the new
infrastructure from the updated NAND subsystem. This NAND
subsystem was recently synced again with the Linux 2.6.22 MTD/NAND
subsystem.
Stefan Roese [Sat, 5 Jan 2008 15:43:25 +0000 (16:43 +0100)]
NAND: Change nand_wait_ready() to not call nand_wait()
This patch changes nand_wait_ready() to not just call nand_wait(),
since this will send a new command to the NAND chip. We just want to
wait for the chip to become ready here.
William Juul [Thu, 15 Nov 2007 10:13:05 +0000 (11:13 +0100)]
YAFFS2 import
Direct import of yaffs as a tarball as of 20071113 from their public
CVS-web at http://www.aleph1.co.uk/cgi-bin/viewcvs.cgi/yaffs2/
The code can also be imported on the command line with:
export CVSROOT=:pserver:anonymous@cvs.aleph1.co.uk:/home/aleph1/cvs cvs logon
(Hit return when asked for a password)
cvs checkout yaffs2
Signed-off-by: William Juul <william.juul@tandberg.com> Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
William Juul [Wed, 31 Oct 2007 12:53:06 +0000 (13:53 +0100)]
Update MTD to that of Linux 2.6.22.1
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com> Signed-off-by: Stig Olsen <stig.olsen@tandberg.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
projects / u-boot / log