serial: stm32x7: remove useless CONFIG_CLK and OF_CONTROL flag
This driver is currently used by STM32F7 and STM32H7 SoCs.
As CONFIG_CLK and OF_CONTROL flags are set by default for these
2 SoCs, this flag becomes useless in this driver, so remove it.
relocate_code() allocates 32 bytes stack frame but only 16 bytes are
freed before return. it will cause errors to possible previous frames
and doesn't make relocate_code() look like a function.
fix by freeing 32 bytes stack space
Signed-off-by: zijun_hu <zijun_hu@htc.com> Reviewed-by: Simon Glass <sjg@chromium.org>
ARMv8: get new GD address from gd->new_gd directly
the new GD address is calculated via board data BD currently
it require the new GD area locates below BD tightly, so a strict
constraint is imposed on memory layout which maybe make special
platform unpleasant.
fix it by getting new GD address from gd->new_gd directly.
Signed-off-by: zijun_hu <zijun_hu@htc.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 7 Oct 2017 15:27:59 +0000 (11:27 -0400)]
cmd/gpt.c, cmd/nvedit.c, tools/fit_image.c: Rework recent fixes for Coverity
The recent changes to these files did not completely fix the previous
issues, or introduced different (minor) issues. In cmd/gpt.c we need to
dereference str_disk_guid to be sure that malloc worked. In
cmd/nvedit.c we need to be careful that we can also fit in that leading
space when adding to the string. And in tools/fit_image.c we need to
re-work the error handling slightly in fit_import_data() so that we only
call munmap() once. We have two error paths here, one where we have an
fd to close and one where we do not. Adjust labels to match this.
Reported-by: Coverity (CID: 167366, 167367, 167370) Signed-off-by: Tom Rini <trini@konsulko.com>
Andy Shevchenko [Tue, 3 Oct 2017 11:55:08 +0000 (14:55 +0300)]
x86: edison: Bring minimal ACPI support to the board
This board is based on Intel Tangier SoC (Intel Merrifield platform)
and may utilize ACPI powerfulness.
Bring minimum support by appending initial DSDT table for it.
Note, the addresses for generated tables are carefully chosen to avoid
any conflicts with existing shadowed BIOS data. The user have somewhat
like ~31 kB available for compiled ACPI tables that ought to be enough.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Tue, 3 Oct 2017 11:55:07 +0000 (14:55 +0300)]
x86: tangier: Enable ACPI support for Intel Tangier
Intel Tangier SoC is a part of Intel Merrifield platform which doesn't
utilize ACPI by default. Here is an attempt to unleash ACPI flexibility
power on Intel Merrifield based platforms.
The change brings minimum support of the devices that found on
Intel Merrifield based end user device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Wed, 27 Sep 2017 02:14:44 +0000 (22:14 -0400)]
tools/fit_image.c: Update some return code paths
Coverity has found some problems with the return paths in parts of this
code. We have a case where we were going to the wrong part of the
unwind (open() failed so we cannot close the fd), a case where we were
only free()ing our buf on the error path and finally a case where we did
not munmap in the failure path.
Reported-by: Coverity (CID: 138492, 138495, 143064) Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 27 Sep 2017 00:44:32 +0000 (20:44 -0400)]
cmd/pxe.c: Rework initrd and bootargs handling slightly
For the initrd portion of handling our bootm arguments we do not have a
sufficiently long enough buffer for some improbable 64bit cases. Expand
this buffer to allow for a 64bit address and almost 256MB initrd to be
used. Make use of strncpy/strncat when constructing the values here
since we know what the worst case valid values are, length wise.
Similarly for bootargs themselves, we need to make use of strlen/sizeof
and strncpy/strncat to ensure that we don't overflow bootargs itself.
Cc: Simon Glass <sjg@chromium.org> Cc: Alexander Graf <agraf@suse.de> Reported-by: Coverity (CID: 131256) Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 26 Sep 2017 23:37:11 +0000 (19:37 -0400)]
cmd/nvedit.c: Update input handling to cover overflow cases
When we have multiple messages provided, we need to be sure that we do
not exceed the length of our 'message' buffer. In the for loop, make
sure that pos is not larger than message. Only copy in at most however
much of the message buffer remains. Finally, if we have not reached the
end of the message buffer, put in a space and NULL, and if we have,
ensure the buffer is now NULL termined.
Reported-by: Coverity (CID: 165116) Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 26 Sep 2017 18:08:30 +0000 (14:08 -0400)]
test/dm: Fix string handling issues in the eth test
Coverity scan has identified potential buffer overruns in these tests.
Correct this by zeroing our buffer and using strncpy not strcpy.
Reported-by: Coverity (CID: 155462, 155463) Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Tue, 26 Sep 2017 16:43:12 +0000 (12:43 -0400)]
test/overlay: Fix various malloc/free leaks
With the overlay tests now being built in sandbox Coverity has found a
number of issues in the tests. In short, if malloc ever failed we would
leak the previous mallocs, so we need to do the usual goto pattern to
free each in turn. Finally, we always looked at the free()d location to
see how many tests had failed for the return code.
Create a common exit for most of the error handling code in
do_rename_gpt_parts. Delete the list elements in disk_partitions
before calling INIT_LIST_HEAD from get_gpt_info() a second time.
The SIZEOF_MISMATCH error is not addressed, since that problem was
already fixed by "GPT: incomplete initialization in
allocate_disk_part".
Tuomas Tynkkynen [Mon, 25 Sep 2017 19:06:34 +0000 (22:06 +0300)]
fs-test: Add test for a filename using '..' to go back to the root
The previous commit fixed a problem in FAT code where going back to the
root directory using '..' wouldn't work correctly on FAT12 or FAT16.
Add a test to exercise this case (which was once fixed in commit 18a10d46f26 "fat: handle paths that include ../" but reintroduced due to
the directory iterator refactoring).
This test only very barely catches the problem - without the fix the
size command still gives valid output but the additional spurious
"Invalid FAT entry" error message makes it not get caught in the
'egrep -A3 ' output. I tried to make a proper test that grows the root
directory to two clusters lots of with dummy files but that causes the
write tests to crash the sandbox totally...
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Tom Rini <trini@konsulko.com>
Tuomas Tynkkynen [Mon, 25 Sep 2017 19:06:33 +0000 (22:06 +0300)]
fs/fat: Fix pathnames using '..' that lead to the root directory
If we end up back in the root directory via a '..' directory entry, set
itr->is_root accordingly. Failing to do that gives spews like
"Invalid FAT entry" and being unable to access directory entries located
past the first cluster of the root directory.
Fixes: 8eafae209c35 ("fat/fs: convert to directory iterators") Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tuomas Tynkkynen [Mon, 25 Sep 2017 19:06:32 +0000 (22:06 +0300)]
fs-test: Add FAT16 support
Currently we can only test FAT32 which is the default FAT version that
mkfs.vfat creates by default. Instead make it explicitly create either a
FAT16 or a FAT32 volume. This allows us to exercise more code, for
instance the root directory handling is done differently in FAT32 than
the older FATs.
Adding FAT12 support is a much bigger job since the test creates a 2.5GB
file and the FAT12 maximum partition size is way smaller than that.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Tom Rini <trini@konsulko.com>
Tuomas Tynkkynen [Mon, 25 Sep 2017 19:06:31 +0000 (22:06 +0300)]
fs/ext4: Fix group descriptor checksum calculation
The current code doesn't compute the group descriptor checksum correctly
for the filesystems that e2fsprogs 1.43.4 creates (they have
'Group descriptor size: 64' as reported by tune2fs). Extend the checksum
calculation to be done as ext4_group_desc_csum() does in Linux.
This fixes these errors in dmesg from running fs-test.sh and makes it
succeed again:
[1671902.620699] EXT4-fs (loop1): ext4_check_descriptors: Checksum for group 0 failed (35782!=10965)
[1671902.620706] EXT4-fs (loop1): group descriptors corrupted!
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Felix Brack [Fri, 22 Sep 2017 12:27:28 +0000 (14:27 +0200)]
doc: Fix statements on case sensitivity for regulator prefix
The regulator bindings state that regulator prefixes are allowd to be
in upper or lower case. However pmic_bind_children from pmic_uclass uses
strncmp to compare DT node name against prefix. This comparison is case
sensitive hence the regulator driver prefix case matters.
Sam Protsenko [Thu, 21 Sep 2017 22:51:59 +0000 (01:51 +0300)]
omap: Fix warning when looking for userdata part
When eMMC was formattaed for Linux partition table, "userdata" partition
is missing. In this case, part_get_info_by_name() iterates over all
registered drivers (which are PART_TYPE_EFI, PART_TYPE_DOS and
PART_TYPE_ISO). And when it comes to PART_TYPE_ISO (which has empty
partition table), we can see next warning in U-Boot output:
** First descriptor is NOT a primary desc on 1:1 **
This patch switches to part_get_info_by_name_type() API in order to
check only EFI partitions for "userdata" partitions. This eliminates
mentioned warning.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Sam Protsenko [Thu, 21 Sep 2017 22:51:58 +0000 (01:51 +0300)]
disk: Provide API to get partition by name for specific type
There is already existing function part_get_info_by_name().
But sometimes user is particularly interested in looking for only
specific partition type. This patch implements such an API that
provides partition searching by name for specified partition type.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Sam Protsenko [Thu, 21 Sep 2017 20:01:00 +0000 (23:01 +0300)]
omap: Omit fastboot.userdata_size related errors
When using regular $partitions variable (for Linux boot), we can see
some unwanted messages:
> ERROR: cannot find partition: 'userdata'
> at arch/arm/mach-omap2/utils.c:96/omap_mmc_get_part_size()
> Warning: fastboot.userdata_size: unable to calc
Let's remove those, as missing 'userdata' partition is correct behavior
for Linux partition, and we don't want to see some Android-related
messages in this case.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
(Note that the 'highmem=off' parameter to the 'virt' machine is required for
PCI to work in U-Boot.) This command line enables the following:
- u-boot.bin loaded and executing in the emulated flash at address 0x0
- A generated device tree blob placed at the start of RAM
- A freely configurable amount of RAM, described by the DTB
- A PL011 serial port, discoverable via the DTB
- An ARMv7 architected timer
- PSCI for rebooting the system
- A generic ECAM-based PCI host controller, discoverable via the DTB
Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
The following ones are supported by both U-Boot and Linux:
- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
- To add an Intel E1000 network adapter, pass e.g.:
-net nic,model=e1000 -net user
- To add an EHCI-compliant USB host controller, pass e.g.:
-device usb-ehci,id=ehci
- To add a NVMe disk, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tuomas Tynkkynen [Tue, 19 Sep 2017 20:18:06 +0000 (23:18 +0300)]
PCI: Add driver for a 'pci-host-ecam-generic' host controller
QEMU emulates such a device with '-machine virt,highmem=off' on ARM.
The 'highmem=off' part is required for things to work as the PCI code
in U-Boot doesn't seem to support 64-bit BARs.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tuomas Tynkkynen [Tue, 19 Sep 2017 20:18:04 +0000 (23:18 +0300)]
pci: xilinx: Use pci_generic_mmap_{read, write}_config()
Use the new helper function to avoid boilerplate in the driver.
Note that this changes __raw_writel et al. to writel. AFAICT this is
no problem because:
- The Linux driver for the same hardware uses the non-__raw variants as
well (via pci_generic_config_write()).
- This driver seems to be used only on MIPS so far, where the __raw and
non-__raw accessors are the same.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tuomas Tynkkynen [Tue, 19 Sep 2017 20:18:03 +0000 (23:18 +0300)]
pci: Add helper for implementing memory-mapped config space accesses
This sort of pattern for implementing memory-mapped PCI config space
accesses appears in U-Boot twice already, and a third user is coming up.
So add helper functions to avoid code duplication, similar to how Linux
has pci_generic_config_write and pci_generic_config_read.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
spl: dm: Make it possible for the SPL to pick its own DTB from a FIT
u-boot can be embedded within a FIT image with multiple DTBs. It then
selects at run-time which one is best suited for the platform.
Use the same principle here for the SPL: put the DTBs in a FIT image,
compress it (LZO, GZIP, or no compression) and append it at the end of the
SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
[trini: Move default y of SPL_MULTI_DTB_FIT_DYN_ALLOC to it being the
default choice if SYS_MALLOC_F, drop spl.h include from lib/fdtdec.c
it's unused.]
Signed-off-by Tom Rini <trini@konsulko.com>
dts: renamed FIT_EMBED to MULTI_DTB_FIT and moved it to the dts Kconfig
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 4 Oct 2017 20:44:30 +0000 (16:44 -0400)]
common: Drop LOGLEVEL to 4
While this came in with a default value of 6 I am lowering this to 4.
The MTD/UBI code has a large number of error messages that we include
now. In addition, "normally" warning messages are not included so this
feels like a more natural level to have.
Many drivers had started to use dev_err, dev_info, etc. for log
functions. Currently, we are relying on <linux/compat.h>, but I
guess the best home is <dm/device.h>, taking into account that
Linux defines them in <linux/device.h>.
For now, I am leaving the ones in <linux/compat.h> because lots of
Linux-originated code uses dev_*(), but the first argument is not
struct udevice, so we need to ignore the bogus argument. More
efforts are needed to iron out the issues.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
As commit 84b8bf6d5d2a ("bug.h: move BUILD_BUG_* defines to
include/linux/bug.h") noted, include/linux/bug.h was locally
modified for U-Boot because the name conflict of error() caused
build errors at that time.
Now error() is gone, so we can fully sync BUILD_BUG* with Linux.
These macros are just compile-time utilities. Nothing depends on
platform code, so it should make sense to simply copy Linux's ones.
Please note Linux split BUILD_BUG stuff out into <linux/build_bug.h>
by commit bc6245e5efd7. Let's follow it.
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle] Signed-off-by: Tom Rini <trini@konsulko.com>
printk: collect printk stuff into <linux/printk.h> with loglevel support
When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*(). U-Boot does not support them in a clean
way. So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.
We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround. Hence this
patch, to find the best home for all printk variants. If you want to
use printk() and friends, please include <linux/printk.h>. This header
is self-contained, and pulls in only a few headers.
When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards. This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.
To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel". (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.
The difference is the loglevel is build-time determined. To save the
image size, lower priority pr_*() are compiled out. I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.
I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL] Signed-off-by: Tom Rini <trini@konsulko.com>
Maxime Ripard [Wed, 23 Aug 2017 11:31:08 +0000 (13:31 +0200)]
sunxi: usb_phy: invert the USB phy_ctl condition
All the new SoCs from Allwinner since the A33 have had the phy_ctl offset
at 0x410 instead of 0x404 that was used on the previous SoCs.
Instead of adding more and more special cases as the number of SoCs grow,
let's invert the test to have 0x410 by default, and the (hopefully) fixed
number of old SoCs being the exception.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Suggested-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
The upstream (Linux) device tree file for the Bananapi M3 follows the
convention of using the well known brand name, instead of the vendor
name, for naming. The file was recently added to upstream in commit 359b5a1e1c2d ("ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi
BPI-M3")
Rename the device tree file in U-boot to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Wed, 23 Aug 2017 08:12:22 +0000 (10:12 +0200)]
sunxi: Remove the MMC index hack
The current code, if there's both an eMMC and an MMC slot available on the
board, will swap the MMC indices based on whether we booted from the eMMC
or the MMC. This way, the MMC we're supposed to boot on will always have
the index 0.
However, this causes various issues, for example when using other
components that base their behaviour on the MMC index, such as fastboot.
Let's remove that hack, and take the opposite approach. The MMC will always
have the same index, but the bootcmd will pick the same device than the one
we booted from. This is done through the introduction of the mmc_bootdev
environment variable that will be filled by the board code based on the
boot device informations we can get from the SoC.
In order to not introduce regressions, we also need to adjust the fastboot
MMC device and the environment device in order to set it to the eMMC, over
the MMC, like it used to be the case.
Tested-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Wed, 23 Aug 2017 08:08:29 +0000 (10:08 +0200)]
sunxi: Use sunxi_get_boot_device
Our current board code duplicates a bit the sunxi_get_boot_device logic.
Now that we can use that function in the full-flavoured U-Boot, remove that
duplication and call the function instead.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Thu, 24 Aug 2017 09:52:32 +0000 (11:52 +0200)]
cmd: Move CONFIG_RANDOM_UUID to Kconfig
CONFIG_RANDOM_UUID is used by the GPT command to generate random UUID when
none are provided.
Move that option to Kconfig.
Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 5 Sep 2017 18:59:04 +0000 (20:59 +0200)]
sunxi: sina33: Sync the device tree with the kernel
The kernel DT of the SinA33 has evolved quite a bit. Make sure we sync it
and its upstream DTSI to be able to use the OTG. The DTs were taken from
the 4.13 kernel release.
Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Thu, 7 Sep 2017 18:40:42 +0000 (20:40 +0200)]
sunxi: Imply USB_ETHER
Now that we can enable the usb_ether gadget, do it. This will be especially
useful for boards that don't have any ethernet controller, such as the ones
based on the A13 or A33.
Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Thu, 7 Sep 2017 08:29:51 +0000 (10:29 +0200)]
cmd: fastboot: Rework fastboot dependency
Fastboot need a bunch of options to be operating properly, such as the
g_dnl gadget, the fastboot command, and some options that make sense. Since
fastboot is now part of Kconfig, make sure we have them right.
That will also reduce the boilerplate in the defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Thu, 7 Sep 2017 08:46:24 +0000 (10:46 +0200)]
sunxi: imply USB_GADGET
A good number of our boards have USB_GADGET enabled. Imply it so that all
the boards can benefit from it, and remove some boilerplate from our
defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 12 Sep 2017 17:41:15 +0000 (19:41 +0200)]
sunxi: provide default USB gadget setup
All the Allwinner boards use the same manufacturer, VID and PID for the
gadgets. Make them the defaults to remove some boilerplate from our
defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Thu, 7 Sep 2017 06:46:14 +0000 (08:46 +0200)]
usb: gadget: usb_ether: Move the interfaces to Kconfig
We need to select an interface for the usb_ether gadget, and they haven't
been converted to Kconfig yet. Add a choice to make sure we have an option
selected, and convert all the users.
Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Paul Burton [Thu, 14 Sep 2017 22:05:13 +0000 (15:05 -0700)]
sandbox: Use asm-generic/io.h
Convert the sandbox architecture to make use of the new asm-generic/io.h
to provide address mapping functions. As sandbox actually performs
non-identity mapping between physical & virtual addresses we can't
simply make use of the generic mapping functions, but are able to
implement phys_to_virt() & make use of it from map_physmem().
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
projects / u-boot / log