Alexey Brodkin [Thu, 10 Dec 2015 13:56:42 +0000 (16:56 +0300)]
axs103: add support of generic OHCI USB 1.1 controller
This commit adds support of USB 1.1 storage media on AXS103 board.
For some yet unknown reason USB 2.0 doesn't work on AXS103 board issuing
messages like this:
------------------------>8-------------------
AXS# usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
------------------------>8-------------------
As a work-around we're falling back to USB 1.1.
Indeed it is much slower but at least USB storage devices are usable on
AXS103.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org>
Karsten Merker [Wed, 16 Dec 2015 19:59:40 +0000 (20:59 +0100)]
sunxi: Enable a second mmc socket as boot target in the environment
Some sunxi-based boards (such as the Olimex A20-SOM-EVB) have a
second MMC socket. This socket is not bootable hardware-wise,
i.e. u-boot itself cannot be loaded from it, but once u-boot has
started, the second socket can be used in the boot process
provided by config_distro_bootcmd.h.
If a second MMC socket is present, place it in the boot order
after the first MMC socket.
Signed-off-by: Karsten Merker <merker@debian.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Karsten Merker [Wed, 16 Dec 2015 19:59:39 +0000 (20:59 +0100)]
sunxi: A20-Olimex-SOM-EVB defconfig: enable mmc3
The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. The baseboard provides a full-size SD
socket (connected to mmc3) in addition to the micro-SD socket on
the SOM itself (which is connected to mmc0).
Enable the mmc3 controller in the board defconfig.
Signed-off-by: Karsten Merker <merker@debian.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In order to re-use as much Cyclone5 and Arria5 code as possible to support
the Arria10 platform, we need to wrap some of the code with #ifdef's. By
adding CONFIG_TARGET_SOCFPGA_GEN5, we can shorten the check by not having to check
for both AV || AV.
Marek Vasut [Sat, 5 Dec 2015 20:07:23 +0000 (21:07 +0100)]
arm: socfpga: Introduce common board code
The SoCFPGA has reached a point where every single board code become
the same, since each and every single board is probed equally from OF.
Move the common board code into arch/arm/mach-socfpga/ .
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 5 Dec 2015 19:08:21 +0000 (20:08 +0100)]
arm: socfpga: Switch CONFIG_HOSTNAME to CONFIG_SYS_BOARD
We already have the CONFIG_SYS_BOARD variable, which defines the name
of the board. The value in CONFIG_HOSTNAME is exactly the same and is
thus just a duplicity, so switch it to reuse CONFIG_SYS_BOARD .
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 5 Dec 2015 19:05:46 +0000 (20:05 +0100)]
arm: socfpga: Switch CONFIG_G_DNL_MANUFACTURER to CONFIG_SYS_VENDOR
We already have the CONFIG_SYS_VENDOR variable, which defines the
manufacturer of the board. The value in CONFIG_G_DNL_MANUFACTURER
is just a duplicity, so switch it to reuse CONFIG_SYS_VENDOR .
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 5 Dec 2015 18:24:22 +0000 (19:24 +0100)]
arm: socfpga: socrates: Probe DWC2 UDC from OF instead of hard-coded data
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Marek Vasut [Sat, 5 Dec 2015 18:24:22 +0000 (19:24 +0100)]
arm: socfpga: sockit: Probe DWC2 UDC from OF instead of hard-coded data
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Marek Vasut [Sat, 5 Dec 2015 18:24:22 +0000 (19:24 +0100)]
arm: socfpga: mcvevk: Probe DWC2 UDC from OF instead of hard-coded data
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Marek Vasut [Sat, 5 Dec 2015 18:24:22 +0000 (19:24 +0100)]
arm: socfpga: de0_nano: Probe DWC2 UDC from OF instead of hard-coded data
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Marek Vasut [Sat, 5 Dec 2015 18:24:22 +0000 (19:24 +0100)]
arm: socfpga: cyclone5-socdk: Probe DWC2 UDC from OF instead of hard-coded data
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Marek Vasut [Sat, 5 Dec 2015 18:24:22 +0000 (19:24 +0100)]
arm: socfpga: arria5-socdk: Probe DWC2 UDC from OF instead of hard-coded data
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Marek Vasut [Sat, 5 Dec 2015 16:41:58 +0000 (17:41 +0100)]
net: phy: micrel: Configure KSZ9021/KSZ9031 skew from OF
Add code to process the KSZ9021/KSZ9031 OF props if they are present
and configure skew registers based on the information from the OF.
This code is only enabled if the DM support for ethernet is also
enabled.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
V2: - Implement struct ksz90x1_reg_field to describe the skew register
fields more accurately.
- Fix RXDV/TXEN skew register default value and offset.
Marek Vasut [Wed, 16 Dec 2015 00:32:47 +0000 (01:32 +0100)]
nios2: Enable support for fitImage
The uImage format is legacy for years now, enable support for the
fitImage format, which allows combining multiple files (kernel and
dtb) into a single file, offers better protection of the payload
and so on.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Marek Vasut [Tue, 15 Dec 2015 02:09:24 +0000 (03:09 +0100)]
nios2: Preconfigure $loadaddr variable
Preset the $loadaddr environment variable to some sane default, let's
say half of the RAM. This variable is where the kernel is loaded using
all sorts of .*load commands, so it's convenient to have it set.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Marek Vasut [Tue, 15 Dec 2015 02:09:23 +0000 (03:09 +0100)]
nios2: Up the monitor size to 512kiB
The monitor is growing much larger with various additions, like fitImage,
command line completion, UBI etc. Make the monitor area larger so these
features can be safely added.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Marek Vasut [Tue, 15 Dec 2015 02:09:22 +0000 (03:09 +0100)]
nios2: Calculate the env position from monitor size
Reorder the 10m50 and 3c120 config files such, that the environment
position can be calculated from the monitor size. The environment is
placed right after the monitor. This removes one more ad-hoc variable.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Nathan Rossi [Tue, 8 Dec 2015 14:44:42 +0000 (00:44 +1000)]
arm: zynq: Update ZYBO config options
Update the ZYBO device tree and enable config options that relate to the
added devices in the device tree.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nathan Rossi [Tue, 8 Dec 2015 14:44:40 +0000 (00:44 +1000)]
spi: zynq_qspi: Add configuration to disable LQSPI feature
When the Zynq Boot ROM code loads the payload from QSPI it uses the
LQSPI feature of the QSPI device, however it does not clean up its
configuration before handing over to the payload which leaves the device
confgured to by-pass the standard non-linear operating mode.
This ensures the Linear QSPI mode is disabled before re-enabling the
device.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Jagan Teki <jteki@openedev.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nathan Rossi [Tue, 24 Nov 2015 09:34:09 +0000 (19:34 +1000)]
ARM: zynq: Add default ps7_init_gpl.c/h for ZYBO
Add ps7_init_gpl.c/h for the ZYBO board. This instance of the ps7_init
is generated by the Vivado 2015.3 tools using the system configuration
provided by Digilent located on their website.
Update the kconfig so that the defconfig is not overrided to use the
custom init ps7_init_gpl target by default.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stephen Warren [Fri, 13 Nov 2015 20:34:09 +0000 (13:34 -0700)]
usb: kbd: don't use int xfers when polling via ctrl xfers
When CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP is enabled, use a
GET_REPORT control transfer to retrieve the initial state of the
keyboard. This matches the technique used to poll the keyboard state.
This is useful since it eliminates the remaining use of interrupt
transfers from the USB keyboard driver, which allows it to work with
USB HCD that don't support interrupt transfers.
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Alexey Brodkin [Mon, 14 Dec 2015 14:18:50 +0000 (17:18 +0300)]
usb: add support of generic OHCI devices
This driver is meant to be used with any OHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Simon Glass <sjg@chromium.org> Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Thu, 10 Dec 2015 15:32:25 +0000 (16:32 +0100)]
usb: host: ehci: samsung: Move hcor initialization after usb phy setup
With the old order of initialization the hcor pointer has been setup to
the same address as Exynos EHCI base address (0x12110000 instead of
0x12110010).
Such behaviour was caused by reading value of 0 instead of 0x10 from EHCI
HCCPBASE register without doing proper clock initialization before.
To fix this problem hcor initialization has been moved after USB PHY setup.
Now ehci_readl(&ctx->hcd->cr_capbase) returns correct value.
Marek Vasut [Wed, 19 Aug 2015 21:27:26 +0000 (23:27 +0200)]
usb: s3c-otg: Rename USB_GADGET_S3C_UDC_OTG* to USB_GADGET_DWC2_OTG*
The s3c-otg IP block is in fact a DWC2 OTG one, so finally rename the
config option to make it less misleading. No functional change, just
a mechanical change done using the following script:
git grep USB_GADGET_S3C_UDC_OTG | cut -d : -f 1 | sort -u | \
while read line ; do
sed -i "s/USB_GADGET_S3C_UDC_OTG/USB_GADGET_DWC2_OTG/g" $line ;
done
Marek Vasut [Fri, 4 Dec 2015 01:34:46 +0000 (02:34 +0100)]
usb: s3c-otg: Rename sources to dwc2_*c
The driver is actually for the Designware DWC2 controller.
This patch renames the local source files to dwc2_*c and
adjusts the Makefile to use the new names.
Marek Vasut [Fri, 4 Dec 2015 01:32:22 +0000 (02:32 +0100)]
usb: s3c-otg: Rename local headers to dwc2_*h
The driver is actually for the Designware DWC2 controller.
This patch renames the local header files to dwc2_*h and
adjusts the sources to use the new names.
Marek Vasut [Fri, 4 Dec 2015 01:03:45 +0000 (02:03 +0100)]
usb: s3c-otg: Rename s3c_udc_*() functions
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep_*() functions to reflect this.
The function s3c_udc_probe() is a special case and is not
renamed by this patch yet.
Marek Vasut [Fri, 4 Dec 2015 00:44:41 +0000 (01:44 +0100)]
usb: s3c-otg: Rename struct s3c_usbotg_phy to dwc2_usbotg_phy
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_phy to struct dwc2_usbotg_phy
to make things more obvious and clear.
Marek Vasut [Fri, 4 Dec 2015 00:36:36 +0000 (01:36 +0100)]
usb: s3c-otg: Split private bits from s3c_udc.h
Most of the functions are local to the s3c_udc driver, remove them
from the s3c_udc.h header to stop those bits from propagating all
over the place. Instead, move all the private stuff into new private
s3c_udc_otg_priv.h header.
Marek Vasut [Fri, 4 Dec 2015 00:11:45 +0000 (01:11 +0100)]
usb: s3c-otg: Rename struct s3c_usbotg_reg to dwc2_usbotg_reg
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_reg to struct dwc2_usbotg_reg
to make things more obvious and clear.
Shaohui Xie [Fri, 4 Dec 2015 02:22:03 +0000 (10:22 +0800)]
net: fm: disables unused FM1-DTSEC1 MAC node in DTS
We don't disable unused FM1-DTSEC1 MAC node in FMAN v2 since it is
used by MDIO. For FMAN v3, MDIO uses dedicated controller, so we
can disable unused FM1-DTSEC1 MAC node to avoid being probed in
Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revised commit message] Reviewed-by: York Sun <yorksun@freescale.com>
Mingkai Hu [Mon, 7 Dec 2015 08:58:54 +0000 (16:58 +0800)]
armv8/ls1043a: Implement workaround for PEX erratum A009929
Consecutive write transactions from core to PCI express outbound
path hangs after 25 to 30 transactions depending on core freq.
This erratum enable the mbist clock through COP register setting.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 3 Dec 2015 21:14:04 +0000 (15:14 -0600)]
driver: net: fsl-mc: remove MC firmware version check
The MC version numbers provide no meaningful information
about binary interface compatibility, so remove the
check which refuses to start the MC unless a specific
version is found.
Version checking is supposed to be done at the individual
object level, and individual drivers are responsible
for their own version checking.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Acked-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
projects / u-boot / log