Joe Hershberger [Mon, 8 Apr 2013 10:32:50 +0000 (10:32 +0000)]
mtd: Make mtdparts work with pre-reloc env
The env in UBI needs to look up the mtd partition as part of relocation,
which happens before relocation. Make the mtdparts code capable of
working on the default env to start with.
The code tries to set values in the env as well, but again, the env
isn't there yet, so add a check to setenv to not allow sets before the
env is relocated.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
powerpc/lib: fix unsafe register handling in wait_ticks
If watchdog is enabled, the arch/powerpc/lib/ticks.S::wait_ticks() function
calls the function specified by the WATCHDOG_RESET macro.
The wait_ticks function depends on the registers r0, r6 and r7 being
preserved however that is not guaranteed, e.g. if the reset function is a
C function this will probably overwrite r0 and cause an endless loop.
The following patch changes to using r14+r15 instead of r6+r7 (to resemble
what would have been generated by a C compiler) and saves all necessary
registers on the stack.
The patch has been tested on a custom MPC5125 based machine using the 512x
powerpc architecture.
Signed-off-by: Mats Karrman <mats.karrman@tritech.se> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Tested-by: Stefan Roese <sr@denx.de>
ramneek mehresh [Sun, 17 Feb 2013 18:23:32 +0000 (18:23 +0000)]
powerpc/usb: Fix usb device-tree fix-up
Fix USB device-tree fixup to properly handle device-tree fixup and
print appropriate message when wrong/junk "dr_mode" or "phy_type"
are mentioned in hwconfig string
am335x_evm: Enable DFU for NAND and MMC, provide example alt_infos
- Add CONFIG_DFU_NAND, CONFIG_DFU_MMC
- Set dfu_alt_info_nand, dfu_alt_info_emmc and dfu_alt_info_mmc to show
working examples for those cases.
- Increase CONFIG_SYS_MAXARGS due to hush parsing bugs that would
otherwise disallow 'setenv dfu_alt_info ${dfu_alt_info_nand}'.
- Enable CONFIG_FAT_WRITE to allow updating on MMC
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 14 Mar 2013 05:32:50 +0000 (05:32 +0000)]
nand: Extend nand_(read|write)_skip_bad with *actual and limit parameters
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Previously we didn't support upload/download larger than available
memory. This is pretty bad when you have to update your root filesystem
for example.
This patch removes that limitation (and the crashes when you transfered
any file larger than 4MB) by making raw image writes be done in chunks
and making file maximum size be configurable.
The sequence number is a 16 bit counter; make sure we handle rollover
correctly. This fixes the wrong transfers for large (> 256MB) images.
Also utilize a variable to handle initialization, so that we don't rely
on just the counter sent by the host.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 26 Mar 2013 13:09:44 +0000 (13:09 +0000)]
patman: Add Series-process-log tag to sort/uniq change logs
For some series with lots of changes it is annoying that duplicate change
log items are not caught. It is also helpful sometimes to sort the change
logs.
Add a Series-process-log tag to enable this, which can be placed in a
commit to control this.
The change to the Cc: line is to fix a checkpatch warning.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:43 +0000 (13:09 +0000)]
patman: Add -a option to refrain from test-applying the patches
Especially with the Linux kernel, it takes a long time (a minute or more)
to test-apply the patches, so patman becomes significantly less useful.
The only real problem that is found with this apply step is trailing spaces.
Provide a -a option to skip this step, for those working with clean patches.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Doug Anderson [Fri, 1 Mar 2013 11:11:07 +0000 (11:11 +0000)]
patman: Don't barf if the word 'commit' starts a line
Patman's regular expression for detecting the start of a
commit in a git log was a little simplistic and could be
confused if the git log itself had the word "commit" as
the start of a line (as this commit does). Make patman
a little more robust.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:42 +0000 (13:09 +0000)]
patman: Provide option to ignore bad aliases
Often it happens that patches include tags which don't have aliases. It
is annoying that patman fails in this case, and provides no option to
continue other than adding empty tags to the .patman file.
Correct this by adding a '-t' option to ignore tags that don't exist.
Print a warning instead.
Since running the tests is not a common operation, move this to --test
instead, to reserve -t for this new option.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Mingkai Hu [Sun, 7 Apr 2013 22:13:32 +0000 (22:13 +0000)]
cmd_sf: include header file common.h before div64.h
The header file div64.h includes <asm/types.h> which defines
the phys_addr_t according to the macro CONFIG_PHYS_64BIT, while
the macro CONFIG_PHYS_64BIT is included in common.h which comes
after div64.h, so in order to get consistent type definition for
phys_addr_t, common.h should be included before div64.h, Or else,
the parameters of phys_addr_t type will be passed wrongly when
CONFIG_PHYS_64BIT is defined.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
introduced cleanup of ext4write semantics to be consistent with other
filesystem's writing commands (e.g. fatwrite).
This commit provides correct ext4write command generation at DFU eMMC
code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Simon Glass [Wed, 3 Apr 2013 11:07:16 +0000 (11:07 +0000)]
buildman - U-Boot multi-threaded builder and summary tool
This tool handles building U-Boot to check that you have not broken it
with your patch series. It can build each individual commit and report
which boards fail on which commits, and which errors come up. It also
shows differences in image sizes due to particular commits.
Buildman aims to make full use of multi-processor machines.
Documentation and caveats are in tools/buildman/README.
Simon Glass [Tue, 26 Mar 2013 13:09:40 +0000 (13:09 +0000)]
patman: Don't allow spaces in tags
At present something like:
Revert "arm: Add cache operations"
will try to use
Revert "arm
as a tag. Clearly this is wrong, so fix it.
If the revert is intended to be tagged, then the tag can come before
the revert, perhaps. Alternatively the 'Cc' tag can be used in the commit
messages.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:39 +0000 (13:09 +0000)]
patman: Fix up checkpatch parsing to deal with 'CHECK' lines
checkpatch has a new type of warning, a 'CHECK'. At present patman fails
with these, which makes it less than useful.
Add support for checks, making it backwards compatible with the old
checkpatch.
At the same time, clean up formatting of the CheckPatches() output,
fix erroneous "internal error" if multiple patches have warnings and
be more robust to new types of problems.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Simon Glass [Wed, 20 Mar 2013 16:43:00 +0000 (16:43 +0000)]
patman: Add Cover-letter-cc tag to Cc cover letter to people
The cover letter is sent to everyone who is on the Cc list for any of
the patches in the series. Sometimes it is useful to send just the cover
letter to additional people, so that they are aware of the series, but
don't need to wade through all the individual patches.
Add a new Cover-letter-cc tag for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Doug Anderson [Fri, 15 Mar 2013 13:24:05 +0000 (13:24 +0000)]
patman: Make "Reviewed-by" an important tag
Although "Reviewed-by:" is a tag that gerrit adds, it's also a tag
used by upstream. Stripping it is undesirable. In fact, we should
treat it as important.
Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 15 Dec 2012 10:42:06 +0000 (10:42 +0000)]
patman: Allow reading metadata from a list of commits
We normally read from the current branch, but buildman will need to look
at commits from another branch. Allow the metadata to be read from any
list of commits, to provide this flexibility.
Simon Glass [Sat, 15 Dec 2012 10:42:05 +0000 (10:42 +0000)]
patman: Allow commands to raise on error, or not
Make raise_on_error a parameter so that we can control which commands
raise and which do not. If we get an error reading the alias file, just
continue.
Simon Glass [Sat, 15 Dec 2012 10:42:04 +0000 (10:42 +0000)]
patman: Make command methods return a CommandResult
Rather than returning a list of things, return an object. That makes it
easier to access the returned items, and easier to extend the return
value later.
Simon Glass [Sat, 15 Dec 2012 10:42:03 +0000 (10:42 +0000)]
patman: Add cros_subprocess library to manage subprocesses
This adds a new library on top of subprocess which permits access to
the subprocess output as it is being generated. We can therefore
give the illusion that a process is running independently, but still
monitor its output so that we know what is going on.
It is possible to display output on a terminal as it is generated
(a little like tee). The supplied output function is called with all
stdout/stderr data as it arrives.
Simon Glass [Sat, 15 Dec 2012 10:42:01 +0000 (10:42 +0000)]
patman: Use ANSI colours only when outputting to a terminal
It is easy to detect whether or not the process is connected to a terminal,
or piped to a file. Disable ANSI colours automatically when output is
not to a terminal.
Stefan Roese [Wed, 3 Apr 2013 00:47:46 +0000 (02:47 +0200)]
cfi_flash: Use uintptr_t for casts from u32 to void *
This fixes this build warning:
Configuring for qemu_mips64 - Board: qemu-mips64, Options: SYS_BIG_ENDIAN
text data bss dec hex filename
215344 13082 218720 447146 6d2aa qemu_mips64/u-boot
cfi_flash.c: In function 'flash_map':
cfi_flash.c:217:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com>
This makes sure we have inline functions such as inb/outb that
are used in these two files by including the arch-specific
<asm/io.h> header. However the ARM version does not provide the
accessors unless the config symbol __io is also defined so add
that in front of the include.
After this the bios emulator will compile on ARM systems.
Stephen Warren [Mon, 1 Apr 2013 11:50:28 +0000 (11:50 +0000)]
mmc: don't allow extra cmdline arguments
The "mmc rescan" command takes no arguments. However, executing
"mmc rescan 1" succeeds, leading the user to believe that MMC device 1
has been rescanned. In fact, the "current" MMC device has been
rescanned, and the current device may well not be 1. Add error-checking
to the "mmc" command to explicitly reject any extra command-line
arguments so that it's more obvious when U-Boot isn't doing what the
user thought they asked it to.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Albert ARIBAUD [Sat, 30 Mar 2013 00:19:53 +0000 (00:19 +0000)]
replace last __bss_end__ occurrences with __bss_end
Simon Glass' commit 3929fb0a141530551b3fce15ee08629f80d5ef2a,
which changed all occurrences of __bss__end__ into __bss_end,
left behind some untouched __bss_end__ occurrences in all 33
u-boot.lds.debug files, in board/mousse/u-boot.lds.ram and
in board/mousse/u-boot.lds.rom. These are replaced here.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Rob Herring [Fri, 22 Mar 2013 11:26:21 +0000 (11:26 +0000)]
env: fix potential stack overflow in environment functions
Most of the various environment functions create CONFIG_ENV_SIZE buffers on
the stack. At least on ARM and PPC which have 4KB stacks, this can overflow
the stack if we have large environment sizes. So move all the buffers off
the stack to static buffers.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
mtd: cfi_flash: Fix CFI flash driver for 8-bit bus support
This commit is based on that patch from aaron.williams@caviumnetworks.com
with same commit title. pulled the same code changes into current u-boot tree.
This patch corrects the addresses used when working with Spansion/AMD FLASH chips.
Addressing for 8 and 16 bits is almost identical except in the 16-bit case the
LSB of the address is always 0. The confusion arose because the addresses
in the datasheet for 16-bit mode are word addresses but this code assumed it was
byte addresses.
I have only been able to test this on our Octeon boards which use either an 8-bit
or 16-bit bus. I have not tested the case where there's an 8-bit part on a 16-bit
bus.
This patch also adds some delays as suggested by Spansion.
If a part can be both 8 and 16-bits, it forces it to work in 8-bit mode if an
8-bit bus is detected.
Apart from the pulled changes, fixed few minor code cleanups and tested
on 256M29EW, 512M29EW flashes.
Before this fix:
---------------
Bank # 1: CFI conformant flash (8 x 8) Size: 64 MB in 512 Sectors
AMD Standard command set, Manufacturer ID: 0xFF, Device ID: 0xFF
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
After this fix:
--------------
Bank # 1: CFI conformant flash (8 x 8) Size: 64 MB in 512 Sectors
AMD Standard command set, Manufacturer ID: 0x89, Device ID: 0x7E2301
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com> Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* in CONFIG_PREBOOT try load bootmenu.scr from first partition
of internal eMMC memory (also known as MyDocs) which (should)
overwrite default bootmenu entries
* when keyboard slide is closed boot first menu entry
Pali Rohár [Sat, 23 Mar 2013 14:53:08 +0000 (14:53 +0000)]
New command bootmenu: ANSI terminal boot menu support
The "bootmenu" command uses U-Boot menu interfaces and provides
a simple mechanism for creating menus with several boot items.
When running this command the menu will be assembled as defined
by a set of environment variables which contain a title and
command key-value pairs. The "Up" and "Down" keys are used for
navigation through the items. Current active menu item is
highlighted and can be selected using the "Enter" key.
The command interprets and generates various ANSI escape
sequencies, so for proper menu rendering and item selection
the used terminal should support them.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[agust: various fixes and documentation updates] Signed-off-by: Anatolij Gustschin <agust@denx.de>
Checking the default menu item and obtaining its data can
be useful in custom menu code. Export menu_default_choice()
function which serves this purpose.
Pali Rohár [Sat, 23 Mar 2013 14:50:40 +0000 (14:50 +0000)]
menu: Add support for user defined item choice function
Selecting menu items is currently done in menu_interactive_choice()
by reading the user input strings from standard input.
Extend menu_interactive_choice() to support user defined function
for selecting menu items. This function and its argument can be
specified when creating the menu.
R Sricharan [Mon, 4 Mar 2013 20:04:45 +0000 (20:04 +0000)]
ARM: mmu: Set domain permissions to client access
The 'XN' execute never bit is set in the pagetables. This will
prevent speculative prefetches to non executable regions. But the
domain permissions are set as master in the DACR register.
So the pagetable attribute for 'XN' is not effective. Change the
permissions to client.
This fixes lot of speculative prefetch aborts seen on OMAP5
secure devices.
Signed-off-by: R Sricharan <r.sricharan@ti.com> Tested-by: Vincent Stehle <v-stehle@ti.com> Cc: Vincent Stehle <v-stehle@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
R Sricharan [Mon, 4 Mar 2013 20:04:44 +0000 (20:04 +0000)]
ARM: mmu: Introduce weak dram_bank_setup function
Introduce a weak version of dram_bank_setup function
to allow a platform specific function.
This is used in the subsequent patch to setup dram region
without 'XN' attribute in order to enable the region
under client permissions.
Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Vincent Stehle <v-stehle@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tom Rini [Wed, 20 Mar 2013 04:21:38 +0000 (04:21 +0000)]
cmd_ext4: BREAK and correct ext4write parameter order
The ext4write command was taking the in-memory address and filename path
in reverse order from the rest of the filesystem read and write
commands. This corrects the order to be the same as fatload, etc.
Tom Rini [Thu, 14 Mar 2013 05:36:13 +0000 (05:36 +0000)]
checkpatch.pl: Add 'debug' to the list of logFunctions
While the kernel mainly uses pr_debug(...), etc, for debug messages, we
use debug(...). Add this to the list of logFunctions so that they are
correctly checked (and not warned against) for long string literals.
Tom Warren [Mon, 18 Mar 2013 21:52:26 +0000 (14:52 -0700)]
Tegra114: MMC: Enable DT MMC driver support for Tegra114 Dalmore boards
Tested on my Dalmore E1611 board, eMMC and SD-Card work fine, can load
a kernel off of an SD card OK, card detect works, and the env is now
stored in eMMC (end of the 2nd 'boot' sector, same as Tegra20/30).
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Allen Martin [Sat, 16 Mar 2013 18:58:07 +0000 (18:58 +0000)]
spi: add common fdt SPI driver interface
Add a common interface to fdt based SPI drivers. Each driver is
represented by a table entry in fdt_spi_drivers[]. If there are
multiple SPI drivers in the table, the first driver to return success
from spi_init() will be registered as the SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Allen Martin [Sat, 16 Mar 2013 18:58:02 +0000 (18:58 +0000)]
tegra: remove support for UART SPI switch
This feature was only used for tegra20 seaboard that had a pinmux
conflict on the SPI pins. These boards were never manufactured, so
remove this support to clean up SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Peter Korsgaard [Thu, 21 Mar 2013 04:00:03 +0000 (04:00 +0000)]
mmc: mmc_getcd/getwp: use sensible defaults
Let mmc_getcd() return true and mmc_getwp() false if mmc driver doesn't
provide handlers for them.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Add braces around first if test in each case to fix warning] Signed-off-by: Tom Rini <trini@ti.com>
projects / u-boot / log