York Sun [Fri, 22 Jul 2016 17:52:23 +0000 (10:52 -0700)]
armv8: fsl-layerscape: mmu: Fix enabling MMU
MMU bit in SCTLR needs to be set explicitly after tables are
created. It isn't an issue for EL3 becuase this bit is already
set by early MMU setup. But for other exception levels this
bit was not set.
ARMv7: PSCI: ls102xa: add more PSCI v1.0 functions implemention
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0,
they are as the list:
psci_version,
psci_features,
psci_cpu_suspend,
psci_affinity_info,
psci_system_reset,
psci_system_off.
Tested on LS1021aQDS, LS1021aTWR.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com> Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds all the PSCI v1.0 functions in to the common framework, with
all the functions returning "not implemented" by default, as a common framework
all the dummy functions are added here, it is up to every platform developer to
decide which version of PSCI and which functions to implement.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
Mingkai Hu [Tue, 5 Jul 2016 08:01:56 +0000 (16:01 +0800)]
drivers: net/fm: Add Fman support for LS1046A
The Fman module on LS1046A is similiar with that on LS1043A but
LS1046A has one more XFI (10GbE) interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Mingkai Hu [Tue, 5 Jul 2016 08:01:55 +0000 (16:01 +0800)]
armv8: fsl_lsch2: Add LS1046A SoC support
The LS1046A processor is built on the QorIQ LS series architecture
combining four ARM A72 processor cores with DPAA 1.0 support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Mihai Bantea <mihai.bantea@freescale.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Qianyu Gong [Tue, 5 Jul 2016 08:01:54 +0000 (16:01 +0800)]
armv8: fsl_lsch2: Add SerDes 2 support
New SoC LS1046A belongs to Freescale Chassis Generation 2 and
has two SerDes so we need to add this support in fsl_lsch2.
The SoC related SerDes 2 support will be added in SoC patch.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Alison Wang [Tue, 5 Jul 2016 08:01:52 +0000 (16:01 +0800)]
armv8: fsl-layerscape: Add A72 core detection
Add support to detect Cortex-A72 core for printing it out.
The Initiator Version of A72 core should be 0x4.
Signed-off-by: Alison Wang <alison.wang@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Tue, 14 Jun 2016 17:52:40 +0000 (13:52 -0400)]
arm: ls1021atwr: Add SD secure boot target
Add SD secure boot target for ls1021atwr.
Implement board specific spl_board_init() to setup CAAM stream ID and
corresponding stream ID in SMMU. Change the u-boot size defined by a
macro for copying the main U-Boot by SPL to also include the u-boot
Secure Boot header size as header is appended to u-boot image. So header
will also be copied from SD to DDR.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Tue, 14 Jun 2016 17:52:39 +0000 (13:52 -0400)]
SECURE_BOOT: Enable SD as a source for bootscript
Add support for reading bootscript and bootscript header from SD. Also
renamed macros *_FLASH to *_DEVICE to represent SD alongwith NAND and
NOR flash.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Tue, 14 Jun 2016 17:52:38 +0000 (13:52 -0400)]
SECURE_BOOT: Enable chain of trust in SPL framework
Override jump_to_image_no_args function to include validation of
u-boot image using spl_validate_uboot before jumping to u-boot image.
Also define macros in SPL framework to enable crypto operations.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
Due to a oversight in testing, the initialization of the recently
introduced Freescale I2C DM driver works only for 36 bit mode of e.g.
the MPC85XX SoCs (specifically, if the physical addresses are 64 bit
wide and the DT addresses 32 bit wide).
This patch corrects the initialization so that it will work in a more
general setting.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: York Sun <york.sun@nxp.com>
Some devices using the MVTWSI driver have the option to run at speeds
faster than Standard Mode (100kHZ). On the Armada 38x controllers, this
is actually necessary, since due to erratum FE-8471889, a timing
violation concerning repeated starts prevents the controller from
working correctly in Standard Mode. One of the workarounds recommended
in the erratum is to set the bus to Fast Mode (400kHZ) operation and
ensure all connected devices are set to Fast Mode.
In the current version of the driver, however, the delay times are
hard-coded to 10ms, corresponding to Standard Mode operation. To take
full advantage of the faster modes, we would need to either keep the
currently configured I2C speed in a globally accessible variable, or
pass it to the necessary functions as a parameter. For DM, the first
option is not a problem, and we can simply keep the speed in the private
data of the driver. For the legacy interface, however, we would need to
introduce a static variable, which would cause problems with boots from
NOR flashes; see commit d6b7757 "i2c: mvtwsi: Eliminate
twsi_control_flags."
As to not clutter the interface with yet another parameter, we therefore
keep the default 10ms delays for the legacy functions.
In DM mode, we make the delay time dependant on the frequency to allow
taking full advantage of faster modes of operation (tested with up to
1MHZ frequency on Armada MV88F6820).
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Zero-length offsets are not properly handled by the driver. When a read
operation with a zero-length offset is started, a START condition is
asserted, and since no offset bytes are transferred, a repeated START is
issued immediately after, which confuses the controller.
To fix this, we send the first START only if any address bytes need to
be sent, and keep track of the expected start status accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
The length of the address parameter of the __twsi_i2c_read and
__twsi_i2c_write functions is fixed to four bytes.
As a final step in the preparation of the DM conversion, we make the
length of this parameter variable by turning it into an array of bytes,
and convert the 32 bit value that's passed to the legacy functions into
a four-byte-array on the fly.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
To be able to use the compatibility layer from the DM functions, we
factor the adap parameter out of all functions, and pass the actual
register base instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Since some additional parameters will be added in the course of this
patch series (especially with the addition of DM support), we replace
the longer "unsigned int" declarations with "uint" declarations to keep
the parameter lists more readable.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
The twsi_stop function contains a parameter "status," which is used to
pass in the current exit status of the function calling twsi_stop, and
either return this status unchanged if it indicates an error, or return
twsi_stop's exit status if it does not indicate an error.
While not massively complicated, this adds another purpose to the
twsi_stop function, which should have the sole purpose of asserting a
STOP condition on the bus (and not manage the exit status of its
caller).
Therefore, we move the exit status management into the caller functions
by introducing a "stop_status" variable and returning either the status
before the twsi_stop call (kept in the "status" variable), or the status
from the twsi_stop call, depending on which indicates an error.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Due to breaking boots from NOR flashes, commit d6b7757 ("i2c: mvtwsi:
Eliminate twsi_control_flags") removed the static global
twsi_control_flags variable, which kept a set of default flags that were
always or'd to the control register when writing. It was replaced with a
flags parameter, which was passed around between the functions that
needed it.
Since the twsi_control_flags variable was used just for the purposes of
a) setting the MVTWSI_CONTROL_TWSIEN on every control register write,
and
b) setting the MVTWSI_CONTROL_ACK from twsi_i2c_read if needed,
anyway, the added overhead of another variable being passed around is no
longer justified, and we are better off implementing this flag setting
logic locally in the functions that actually write to the control
register.
Therefore, this patch sets MVTWSI_CONTROL_TWSIEN on every control
register write, replaces the twsi_i2c_read's flags parameter with a
ack_flag parameter, which tells the function whether to acknowledge the
read or not, and removes every other instance of the flags variable.
This has the added benefit that now every notion of "global default
flags" is gone, and it's much easier to see which control flags are
actually set at which point in time.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
i2c: mvtwsi: Streamline code and add documentation
Convert groups of logically connected preprocessor defines into proper
enums, one macro into an inline function, and add documentation
to/extend existing documentation of these items.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Mugunthan V N [Mon, 18 Jul 2016 09:41:02 +0000 (15:11 +0530)]
defconfig: am335x_boneblack_vboot: enable i2c driver model
Enable i2c driver model for am335x_boneblack_vboot as omap i2c
supports driver model. Also enable CONFIG_DM_I2C_COMPAT for
legacy drivers of i2c devices.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
John Keeping [Fri, 15 Jul 2016 16:33:23 +0000 (17:33 +0100)]
rockchip: sdram: Fix register layout for Linux
The ChromeOS kernel reads the RAM settings from PMU_SYS_REG2 and expects
the bootloader to store the necessary information there. We're using
the same register to pass the same information between the SPL and
U-Boot but in a slightly different format.
Change this to use the format expected by the Linux DMC driver so that
the system doesn't hang in Linux by misconfiguring the RAM.
This is almost the same as commit b5788dc ("rockchip: rk3288: correct
sdram setting") which was reverted in commit b525556 ("Revert "rockchip:
rk3288: correct sdram setting"") but parenthese have been added to apply
the mask correctly when reading the "bw" setting and a couple of minor
style issues have been fixed to keep check_patch.pl happy.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Mon, 18 Jul 2016 09:00:58 +0000 (17:00 +0800)]
mmc: rockchip: add SDHCI driver support for rockchip soc
Rockchip rk3399 using arasan sdhci-5.1 controller.
This patch add the controller support to enable mmc device
with full driver-model support, tested on rk3399 evb board.
According to my test result, this driver should be OK,
the command "part list mmc 0" can result in a right output,
but all the mmc command failed like this:
=> mmc info
No MMC device available
Command failed, result=1
The result of get_mmc_num in cmd/mmc.c is always 0?
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Tue, 19 Jul 2016 13:16:59 +0000 (21:16 +0800)]
ARM64: rockchip: add support for rk3399 SoC based evb
RK3399 is a SoC from Rockchip with dual-core Cortex-A72
and quad-core Cortex-A53 CPU. It supports two USB3.0
type-C ports and two USB2.0 EHCI ports. Other interfaces
are very much like RK3288, the DRAM are 32bit width address
and support address from 0 to 4GB-128MB range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Tue, 19 Jul 2016 13:16:58 +0000 (21:16 +0800)]
dts: add support for Rockchip rk3399 soc
These files are from kernel upstream:
"649a371 Add linux-next specific files for 20160616"
with some modification need by U-Boot:
- chosen with stdout-path to uart2.
- add clock-frequency for uart2
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 17 Jul 2016 21:23:17 +0000 (15:23 -0600)]
rockchip: Use rockchip_get_clk() to obtain the SoC clock
The current code picks the first available clock. In U-Boot proper this is
the oscillator device, not the SoC clock device. As a result the HDMI display
does not work.
Fix this by calling rockchip_get_clk() instead.
Fixes: 135aa950 (clk: convert API to match reset/mailbox style) Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Simon Glass [Sun, 17 Jul 2016 21:23:16 +0000 (15:23 -0600)]
rockchip: Add a way to obtain the main clock device
On Rockchip SoCs we typically have a main clock device that uses the Soc
clock driver. There is also a fixed clock for the oscillator. Add a function
to obtain the core clock.
Simon Glass [Sun, 17 Jul 2016 21:23:15 +0000 (15:23 -0600)]
dm: core: Add a way to find a device by its driver
Some SoCs have a single clock device. Provide a way to find it given its
driver name. This is handled by the linker so will fail if the name is not
found, avoiding strange errors when names change and do not match. It is
also faster than a string comparison.
The function is very specific to the rk3288 in its arguments
referencing the rk3288 cru and grf and every other rockchip soc
has differing cru and grf registers. So make that function naming
explicit.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Glass <sjg@chromium.org>
cosmetic: rockchip: sort socs according to numbers
Having some sort of ordering proofed helpful in a lot of other places
already. So for a larger number of rockchip socs it might be helpful
as well instead of an ever increasing unsorted list.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org>
cosmetic: rockchip: rk3036: pinctrl: fix config symbol naming
Rockchip socs are always named rkxxxx in all places, as also shown
by the naming of the rk3036 pinctrl file itself.
Therefore also name the config symbol according to this scheme.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Glass <sjg@chromium.org>
This path doesn't support the fastboot flash function command entirely.
We will hit "cannot find partition" assertion without specified
partition environment. Define gpt partition layout in specified board
such as firefly-rk3288, then enjoy it!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Invalidate dcache before starting the DMA to ensure coherency. In case
there are any dirty lines from the DMA buffer in the cache, subsequent
cache-line replacements may corrupt the buffer in memory while the DMA
is still going on. Cache-line replacement can happen if the CPU tries to
bring some other memory locations into the cache while the DMA is going
on.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
So far, Rockchip SoCs have two kinds of USB2.0 phy, such as Synopsys and
Innosilicon. This patch applys dwc2 usb driver framework to implement
phy_init() and phy_off() methods for Synopsys phy on Rockchip platform.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 8 Jul 2016 03:30:58 +0000 (11:30 +0800)]
board: move all the rockchip board in one folder
The 'evb_rk3036' and 'kylin' is not a vendor name, let's replace them
to 'rockchip' which is a real _vendor_ name, and meet the architecure
'board/<vendor>/<board-name>/'.
More boards from rockchip like evb_rk3288, evb_rk3399 will comes later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Eddie Cai <eddie.cai.kernel@gmail.com>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
rockchip: add option to change method of loading u-boot
If we would like to boot from SD card, we have to implement mmc driver
in SPL stage, and get a slightly large SPL binary. Rockchip SoC's
bootrom code has the ability to load spl and u-boot, then boot.
If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to
bootrom in board_init_f(), then bootrom loads u-boot binary.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip: Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 25 Jul 2016 22:18:15 +0000 (18:18 -0400)]
sandbox: Migrate CONFIG_I2C_EEPROM
Most users of CONFIG_I2C_EEPROM were migrated to defconfig a while ago,
but sandbox was skipped. Leave it off for sandbox_spl where it does not
build, but does not need to be either.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Fri, 22 Jul 2016 15:22:49 +0000 (09:22 -0600)]
dtoc: Correct the type widening code in fdt_fallback
This code does not match the fdt version in fdt.py. When dtoc is unable to
use the Python libfdt library, it uses the fallback version, which does not
widen arrays correctly.
Fix this to avoid a warning 'excess elements in array initialize' in
dt-platdata.c which happens on some platforms.
Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Rini <trini@konsulko.com>
tools, rsa: Further minor cleanups on top of c236ebd and 2b9ec7
[NOTE: I took v1 of these patches in, and then v2 came out, this commit
is squashing the minor deltas from v1 -> v2 of updates to c236ebd and 2b9ec76 into this commit - trini]
- Added an additional NULL check, as suggested by Simon Glass to
fit_image_process_sig
- Re-formatted the comment blocks
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
[For merging the chnages from v2 back onto v1] Signed-off-by: Tom Rini <trini@konsulko.com>
ARM: am33xx: Always inhibit init/refresh during DDR phy init
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:
The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.
Signed-off-by: Russ Dill <Russ.Dill@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
In certain circumstances it comes in handy to be able to boot into a second
U-Boot. But as of now it is not possible to boot a U-Boot binary that is inside
a FIT image, which is problematic for projects that e.g. need to guarantee a
unbroken chain of trust from SOC all the way into the OS, since the FIT signing
mechanism cannot be used.
This patch adds the capability to load such FIT images.
An example .its snippet (utilizing signature verification) might look
like the following:
commit 1f807a9f32aa ("ARM: keystone2: Refactor MSMC macros to avoid
left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid.
This, in effect disabled DMA coherency for QM PDSP.
Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs,
the #ifdef should been removed in the first place. Do the same.
A feasible way to communicate certain errors for devices that have no
other way of signalling besides LEDs is to flash these LEDs. For errors
in U-Boot, a script that utilizes the led and sleep commands would be a
practicable way, but currently the sleep command can only delay for an
integral amount of seconds, which is too slow to create an easily
noticeable pattern for flashing LEDs.
Therefore, this patch adds support for fractions (down to .001 seconds)
to the sleep command.
The parsing is kept minimal, simplistic and as robust as possible: After
converting the passed string using simple_strtoul and multiplying it
with 1000, we search for the first dot, convert the three characters
after that into a number (if they are not numbers, we ignore the
fractional part and just use the delay we got from simple_strtoul), and
add this number to the delay.
mtd: nand: fix bug writing 1 byte less than page size
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write, although
it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating until the watchdog timeout triggers.
To reproduce the issue on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
projects / u-boot / log