Marcel Ziswiler [Thu, 18 Oct 2007 22:25:33 +0000 (00:25 +0200)]
fix pxa255_idp board
The pxa255_idp being an old unmaintained board showed several issues:
1. CONFIG_INIT_CRITICAL was still defined.
2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined.
3. Symbol flash_addr was undeclared.
4. The boards lowlevel_init function was still called memsetup.
5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000.
6. Using -march=armv5 instead of -march=armv5te resulted in lots of
'target CPU does not support interworking' warnings on recent compilers.
7. The PXA's serial driver redefined FFUART, BTUART and STUART used as
indexes rather than the register definitions from the pxa-regs header
file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to
avoid any ambiguities.
8. There were several redefinition warnings concerning ICMR, OSMR3,
OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file.
9. The board configuration file was rather outdated.
10. The part header file defined the vendor, product and revision arrays
as unsigned chars instead of just chars in the block_dev_desc_t
structure.
Vlad Lungu [Thu, 4 Oct 2007 17:47:10 +0000 (20:47 +0300)]
Fix NE2000 driver:
Fixed typo in ne2000.h, thinko re n2k_inb() usage, don't try
to do anything in eth_stop() if eth_init() was not called.
Simplified RX path in order to avoid timeouts on really really
fast NE2000 cards (read: qemu with internal tftp), NetLoop() is
clever enough to cope with 1 packet per eth_rx().
Jon Loeliger [Mon, 27 Aug 2007 17:41:03 +0000 (12:41 -0500)]
86xx: Allow for fewer DDR slots per memory controller.
As a direct correlation exists between DDR DIMM slots
and SPD EEPROM addresses used to configure them, use
the individually defined SPD_EEPROM_ADDRESS* values to
determine if a DDR DIMM slot should have its SPD
configuration read or not.
Effectively, this now allows for 1 or 2 DIMM slots
per memory controller.
Rodolfo Giometti [Mon, 15 Oct 2007 09:59:17 +0000 (11:59 +0200)]
PXA USB OHCI: "usb stop" implementation.
Some USB keys need to be switched off before loading the kernel
otherwise they can remain in an undefined status which prevents them
to be correctly recognized by the kernel.
Stefan Roese [Mon, 15 Oct 2007 09:39:00 +0000 (11:39 +0200)]
ppc4xx: Fix bug in I2C bootstrap values for Sequoia/Rainier
The I2C bootstrap values that can be setup via the "bootstrap" command,
were setup incorrect regarding the generation of the internal sync PCI
clock. The values for PLB clock == 133MHz were slighly incorrect and the
values for PLB clock == 166MHz were totally incorrect. This could
lead to a hangup upon booting while PCI configuration scan.
This patch fixes this issue and configures valid PCI divisor values
for the sync PCI clock, with respect to the provided external async
PCI frequency.
Here the values of the formula in the chapter 14.2 "PCI clocking"
from the 440EPx users manual:
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.
This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.
Martin Krause [Thu, 27 Sep 2007 12:54:36 +0000 (14:54 +0200)]
TQM866M: fix SDRAM refresh
At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 97. This result
in a refresh rate of 4 * 7.8 us at the default clock
50 MHz. At 133 MHz the value will be then 4 * 2.9 us.
This is a compromise until a new method is found to
adjust the refresh rate.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
CFG_MEMTEST_START uses weird magic involving gd, which fails to
compile. Use hardcoded values instead (we actually know how much RAM
we have on board.)
Timo Ketola [Mon, 24 Sep 2007 11:50:32 +0000 (14:50 +0300)]
Bugfix: Use only one PTD for one endpoint
Original isp116x-hcd code prepared multiple PTDs for longer than 16
byte transfers for one endpoint. That is unnecessary because the
ISP116x is able to split long data from one PTD into multiple
transactions based on the buffer size of the endpoint. It also caused
serious problems if the endpoint NAKed some of the transactions. In
that case ISP116x wouldn't notice that the other PTDs were for the same
endpoint and would try the other PTDs possibly out of order. That would
break the whole transfer.
This patch makes isp116x_submit_job to use one PTD for one transfer.
Signed-off-by: Timo Ketola <timo.ketola@exertus.fi> Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Grant Likely [Tue, 25 Sep 2007 21:48:05 +0000 (15:48 -0600)]
Fpga: fix incorrect test of CFG_FPGA_XILINX macro
CFG_FPGA_XILINX is a bit value used to test against the value in
CONFIG_FPGA. Testing for a value will always return TRUE. I don't
think that is the intention in this code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Tue, 18 Sep 2007 18:24:57 +0000 (12:24 -0600)]
Bugfix: remove embedded null (\0) from CFG_BOOTFILE macro in TQM8540_config
/bin/bash and /bin/dash (which /bin/sh is linked to on ubuntu) handle embedded
nulls in a string differently. For example, the following statement:
echo "this is a string\0" > afile
Will produce the following with /bin/bash:
"this is a string\0"
But with /bin/dash, will produce:
"this is a string
Bug fixed by moving the embedded null out of the makefile and into the
config header. Also renamed the macro to avoid usage colision with the same
macro used by other board ports.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Wolfgang Denk [Tue, 18 Sep 2007 15:40:27 +0000 (17:40 +0200)]
MCC200: fix build warning
The MCC200 board config file includes version.h for some customer-
specific setting, which causes warnings with "make depend"; build
version.h before depend.
Updates to atstk1002 U-Boot header file:
- Changed bootargs:
* Set the bootargs for at1002 to point to the SD-card partition instead
* ... of the boot flash.
* Removing the rootfstype since that argument are not needed.
This patch applies some clarifying comments to how the different
clocks are setup according to atstk1002.h Some of the previous
comments where stating wrongful information.
Wolfgang Denk [Sun, 16 Sep 2007 15:10:04 +0000 (17:10 +0200)]
TQM8xx[LM]: Fix broken environment alignment.
With recent toolchains, the environment sectors were no longer aligned to
sector boundaries. The reason was a combination of two bugs:
1) common/environment.c assumed that CONFIG_TQM8xxL would be defined
for all TQM8xxL and TQM8xxM boards. But "include/common.h", where
this gets defined, is not included here (and cannot be included
without causing lots of problems).
Added a new #define CFG_USE_PPCENV for all boards which really
want to put the environment is a ".ppcenv" section.
2) The linker scripts just include environment.o, silently assuming
that the objects in that file are really in the order in which
they are coded in the C file, i. e. "environment" first, then
"redundand_environment", and "env_size" last. However, current
toolchains (GCC-4.x) reorder the objects, causing the environment
data not to start on a flash sector boundary:
Note: this patch fixes just the first part, and cures the alignment
problem by making sure that "env_size" gets placed correctly. However,
we still have a potential issue because primary and redundant
environment sectors are actually swapped, i. e. we have now:
Fix usage of do_div() in nand erase|read|write process output.
The last patch to nand_util.c introduced do_div() instead of libgcc's
implementation. But do_div() returns the quotient in its first
macro parameter and not as result.
This config option sets the default for the progress information
output behavior that can also be configured through the 'quiet'
environment variable.
The legacy NAND code does not print the current progress info
on the console. So this option is for backward compatibility for
units that are in the field and where setting the quiet variable
is not an option. With CFG_NAND_QUIET set to '1' the console
progress info is turned off. This can still be overwritten
through the environment variable.
projects / u-boot / log