Wilson Lee [Fri, 3 Nov 2017 06:39:51 +0000 (23:39 -0700)]
serial: nulldev: Implement "pending" function to fix tstc return "true"
In U-boot, serial_tstc was use to determine is there have a character in
serial console that pending for read. If there is no "pending" function
implemented in serial driver, the serial-uclass will return "true(1)"
to indicate there have a character pending to read.
Thus, read a character from nulldev serial will result in continuous
getting -EAGAIN return which might lead system to hang.
This commit is to fix a bug in nulldev serial which implement "pending"
function in nulldev serial to always indicate there is no character in
console that pending for read.
Signed-off-by: Wilson Lee <wilson.lee@ni.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Keng Soon Cheah <keng.soon.cheah@ni.com> Cc: Chen Yee Chew <chen.yee.chew@ni.com> Cc: Bin Meng <bmeng.cn@gmail.com>
Stephen Warren [Fri, 3 Nov 2017 00:11:27 +0000 (18:11 -0600)]
arm64: support running at addr other than linked to
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Fri, 27 Oct 2017 17:04:08 +0000 (11:04 -0600)]
test/py: add timestamps to log
It can be useful to record how long tests take; this can help debug slow
running test systems or track changes in performance over time. Enhance
the test system to record timestamps while running test:
- Whenever a new log file section is started.
- After U-Boot is started and communication has been established.
- After each host or U-Boot command is executed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Patrice Chotard [Thu, 26 Oct 2017 11:23:19 +0000 (13:23 +0200)]
clk: clk_stm32f7: fix PLL clock division factor
Fix clock division factor initialization for RCC_PLLCFGR
registers.
PLLR bits (bit 31-28) in RCC_PLLCFGR must not be cleared,
it's a forbidden value. So update RCC_PLLCFGR using
clrsetbits_le32() to set only necessary bits fields.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Update arm_pl180_mmci_init() prototype by adding struct mmc**
param. This is needed before converting this driver to driver model
in order to use arm_pl180_mmci_init() in driver model and in none
driver model implementation
Masahiro Yamada [Tue, 17 Oct 2017 13:30:20 +0000 (22:30 +0900)]
lib: libfdt: wrap scripts/dtc/libfdt/* where possible
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
Make them a wrapper of scripts/dtc/libfdt/*. This is exactly what
Linux does to sync libfdt. In order to make is possible, import
<linux/libfdt.h> and <linux/libfdt_env.h> from Linux 4.14-rc5.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
The fdt_region.c is U-Boot own file.
I did not touch them in order to avoid unpredictable impact.
Masahiro Yamada [Tue, 17 Oct 2017 13:30:18 +0000 (22:30 +0900)]
tools: use files from scripts/dtc/libfdt where possible
Prior to this commit, tools/Makefile pulls all libfdt files from
lib/libfdt.
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
This commit changes them to #include ones from scripts/dtc/libfdt.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
I did not touch them in order to avoid unpredictable impact.
The fdt_region.c is U-Boot own file. This is also borrowed from
lib/libfdt/.
Masahiro Yamada [Tue, 17 Oct 2017 04:42:44 +0000 (13:42 +0900)]
pylibfdt: compile pylibfdt only when dtoc/binman is necessary
Currently, pylibfdt is always compiled if swig is installed on your
machine. It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.
"checkbinman" and "checkdtoc" are wrong. It is odd that the final
build stage checks if we have built necessary tools. If your platform
depends on dtoc/binman, you must be able to build pylibfdt. If swig
is not installed, it should fail immediately.
I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be
property select:ed by platforms that need them. Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 17 Oct 2017 04:42:43 +0000 (13:42 +0900)]
pylibfdt: move pylibfdt to scripts/dtc/pylibfdt and refactor makefile
The pylibfdt is used by dtoc (and, indirectly by binman), but there
is no reason why it must be generated in the tools/ directory.
Recently, U-Boot switched over to the bundled DTC, and the directory
structure under scripts/dtc/ now mirrors the upstream DTC project.
So, scripts/dtc/pylibfdt is the best location.
I also rewrote the Makefile in a cleaner Kbuild style.
The scripts from the upstream have been moved as follows:
Keerthy [Thu, 12 Oct 2017 04:48:45 +0000 (10:18 +0530)]
board: ti: dra71x-evm: Hook LDO1 of LP8733 to EN_PIN
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.
Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Felix Brack [Wed, 11 Oct 2017 16:42:23 +0000 (18:42 +0200)]
am33xx: Add a function to query MPU voltage in uV
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Jon Nettleton [Mon, 13 Nov 2017 05:04:30 +0000 (07:04 +0200)]
arm: mvebu: clearfog: Fix SPI-NOR flash access
The production variant of the SPI flash used by the clearfog
devices are based on winbond chips. Additionally enable
SPI_FLASH_BAR since some variants will have 16MB of flash
that requires this to be enabled.
Remove the default speed and mode; these values are taken from the
device tree when CONFIG_DM_SPI_FLASH is enabled.
Add default bus, so that 'sf' detects the SPI flash by default.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: remove speed/mode; add bus; move winbond to defconfig] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
Jon Nettleton [Mon, 6 Nov 2017 08:33:21 +0000 (10:33 +0200)]
arm: mvebu: clearfog: enable XHCI USB
Enable the driver by default for the clearfog boards since the external
port is configured for XHCI.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: split from the SoC setup patch] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
Jon Nettleton [Mon, 6 Nov 2017 08:33:20 +0000 (10:33 +0200)]
arm: mvebu: Add board_setup for xhci hardware
This fixes the USB 3.0 support for the a38x SOC.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
Jon Nettleton [Mon, 6 Nov 2017 08:33:19 +0000 (10:33 +0200)]
mvebu: usb: xhci: a38x support
This makes the initial changes need to support the
a38x series of SOCs. It adds the device-tree identifier
as well as changing the board_support function to take
the IO address designated by device-tree.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t; update 37xx and 8K implementations] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
Ashish Kumar [Mon, 6 Nov 2017 07:49:28 +0000 (13:19 +0530)]
armv8: ls1088ardb: Add distro boot support
Distro boot support gives flexibility to run distro RFS like Ubuntu
being deployed from SD card or SATA drive. If it fails to detect
external storage, fall back to qspi/sd boot.
Enable this by default in RDB's defconfig by selecting
CONFIG_DISTRO_DEFAULTS
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Zhang Ying <zhangying@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Kurt Kanzenbach [Fri, 20 Oct 2017 09:44:25 +0000 (11:44 +0200)]
mtd: nand: fsl-ifc: fix support of multiple NAND devices
Currently the chipselect used to identify the corresponding NAND chip
is stored at the controller and only set during fsl_ifc_chip_init().
This way, only the last NAND chip is working, as the previous value
of cs_nand gets overwritten.
In order to solve this issue the chipselect is computed on demand by
evaluating the bank variable. Thus, the correct chipselect for each
NAND chip operation is used.
Tested on hardware with two NAND chips connected to the IFC
controller.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Scott Wood <oss@buserror.net>
[YS: reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
After adding the "mdelay(500);"
line that was lost in the path the error is gone.
Signed-off-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
[Rebased and updated change and commit message] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Fri, 10 Nov 2017 11:48:44 +0000 (17:18 +0530)]
rockchip: configs: vyasa: Update falcon offsets
Update the falcon offsets for args to 16MB and kernel to 17MB
Since the below commit updated U-Boot proper location along
with rockchip boot image offsets
"spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip"
(sha1: 8f4d62b403db45dfa8b1cadb9da9096c79b7df47)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jagan Teki [Fri, 10 Nov 2017 11:48:43 +0000 (17:18 +0530)]
rockchip: doc: Fix U-Boot proper location for falcon
This patch fixed U-Boot proper location has been
missed to update in bewlo commit
"rockchip: doc: update U-Boot location info"
(sha1: 73e6dbe855f357a8330cfd53ff3033303611c1ad)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The U-Boot location has been moved to block 16384.
This is 8MB, not 4MB.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Fabio Estevam [Fri, 3 Nov 2017 15:40:10 +0000 (13:40 -0200)]
mx51: Select the ESDHC_A001 erratum
When a high speed card is connected to mx51evk the following error is seen:
U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
CPU: Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.
Successfully tested with a high speed SD card on a mx51evk board.
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
No arch specific invalidate_icache_all available!
MMC: FSL_SDHC: 0
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
, which prevents any usage of the SD card.
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
Successfully tested with a high speed SD card on a mx25pdk board.
Fabio Estevam [Fri, 3 Nov 2017 15:40:08 +0000 (13:40 -0200)]
mx25: Move MX25 selection to Kconfig
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Kever Yang [Thu, 2 Nov 2017 07:16:36 +0000 (15:16 +0800)]
rockchip: remove SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR from defconfig
Use default value 0x4000 for SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR instead
of define a new one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 2 Nov 2017 07:16:35 +0000 (15:16 +0800)]
rockchip: doc: update U-Boot location info
Update rockchip U-Boot location to 0x4000/16384.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 2 Nov 2017 07:16:34 +0000 (15:16 +0800)]
spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip
Rockchip use a 'loader2' partition for U-Boot, so u-boot.bin or
u-boot.itb load by SPL need to locate at0x4000. Detail here:
http://opensource.rock-chips.com/wiki_Boot_option
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Klaus Goger [Mon, 6 Nov 2017 22:02:56 +0000 (23:02 +0100)]
rockchip: board: puma_rk3399: make env location selectable via Kconfig
The environment storage location is selectable via Kconfig. We support
eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store
the environment in the SPI-NOR additional to the default eMMC location.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 6 Nov 2017 22:02:53 +0000 (23:02 +0100)]
rockchip: dts: rk3399-puma: update USB configuration
This change updates the USB configuration for the RK3399-Q7 in the DTS:
* fixes the OTG board configuration by enabling it ('okay')
* improves the speed of 'usb start' by disabling the unused EHCI/OHCI
controllers
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
* the GPIO polarity is GPIO_ACTIVE_LOW
* should be set to inactive (enable-active-low) when boot-on settings
are applied
* it can be changed at runtime (i.e. remove the always-on)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Philipp Tomsich [Mon, 6 Nov 2017 22:02:51 +0000 (23:02 +0100)]
rockchip: dts: rk3399-puma: fix the modelling of BIOS_DISABLE
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.
This fixes the mix-up and models it correctly:
* the GPIO is low-active
* the regulator should be enabled (enable-active-high) during
boot-on initialisation
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Kever Yang [Tue, 31 Oct 2017 07:52:20 +0000 (15:52 +0800)]
rockchip: config: use common CONFIG_ENV_SIZE for all SoCs
All Rockchip SoCs use 32KB as CONFIG_ENV_SIZE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 31 Oct 2017 07:52:19 +0000 (15:52 +0800)]
rockchip: config: sync the ENV offset from rockchip legacy U-Boot
Using the ENV offset from rockchip legacy U-Boot for all SoCs,
the offset is 4MB-32KB
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Fri, 3 Nov 2017 08:11:04 +0000 (16:11 +0800)]
rockchip: rock: remove CONFIG_ENV_OFFSET
We use the same default ENV setting in rockchip_common.h for all SoC.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jan Kundrát [Fri, 3 Nov 2017 02:06:35 +0000 (03:06 +0100)]
Do not attempt to use the systemwide libfdt
U-Boot bundles a patched copy of libfdt, so it's wrong to attempt to
include it <like/this>. This breaks the build for me when I have dtc
fully installed in my host -- as happened earlier tonight with
Buildroot, for example.
There are several other occurrences throughout the code where '<libfdt'
matches. I'm not modifying these because I have no clue why the
<systemwide> include style is being used -- IMHO wrongly.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Shawn Guo [Thu, 2 Nov 2017 08:46:34 +0000 (16:46 +0800)]
disk: part_dos: fix part_get_info_extended() function
The check in part_get_info_extended() for a successful partition
searching misses a condition for extended partition. In case of
(ext_part_sector == 0), we should anyway mark the partition as found,
even if it's an extended partition, i.e. (is_extended(pt->sys_ind) == 0).
Otherwise, the extended partition (type 0x0f) will never be identified,
and the following recursive call to part_get_info_extended() will get a
wrong 'part_num' and 'which_part' parameter. In the end, all those
partitions in extended table will not be identified.
Let's add the missing OR condition of (ext_part_sector == 0) for
is_extended() check to fix the problem.
The issue is discovered by running fastboot flash to an extended
partition on eMMC.
Lukasz Majewski [Fri, 27 Oct 2017 10:28:10 +0000 (12:28 +0200)]
gpt: Use cache aligned buffers for gpt_h and gpt_e
Before this patch one could receive following errors when executing
"gpt write" command on machine with cache enabled:
display5 factory > gpt write mmc ${mmcdev} ${partitions}
Writing GPT:
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
success!
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
projects / u-boot / log