Steven Stallion [Sat, 16 Jul 2016 03:01:00 +0000 (22:01 -0500)]
rtos: add support for uC/OS-III
This patch introduces RTOS support for uC/OS-III. Currently, only
FPU-less ARM Cortex-M targets are supported. Due to the configurability
of the RTOS, an OpenOCD-specific file must be linked along with the
project to determine the correct offsets within the OS_TCB structure.
In addition to the above, a crash was fixed in rtos_get_gdb_reg_list
such that RTOS support could be used between resets without restarting
OpenOCD and support for the Hg packet was cleaned up.
Change-Id: Ide004a689e6b886185df665c00fb644629eb31d1 Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3556 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jiri Kastner [Fri, 11 Nov 2016 09:50:13 +0000 (10:50 +0100)]
dap_dp_init: remove loop
current loop sounds to me like 'we don't know what we do, let's do it ten times, maybe we will have luck'.
should be enough to 'ping' debug port using reading CRTL_STAT.
tested on cortex-a8, snapdragon, jetson k1, cortex-r5, cortex-r4
cortex_a: remove partnum magic from arp_examine and dbginit
Depending on the Debug implementation the "OS Lock" feature might be
implemented or not. It is not actually depending on the part number of the
implemented ARM core but on the DBGOSLSR.OSLM bits. This patch removes
querying the part number and implements proper parsing of OSLM. Result is
a more generic approach that will work out-of-box on more devices.
Add -defer-examine option to target create command
The '-defer-examine' option to target create allows declaring targets
that are present on the chain, but not fully functional. They will
be skipped by the initial arp_examine as well as arp_examine after
reset.
Manual examine using 'arp_examine' is needed to examine them, with the
idea that some kind of actions is neeed to bring them to a state where
examine will succeed (if at all possible).
In order to allow value less options to target command, I had to relax
the goi.argc check in jim_target_configure().
Tomas Vanek [Mon, 18 Jul 2016 20:59:17 +0000 (22:59 +0200)]
flash/nor: at91samd protection bits write fix
Flash protection set on a device with MANW=1 was lost after reset.
Since #2903 the driver honored MANW bit and issued Write Page command just
for main flash write. This change adds similar technique to
samd_modify_user_row().
Minor code improvements:
samd_check_error() returns error code corresponding to error type
instead of bool.
samd_check_error() does not clear STATUS register if no error bit is set.
Eliminated double error check in call sequence samd_issue_nvmctrl_command()
folowed by samd_check_error().
Missing error code ERROR_FLASH_PROTECTED added to src/flash/common.h.
Change-Id: Icf59ab8803305d0cb3170c8a5089b8f9828b99f8 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3550 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Wed, 24 Aug 2016 09:18:41 +0000 (11:18 +0200)]
tcl at91samdXX.cfg: update config to current OpenOCD status
Remove comment about workaround of not working 'reset halt' - not needed
as 'reset halt' is working as expected @ EDBG with srst_only.
Add srst_pulls_trst to reset_config as it no more triggers an error.
Change-Id: I47cf445690c46ccfb866900cddbfcaefc8649f82 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3722 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Marc Schink [Sun, 24 Jul 2016 11:06:33 +0000 (13:06 +0200)]
Fix autogen.sh invocation of libjaylink
Move autogen.sh invocation of libjaylink from the configure to the
bootstrap script because the configure script is included in tarball
releases but autotools are not required to be available on end-user
machines.
Thanks to Paul Fertser for spotting this.
Change-Id: I5489ae83885157a01803eed51a7328e47d67ea6d Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3569 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tomas Vanek [Wed, 27 Jul 2016 14:50:25 +0000 (16:50 +0200)]
flash at91samd, at91sam4l: fix improper use of mem_ap_ call
Since merge of #3149 OpenOCD start with an unresponsive SAMD or SAM4L
resulted in segfaults. First was in cortex_m_assert_reset
(fixed by #3552), second was in samd_handle_reset_deassert()
/sam4l_handle_reset_deassert().
The change replaces mem_ap_write_u32/8 by target_write_u32/8.
It also takes better care about examining and polling target before
debug control registers are set. It prevents lockup when 'reset halt'
is issued on unresponsive cpu.
Change-Id: I2516489f4771aebfc1118d174f527497b8a201ad Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3603 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Thu, 3 Nov 2016 14:31:33 +0000 (17:31 +0300)]
flash: nor: mdr: do not mass erase when clearing INFO memory
The MDR parts have two kinds of memory: main (regular memory-mapped
memory for code and data) and "info" (not memory-mapped). When OpenOCD
is requested to erase the info memory block, it should do just that,
instead of erasing everything including main memory.
Change-Id: I498142ca50d4a7b669b7776180b0dbcea63a5328 Reported-by: Eldar Khayrullin <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3853 Tested-by: jenkins Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On multi-core systems, with some cores in power-down state, examination
will fail for these cores. Make sure assert- and deassert_reset functions
don't crash due to uninitialized variables.
HarishKumar [Tue, 9 Dec 2014 14:08:08 +0000 (19:38 +0530)]
Tcl commands: Fix improper return status in flash commands and load_image.
Nand write command :
nand_fileio_cleanup() always returns ERROR_OK. Due to this,
handle_nand_write_command() retuns ERROR_OK in the case
of nand failure. ERROR_FAIL should be returned.
Flash erase_sector command :
handle_flash_erase_command() always returns ERROR_OK even if
the erase functionality of actual driver implementation fails.
retval value should be returned.
Flash write_bank command :
handle_flash_write_bank_command() returns ERROR_OK even if
fileio_open() and fileio_read fails. ERROR_FAIL should be
returned.
Load_image command :
handle_load_image_command() retuns ERROR_OK even if image_open()
fails. ERROR_FAIL should be returned.
When the buffer is null, breaking the loop without setting
retval = ERROR_FAIL would cause load_image to return ERROR_OK.
Tim Newsome [Wed, 5 Oct 2016 14:57:38 +0000 (07:57 -0700)]
Perform small writes before sending OK.
To speed up downloads, OpenOCD sends gdb OK when a write is received,
even before the write has actually occurred. The failure is then
returned for the next write. That leads to the following confusing
behavior:
```
(gdb) p/x *((int*)0xdeadbeef)=8675309
$2 = 0x845fed
(gdb) p/x *((int*)0x80000000)=6874742
Cannot access memory at address 0x80000000
```
While it's actually the first write that failed.
This change hacks around this problem by not sending OK for small writes
(len<8) until the write has actually occurred. This does not impact
download speed, since during downloads (almost) all writes will have
much larger length.
Change-Id: I1f8b9bb19b0707487f840df6871e372e4ba228dd Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/3803 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Andreas Färber [Sun, 8 May 2016 21:49:07 +0000 (23:49 +0200)]
flash/nor: Add erased_value to drivers and pass it to targets
struct flash_driver has a default_padded_value field that is similar,
but it can be changed by the user for the specific purpose of padding.
Add a new erased_value field and initialize it for all targets,
particularly stm32lx, xmc4xxx and virtual.
Use this value in core.c:default_flash_mem_blank_check(), the slow path.
Extend the target API to pass erased_value down to target code.
Adding an argument ensures that we catch all callers.
This allows us to merge xmc4xxx.c:xmc4xxx_blank_check_memory() into
armv7m:armv7m_blank_check_memory().
It further allows us to use default_flash_blank_check() in place of
xmc4xxx.c:xmc4xxx_flash_blank_check(), adding a potential slow path
fallback, as well as stm32lx:stm32lx_erase_check(), adding the potential
armv7m fast path with fallback to default_flash_mem_blank_check().
Fix a mips32 code comment while at it (zeroed -> erased).
The armv4_5 and mips32 target implementations will now error out if an
erase value other than 0xff is used, causing default_flash_blank_check()
to fall back to the default_flank_mem_blank_check() slow path.
Change-Id: I39323fbbc4b71c256cd567e439896d0245d4745f Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3497 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Marc Schink [Sun, 22 May 2016 17:44:27 +0000 (19:44 +0200)]
helper: Make unhexify() robust on invalid data
The current implementation is not suitable for user provided data
because it does not detect invalid inputs in many cases. For example,
the string "aa0xbb" is successfully converted to the 3 bytes: 0xaa,
0x00 and 0xbb. An other example is "aabi" which is successfully
converted to the 2 bytes: 0xaa and 0x0b. Both are obviously incorrect.
Make unhexify() robust on invalid data and use more appropriate data
types for its parameters. Also, add a small documentation for the
function.
Change-Id: Idb799beb86fc608b066c8a76365021ed44c7f890 Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3792 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Marc Schink [Sun, 15 May 2016 11:25:46 +0000 (13:25 +0200)]
libjaylink: Update for API changes
Update to latest libjaylink version and incorporate API changes.
The major change in libjaylink is a rework of the device discovery.
Please test device discovery extensively, especially with multiple
devices connected. All other changes in libjaylink are of minor
importance for OpenOCD.
Change-Id: I9a50e83f59557505ce29809c7762c5df1cec10eb Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3735 Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Steven Stallion <stallion@squareup.com> Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Marc Schink [Tue, 16 Aug 2016 16:36:27 +0000 (18:36 +0200)]
jlink: Adjust log verbosity of libjaylink
Currently, the log verbosity of libjaylink is not accessible from the
user interface. Therefore, changing the log verbosity of libjaylink is
only possible from within the J-Link driver source code which is not
acceptable for end users.
Output the libjaylink log messages through the logging module of
OpenOCD rather than directly to stderr.
Change-Id: I6bf7bf8f4c8a12fb9e955eeced68224545fa0b5c Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3701 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Large flash parts time out when unlocking. Mass erase time is specified
as 32 seconds worst case for some parts. Automatic mass erase is
probably not using x8 parallelism, though, but a too large timeout
shouldn't hurt.
Also, use the new define instead of hardcoded timeout when mass
erasing.
Change-Id: Ib5af60d52ed7d53277bfe7176c4c44f79d3a26bc Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3738 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Robert Jordens [Mon, 21 Dec 2015 20:36:14 +0000 (13:36 -0700)]
xilinx_bscan_spi: port to new migen and clean-up
* port to new migen
* streamline package/part specification
* add pullup (Series3, Series6) and pullnone (Series7) for unused pins
as xilinx impact/vivado do it.
* specify respective toolchains
* build Series7 with vivado (broader support, faster)
* point to prebuilt bitstreams at https://github.com/jordens/bscan_spi_bitstreams
Change-Id: Ibfef3d78f855b754425f3e6131e2e49fa111e09a Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/3173 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins Reviewed-by: Robert Jördens Reviewed-by: William D. Jones Reviewed-by: Tim "mithro" Ansell <mithro@mithis.com>
Michael Dietz [Mon, 30 May 2016 08:54:47 +0000 (01:54 -0700)]
nRF51: Fix bug in Code memory size.
The code memory size was a bug and seemed to be working by
accident since there happened to be 256 pages in the device that was
tested on which corresponded to 256kb.
Also don't fail if memory size != expected memory size based on hwid
as this hwid is unstable and should be used only for debug/diagnostics.
Change-Id: I4e98f7498a36c53fc51783eddfdaba704d30e3ca Signed-off-by: Michael Dietz <mjdietzx@gmail.com>
Reviewed-on: http://openocd.zylin.com/3510 Tested-by: jenkins Reviewed-by: Jiří Pinkava <j-pi@seznam.cz> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently if ftdi device is removed, OpenOCD will stall forever.
Only kill -9 will help in this case.
This patch makes use of libusb timeout functions and
trying to break out of while loop if some error is detected.
Andreas Färber [Sat, 21 May 2016 22:41:15 +0000 (00:41 +0200)]
contrib/loaders: Enforce Little Endian ARM machine code
arm-none-eabi target triplet defaults to Little Endian, and so far any
submitted machine code snippets have been verified to be Little Endian.
However a user might override [ARM_]CROSS_COMPILE with an armeb toolchain,
potentially resulting in invalid machine code.
Let's be safe and enforce Little Endian mode for assembler and compiler.
Change-Id: I9cefe24689eaded25d60ffb1f254b254e8d76f9d Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3498 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Fri, 22 Jul 2016 10:28:42 +0000 (12:28 +0200)]
flash Kinetis: Implement flash protection setting
Kinetis family employs strange concept of Flash Configuration Field at
address 0x400 of program flash. Writing incorrect data to FCF may
permanently lock the device.
The change introduces 'kinetis fcf_source protection' mode. In this mode
write of flash image data to FCF is prevented. FCF data build from
protection (set by 'flash protect' command) are written instead.
FCF data are written also just after erase of relevant sector. It
protects device from locking security by reset or power cycle after erase.
prot_blocks array is used as protection blocks have bigger size than sectors.
Alignment and padding programming sections is rewritten to fix
writing with not section boundary aligned begin.
Change-Id: I9fc8bd37d6f627fb8ed7abb7f7560e78a740b195 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3562 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
Tomas Vanek [Fri, 22 Jul 2016 08:33:42 +0000 (10:33 +0200)]
flash Kinetis: refactoring ftfx commands and numerous minor changes
Add kinetis_ftfx_decode_error() to show flash error type in human
readable message.
Add kinetis_ftfx_prepare() to prepare flash module just once in
command (not each time kinetis_ftfx_command() is called).
Change target_read/write_memory() to target_read/write_u8/32().
Make ftfx_fstat parameter of kinetis_ftfx_command() optional.
Longword flash write:
Fix huge memory leak after write of unaligned block.
Check flash address alignment properly.
Do not fill whole padding buffer but its end after original data.
Remove duplicite padding.
Change-Id: Ia5e312909f68d3cc724c8cbffe1cd903b9102124 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3561 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Thu, 14 Jul 2016 18:33:27 +0000 (20:33 +0200)]
flash/nor: implement protection blocks of different size than erase sector
Originally flash/nor infrastructure assumed protection blocks identical
to erase sectors. This assumption is not valid for many flash types.
Driver code fixed the problem either by increasing sector size to
size of protection block or by defining more protection block than
really existed in device. Both cases had drawbacks.
The change retains compatibility with the old driver.
Updated driver can set protection blocks table independent
of sector table.
Change-Id: I27f6d267528ad9ed9fe0a85f05436a8ec17603a4 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3545 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Tue, 19 Jul 2016 12:27:04 +0000 (14:27 +0200)]
flash Kinetis: dynamic status detection before starting mass_erase
The change prevents starting mass_erase in unstable state of MCU
(RESET/WDOG loop).
mass_erase of secured MCU using manual reset button is supported.
Timeouts are measured by timeval_ms() instead of iteration count.
mass_erase timeout prolonged to 16 seconds because aborting
mass_erase in progress (deasserting reset) leaves the device
in security locked state.
Change-Id: I6605532df56080a54c2a1dfe49094e3db4ce534a Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3551 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Sun, 17 Jul 2016 14:22:47 +0000 (16:22 +0200)]
flash Kinetis: Detect RESET/WDOG loop, fix detection of secured MCU
Kinetis driver checks MDM STAT register to detect secured state of MCU.
Original version often reported a blank device as secured one.
Change #3010 has not fixed all false reports.
After changes in arm_adi_v5 infrastructure secured devices was not detected
at all.
New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and
MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop
are detected reliably.
Detection is run in both kx.cfg and klx.cfg from examine-start event,
not examine-end as before. Event is configured only for non hla adapter.
Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init.
Such frequency is not supported in VLPR CPU mode and with JTAG.
Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3547 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Steven Stallion [Sun, 10 Jul 2016 03:17:14 +0000 (22:17 -0500)]
kinetis: support mass erase on boards without SRST
NXP (nee Freescale) documents the mass erase procedure using the MDM-AP
block in AN4835. Existing support for this feature did not properly
handle boards without SRST. This patch updates the mass_erase command
such that it works correctly on these boards. Additionally, the core is
left in a halted state once complete to prevent reset loops due to the
watchdog as reported by some users.
Since the MDM-AP provides an additional method of halting and resetting
the core that is disconnected from the DAP, additional commands are
provided to manage this state. These commands are particularly helpful
when connecting to a target with an unknown state.
Change-Id: I40f006d5d964befb12b019c5d509988decdd3f91 Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3540 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
at91sam7: do not touch flash banks which belong to other targets
at91sam7_read_part_info() walks throw all flash banks following
current one.
I don't know why it has to do it at all (possibly for multi-bank
devices like SAM7S512), but if there is more than one target in JTAG
chain, this lookup can touch flash bank of another (possibly not
halted) target, which cause probe error and current command
execution abort.
[andreas.fritiofson@gmail.com]: Change to for-loop and reduce
indentation
Change-Id: Ide50e93578786e1250f7a0fd0e3d296247924814 Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2610 Tested-by: jenkins
This change adds JTAG transport in pass-through mode
to the cmsis-dap driver. The patch is originally from
Phillip Pearson <pp@myelin.co.nz>, with additions
by Maksym Hilliaka <oter@frozen-team.com>
Remco Bloemen [Tue, 9 Aug 2016 11:30:12 +0000 (12:30 +0100)]
interface: Add XDS100v3 support.
XDS100v3 is software compatible with the XDS100v2, but has a
different usb pid. This commit adds `xds100v3.cfg` that sources
the v2 one and changes the usb pid.
Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80 Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com>
Reviewed-on: http://openocd.zylin.com/3632 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Peter A. Bigot [Wed, 10 Aug 2016 21:58:07 +0000 (16:58 -0500)]
doc: correct and standardize instructions for disabling TCP servers
The instructions to set the port to zero to disable a service has not
worked for several years: the effect of doing so is to start the service
on a port randomly selected by the bind(2) system call.
Update the documentation to reflect the new standard way of disabling
network services.
Change-Id: Ic5315a80f9956ea195f63e05d30d604a980bbc8f Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3638 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Peter A. Bigot [Wed, 10 Aug 2016 21:54:00 +0000 (16:54 -0500)]
gdb_server: support disabling server
Although the documentation suggested this worked, and it is implemented
for tcl_port and telnet_port, the directive was not recognized for
gdb_port.
Change-Id: I38d95ee879ec3f6d551603b7313749a21e0e498e Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3637 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Andreas Bolsch [Mon, 20 Jun 2016 19:02:29 +0000 (21:02 +0200)]
Flash handling for STM32F76x/77x and F446 added
- added ids for various parts
- rewrite of sector allocation to deal with dual-bank F76x/77x
- single- / dual-bank mode for F76x/77x
- sector protection adapted for F76x/77x in dual-bank mode
- handling of additional option bits (28-31) in FLASH_OPTCR
in options_read and options_write for F42x/43x/469/479/7xx,
options bits 0-1 masked out
- check for sensible value of user_options in options_write
- some #defines clarified, non-needed ones removed
- docs updated (options read, options write)
Change-Id: Ie4db80e60baa7d2663e024ab1f278640b1ce901b Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/3526 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Steven Stallion [Wed, 20 Jul 2016 19:05:12 +0000 (14:05 -0500)]
rtos: remove display_str member
This patch removes the display_str member in the thread_detail struct.
This member was not being used and provides no additional benefit over
the thread_name_str and extra_info_str members. This change is made in
preparation of support for the qXfer:threads:read packet, which will
modernize how thread information is shared with GDB.
Change-Id: I1f8bc6325e6aa790e02ea6caee9d6f44c5fedf36 Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3558 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
jlink: fix jlink regression introduced by ae8cdc commit
1) wrong last bit was shifted out in the end of IRSHIFT/DRSHIFT in
jlink_execute_scan()
2) TDI buffer was not cleared in jlink_tap_init(), results in wrong
data shifted out to the TDI and "Bad value '00000000' captured
during DR or IR scan" error message.
3) sizeof(tdi_buffer) was used in memset() to clean tms buffer. It
is the same as sizeof(tms_buffer), but shoud be fixed to make source
code consistent
Change-Id: I13f26d1c3e88eefc3856fe2b8542fb0ccea6acb1 Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/3394 Tested-by: jenkins Reviewed-by: Harry Zhurov <harry.zhurov@gmail.com> Reviewed-by: Anton Gusev Reviewed-by: Михаил Цивинский <mtsivinsky@gmail.com> Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Thu, 21 Jul 2016 07:27:00 +0000 (09:27 +0200)]
target: check late abort from target in async_algorithm
target_run_flash_async_algorithm() ignored abort from target
(rp set to 0) when raised after all data have been written in fifo.
I could result e.g. in not reported error during flash write.
The change adds rp test after target algorithm has finished.
Change-Id: Iadd93371e4a4602737be10079479285d81ae41b2 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3560 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Andy Pomfret [Tue, 8 Mar 2016 13:52:36 +0000 (13:52 +0000)]
rtos: removed chSysInit from detection of ChibiOS (#121)
Using the presence of the 'chSysInit' symbol for detection of
ChibiOS is dangerous because this symbol may not be available
if link-time optimisation is used.
This patch removes this reliance, so the symbols 'ch' and 'ch_debug'
are the only things required for ChibiOS detection.
If 'ch' is present but 'ch_debug' is not, an info message suggests
that Chibios might be present without its registry being enabled.
This message has been reworded a little to make it slightly more
equivocal because the chances of a false positive message are
increased.
Addresses bug #121, "ChibiOS rtos detection fails with LTO enabled".
Change-Id: I5ef224735c06446751adee010ce75be4f30f0403 Signed-off-by: Andy Pomfret <cooperised@gmail.com>
Reviewed-on: http://openocd.zylin.com/3381 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Andreas Färber [Sun, 22 May 2016 17:12:20 +0000 (19:12 +0200)]
kinetis_ke: Switch to standard build variables
Instead of using ARM_ prefixed variables and an "arm" target,
use CROSS_COMPILE, AS, OBJCOPY. This requires to switch from ?= to =
to avoid the host assembler getting invoked.
This allows to handle kinetis_ke subdirectory like fm4 and xmc1xxx.
Change-Id: I7ea0bf119f6c4716f4d6002794004730af49eef4 Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3505 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tomas Vanek [Sat, 6 Aug 2016 06:28:04 +0000 (08:28 +0200)]
psoc4.cfg: fixed typo in message, add a hint
PSoC4 design prevents reset halt/init with standard/low level
SWD adapter if hw reset line configured. Give user hint
to use 'reset_config none' in such case.
Change-Id: I0ca2c46b8575829b0013fd151f2eb63963d66653 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3617 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Felix Held [Wed, 10 Aug 2016 01:09:02 +0000 (03:09 +0200)]
xilinx-xc7: correct Artix7 15T IDCODE
The IDCODE of Artix7 15T in the UG470 is wrong; Artix7 35T and 15T don't have the same IDCODE.
I've tested this on real hardware.
Change-Id: Iac267dc449c23454dd119126749dbeb8267c18ac Signed-off-by: Felix Held <felix-openocd@felixheld.de>
Reviewed-on: http://openocd.zylin.com/3633 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
adi_v5_jtag: clear sticky overrun condition in WAIT timeout
If WAIT recovery fails (times out), an ABORT command is issued to the
DAP but under some conditions the SSTICKYORUN bit in CTRL/STAT is not
cleared as well, which renders the DP unusable. This happens when
trying to access e.g. the ROM table of powered-down cores, on many
targets.
projects / openocd / log