Andrew F. Davis [Fri, 7 Apr 2017 15:11:19 +0000 (10:11 -0500)]
defconfigs: am335x_hs_evm: Sync HS and non-HS defconfigs
Sync new additions to non-HS defconfig with HS defconfig. Also add SPL
NAND support, this was disabled before due to size constraints, enable
this now at the expense of the less used GPT partition support.
Andrew F. Davis [Fri, 7 Apr 2017 19:29:36 +0000 (14:29 -0500)]
spl: net: Add FIT image support over network boot
FIT support in the net boot case is much like the RAM boot case in that
we load our image to "load_addr" and pass a dummy read function into
"spl_load_simple_fit()". As the load address is no longer hard-coded to
the final execution address, legacy image loading will require load_addr
to be set correctly in the image header.
TI K2E secure devices have to be built with TI_SECURE_DEVICE, FIT, and
FIT_IMAGE_POST_PROCESS enabled. Add a dedicated defconfig for this.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Kconfig: Adds SYS_TEXT_BASE config option for Keystone2
This patch makes SYS_TEXT_BASE a config option for Keystone2
so that it can be used to load u-boot at different addresses
on secure and non-secure Keystone2 devices.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
doc: Updates info on using Keystone2 secure devices
Add a section describing the secure boot image used on
Keystone2 secure devices.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: mach-omap2: Add secure image name common to OMAP and keystone
As K2 can directly boot U-Boot, add u-boot_HS_MLO as the secure image
name for secure K2 devices, for all boot modes other than SPI flash.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: mach-omap2: Enable Kconfig support for K2 HS devices
Like the OMAP54xx, AM43xx, & AM33xx family SoCs, the keystone family
of SoCs also have high security enabled models. Allow K2E devices to
be built with HS Device Type Support.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: mach-keystone: Implements FIT post-processing call for keystone SoCs
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.
The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
image: Fixes build warning with CONFIG_FIT_IMAGE_POST_PROCESS
The function 'board_fit_image_post_process' is defined only when the
config option CONFIG_FIT_IMAGE_POST_PROCESS is enabled. For secure
systems that do not use SPL but do use FIT kernel images, only
CONFIG_FIT_IMAGE_POST_PROCESS will be defined, which will result in an
implicit declaration of function 'board_fit_image_post_process' warning
while building u-boot. Fix this warning.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Andrew F. Davis [Fri, 7 Apr 2017 14:55:20 +0000 (09:55 -0500)]
ti_armv7_common: env: Change FIT image name to match build name
The most common name for a FIT image containing a bootable kernel is
"fitImage", as our builds now use this name also, change this to the
default in our U-Boot environment.
mtd: nand: am335x_spl_bch: Incorporate tWB delay in nand_command function
Various commands to NAND flash results in the NAND flash becoming busy.
For those commands the SoC should wait until the NAND indicates it is
no longer busy before sending further commands. However, there is a delay
between the time the SoC sends its last command and when the NAND flash
sets its Ready/Busy Pin. This delay (tWB) must be respected or the SoC may
falsely assume the flash is ready when in reality it just hasn't had enough
time to indicate that it is busy.
Properly delaying by tWB is already done for nand_command/nand_command_lp
in nand_base.c including the version of it in the Linux kernel. Therefore,
this patch brings the handling of tWB delay inline to nand_base.c
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[trini: Reformat comments slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
Lukasz Majewski [Mon, 27 Mar 2017 08:15:27 +0000 (10:15 +0200)]
ti: clocks: Fix do_enable_clocks() to accept NULL pointers as input parameters
Up till this commit passing NULL as input parameter was allowed, but not
handled properly.
When one passed NULL to one of this function parameters, the code was
executed causing data abort.
However, what is more interesting, the abort was not caught because of code
execution in HYP mode with masked CPSR A bit ("Imprecise Data Abort mask bit).
The TI's AM57xx SoC switch to HYP mode with A bit masked in lowlevel_init.S
due to SMC call. Such operation (by default) is performed in SoC ROM code.
The problem would pop up when one:
- Switch back to SVC mode after disabling LPAE support
- Somebody enables A bit (by executing cpsie a asm instruction)
and then the previously described exception would be caught.
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
common/xyzModem.c: Do not use hard-coded address for debug buffer
Under the plethora of #ifdefs, the xyzModem code hid this pearl:
static char *zm_out = (char *) 0x00380000;
This was only enabled when DEBUG is defined, so it's probably why it
went unnoticed for so long. No idea what platform had memory at that
exact location, but the this approach is extremely hacky.
Use a static buffer instead.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
spl: Kconfig: SPL_MMC_SUPPORT depends on GENERIC_MMC
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
common, kconfig: Fix defaut value of BOOTSTAGE_STASH_SIZE
The default value of BOOTSTAGE_STASH_SIZE should be set to hexadecimal,
but an integer value is set. This fixes the BOOTSTAGE_STASH_SIZE number
from hexadecimal to integer.
Vikas Manocha [Fri, 31 Mar 2017 23:34:39 +0000 (16:34 -0700)]
spl: armv7m: keep ARM v7M in thumb mode while jumping to entry point
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay
in thumb mode.
Similar commit: f99993c10882f7dc8ec35993d5febe59aac01e6a
Author: Matt Porter <mporter@konsulko.com>
Date: Tue May 5 15:00:23 2015 -0400
common/cmd_boot: keep ARM v7M in thumb mode during do_go_exec()
config: am335x_evm: detect BeagleBone Blue using BLA
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing
on robotics with a TI wl1835 wireless module for connectivity.
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
config: am335x_evm: detect Green Wireless using GW1
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.
This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|]
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
config: am335x_evm: detect Black Wireless using BWA
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.
This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
Joakim Tjernlund [Thu, 23 Mar 2017 17:02:41 +0000 (18:02 +0100)]
Remove extra fdt_fixup_ethernet() call
ft_cpu_setup() already calls fdt_fixup_ethernet(), calling it
in image_setup_libfdt() is both redundant and breaks any modifications
done by ft_board_setup(). Restore the old behavior by removing
the call in image_setup_libfdt()
Fixes: 13d06981a982 ("image: Add device tree setup to image library") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Andrew F. Davis [Fri, 10 Mar 2017 21:53:54 +0000 (15:53 -0600)]
ti_armv7_common: env: Use args_mmc in FIT loading path
The env command 'args_fit' does not define a root path, this forces us to
embed the rootfs into the FIT image. FIT images do not need to contain a
rootfs, when they do not the kernel will fall-back to the kernel argument
'root', if this is not defined the kernel will not boot. It is safe to
add this as when we do have the rootfs in FIT this argument is ignored.
As 'loadfit' is only called from the MMC boot path, use 'args_mmc' to
correctly populate 'bootargs'.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
fuz@fuz.su [Tue, 7 Mar 2017 21:53:17 +0000 (22:53 +0100)]
Apparent conflict between CONFIG_BLK and CONFIG_API
Good evening,
I am trying to port FreeBSD to the ASUS Tinker Board, a computer based
on the Rockchip 3288 SoC. FreeBSD's boot loader (named loader(8)) needs
CONFIG_API to be enabled, but trying to build an U-Boot from trunk with
both CONFIG_API and CONFIG_BLK (as required for Rockchip SoC's?) leads
to the following build failure:
$ CROSS_COMPILE=arm-none-eabi- gmake tinker-rk3288_defconfig all
...
CC api/api_storage.o
api/api_storage.c: In function 'dev_read_stor':
api/api_storage.c:334:9: error: 'struct blk_desc' has no member named 'block_read'
if ((dd->block_read) == NULL) {
^~
api/api_storage.c:339:11: error: 'struct blk_desc' has no member named 'block_read'
return dd->block_read(dd, start, len, buf);
^~
api/api_storage.c:340:1: warning: control reaches end of non-void function [-Wreturn-type]
}
^
gmake[2]: *** [scripts/Makefile.build:281: api/api_storage.o] Fehler 1
gmake[1]: *** [Makefile:1229: api] Fehler 2
gmake: *** [Makefile:460: __build_one_by_one] Error 2
I applied the following fix, but the product doesn't boot. Perhaps
that's not a property of the fix though:
Sekhar Nori [Wed, 8 Feb 2017 13:13:59 +0000 (18:43 +0530)]
board: ti: am57xx: enable input on mmc clock
As per the latest pinmux data available for AM572x EVM,
rev A3, input should be enabled on MMC clock lines for
MMC2/2/3 for stable operation.
Further, AM572x TRM, SPRUHZ6, Revised June 2016, in
section 18.4.6.1.1 "Pad Configuration Registers" states
that input should be enabled for MMC 2/3/4 clock lines.
Enable input on MMC1 and MMC3 clock to match the latest
pinmux data. Input is already enabled on MMC2 clock for
BeagleBoard x15. Further, input is already enabled on all
MMCx clocks for other AM57xx boards (AM572x and AM571x
IDK).
Tested with HS and UHS SD card on AM572x EVM Rev A3.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Vignesh R [Wed, 8 Mar 2017 08:28:17 +0000 (13:58 +0530)]
ARM: keystone: Pass SPI MTD partition table via kernel command line
SPI U-Boot image for K2 boards have now exceeded 512K partition
allocated to it and no longer fit the partitions defined in kernel DTS
file. Therefore, pass an updated MTD partition table from U-Boot as
kernel command line arguments to avoid kernel from accidentally
modifying boot loader image that has overflowed to next user partition.
To do is, introduce a common environment file for declaring SPI
partition so that each individual boards need not repeat the same.
Choose appropriate SPI bus from board config file and pass it as command
line argument to kernel.
Philipp Tomsich [Fri, 24 Mar 2017 18:08:55 +0000 (19:08 +0100)]
ARMv8: add GOT sections to the list of sections copied
Recent Linux distributions (e.g. Debian 9) include cross-compilers for
AArch64, but only for the aarch64-linux-gnu triplet only. It can thus
be expected that users will attempt to use the system cross-compiler
(instead of an aarch64-elf variant) to compile U-Boot for their ARMv8
target systems.
One key differences between an aarch64-linux-gnu and an aarch64-elf
compiler are the default settings regarding position-independent: with
the aarch64-linux-gnu compiler, the default will create and use the
global offset table.
This change-set adjusts the list of sections copied on ARMv8 to include
the GOT sections. With this added, the list matches the previous setup
for AArch32 closely.
Note that this is not an 'academic' issue, but was in fact encountered
by our QA during testing of the RK3399-Q7 BSP and resulted in an
early failure of the SPL stage during FDT setup.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
env_mmc: Allow SPL to use any MMC device to load/save the environment
SPL has been restricted to use only dev 0 based on the assumption that only
one MMC device is registered. This is not always the case and many
platforms now register several devices as expected by the spl mmc boot code
For those platform SPL_ENV_SUPPORT is broken if dev is forced to 0.
A word of warning: this commit may break SPL_ENV_SUPPORT on platforms that
do not register the same MMC controllers in SPL and in u-boot (mostly iMX6
based platforms). Fortunately none of those activate SPL_ENV_SUPPORT in
their default configuration.
Florent Jacquet [Thu, 16 Feb 2017 10:46:42 +0000 (11:46 +0100)]
sunxi: Add defconfig for Allwinner A23 EVB
This enables the support for the Allwinner A23 Evaluation Board (EVB),
that already had a device tree (from Linux) but no defconfig.
This board has an AXP223 PMIC, some NAND, Audio out and in plugs, an
accelerometer and light sensor, as well as a USB HSIC hub and a USB
OTG mini-USB connector. It also has a Wifi/BT chip.
Access to the other buses (LCD, MIPI DSI, LVDS, etc) can be done
through dedicated pin headers.
Signed-off-by: Florent Jacquet <florent.jacquet@free-electrons.com> Cc: Jagan Teki <jagan@openedev.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Mon, 20 Mar 2017 14:57:22 +0000 (15:57 +0100)]
sunxi: Add default environment size
On boards that defines ENV_IS_NOWHERE, such as the NES classic, commit 19dbe7d1a3f7 ("common: Move environment choice to Kconfig") broke the build
because of a missing environment size.
Reintroduce a default environment size consistent with what we had before.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Fri, 3 Mar 2017 14:13:30 +0000 (15:13 +0100)]
cmd: nand: Make the NAND options default to NAND_SUNXI
If we depend on the ARCH_SUNXI configuration option, the boards that do not
have NAND support enabled (with the associated options) will not compile
anymore.
Depend on the NAND driver configuration option to make sure that is not the
case.
Reported-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 1 Mar 2017 06:03:34 +0000 (14:03 +0800)]
sunxi: Add boards/sunxi and arch/arm/mach-sunxi to sunxi MAINTAINERS entry
Recently some sunxi related code was moved to arch/arm/mach-sunxi, but
the MAINTAINERS entry was not updated to reflect this. Add this, and
the board level boards/sunxi directory to our entry.
While at it, also update its status, to reflect the current active
maintainership.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message] Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:15 +0000 (18:22 +0100)]
sunxi: Add support for the CHIP Pro
The CHIP Pro is a SoM that features the GR8 SIP, an AXP209, a BT/WiFi chip
and a 512MiB SLC NAND.
This it's an SLC NAND, it doesn't suffer the same drawbacks than found on
the MLC NANDs, and we can enable it right away.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:14 +0000 (18:22 +0100)]
sunxi: Sync GR8 DTS and AXP209 with the kernel
Those DT will be part of 4.10, sync them so we can have our own config.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:13 +0000 (18:22 +0100)]
scripts: sunxi: Build an raw SPL image
Introduce a new sunxi-spl-with-ecc.bin image with already the right header,
ECC, randomizer and padding for the BROM to be able to read it.
It needs to be flashed using a raw access to the NAND so that the
controller doesn't change a thing to it, since we already have all the
right parameters.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Maxime Ripard [Mon, 27 Feb 2017 17:22:12 +0000 (18:22 +0100)]
nand: sunxi: Add options for the SPL NAND configuration
The SPL image needs to be built with a different ECC configuration than the
U-Boot binary.
Add Kconfig options with defaults to provide a value that should work for
anyone, but is still configurable if needs be.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Scott Wood <oss@buserror.net> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:11 +0000 (18:22 +0100)]
sunxi: Add the default mtdids and mtdparts to our env
In order for the user to be able to see and modify them, add those
variables to the default environment.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Hans de Goede [Mon, 27 Feb 2017 17:22:10 +0000 (18:22 +0100)]
sunxi: Enable UBI and NAND support
Enable the NAND and UBI support in the configuration header so that we can
(finally) use it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:09 +0000 (18:22 +0100)]
mtd: sunxi: Change U-Boot offset
The default U-Boot offset for the Allwinner SoCs was set to 32kB.
This was probably to try to maintain some compatibility with the current
image that we build for the MMC where the U-Boot binary is also located at
a 32kB offset.
However, this causes a number of issues. The first one is that it prevents
us from using a backup SPL entirely, which is troublesome in case where the
first would be corrupt (especially on MLC which have a higher number of
bitflips).
We also cannot use the original MMC image on the NAND, because we need to
prepare the SPL image to include the ECCs and randomizer settings, which
reduces the interest of setting it at that particular offset.
It also prevents us from upgrading and flashing the U-Boot and SPLs
independantly, since it's very likely that it will fall in the same erase
block.
Since that default wasn't used by any board, change it for 8MB, which will
be in an erase block of its own, all the erase blocks being multiple of
two. The highest erase block size we encountered is 4MB, which means that
in this particular setup, the first and second erase blocks will be for the
SPL and its backup, and the third for U-Boot.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Boris Brezillon [Mon, 27 Feb 2017 17:22:07 +0000 (18:22 +0100)]
cmd: nand: Expose optional suboptions in Kconfig
Sometime we need to enable advanced suboptions of the nand command set.
Expose these suboptions in Kconfig.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Boris Brezillon [Mon, 27 Feb 2017 17:22:06 +0000 (18:22 +0100)]
cmd: Expose a Kconfig option to enable UBIFS commands
Create a new Kconfig entry to allow CMD_UBIFS selection from Kconfig and
add an hidden LZO option that can be selected by CMD_UBIFS.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Jagan Teki <jagan@openedev.com>
Boris Brezillon [Mon, 27 Feb 2017 17:22:05 +0000 (18:22 +0100)]
mtd: ubi: Select RBTREE option from MTD_UBI Kconfig entry
Expose the RBTREE feature through Kconfig and select this option from the
MTD_UBI option.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Jagan Teki <jagan@openedev.com>
[Rebased on master] Signed-off-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:04 +0000 (18:22 +0100)]
cmd: Add Kconfig option for CMD_MTDPARTS and related options
CMD_MTDPARTS is something the user might or might not want to select, and
might depends on (or be selected by) other options too.
This is even truer for the MTDIDS_DEFAULT and MTDPARTS_DEFAULT options that
might change from one board to another, or from one user to the other,
depending on what it expects and what storage devices are available.
In order to ease that configuration, add those options to Kconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:03 +0000 (18:22 +0100)]
common: Move environment choice to Kconfig
The environment location is something that might change per board
(depending on what storage options are availaible there) or depending on
the user choice (when we have several options).
Instead of hardcoding it in our configuration header, create a Kconfig
choice with the options we use for now, and the symbols that depend on it.
Once done, also remove the irrelevant sunxi defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:02 +0000 (18:22 +0100)]
tools: sunxi: Add spl image builder
This program generates raw SPL images that can be flashed on the NAND with
the ECC and randomizer properly set up.
This has been copied (and tweaked to find the right headers) from the
sunxi-tools (https://github.com/linux-sunxi/sunxi-tools) upstream
repository, commit 1c3a6ca5.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:01 +0000 (18:22 +0100)]
bch: Allow to build for the host
We will need the bch functions in the tool to generate the SPL images for
the Allwinner SoCs.
Do the needed adjustments so that we can use it on the host.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Mon, 27 Feb 2017 17:22:00 +0000 (18:22 +0100)]
nand: sunxi: Fix modulo by zero error
When trying to autodetect the ECC and randomization configurations, the
driver starts with a randomization disabled and no seeds.
In this case, the number of seeds is obviously 0, and the randomize boolean
is set to false.
However, the logic that retrieves the seed for a given page offset will
blindly use the number of seeds, without testing if the randomization is
enabled, basically doing a modulo by 0.
As it turns out, the libgcc in the common toolchain returns 0 here, which
was our expected value in such a case, and why we would not detect it.
However, U-Boot's libgcc will for some reason return from the function
instead, resulting in an error to load the U-Boot binary in the SPL.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Scott Wood <oss@buserror.net> Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master] Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Philipp Tomsich [Wed, 22 Feb 2017 18:46:41 +0000 (19:46 +0100)]
sun8i_emac: configure PHY reset GPIO via DM
This ports the support for configuring a GPIO for resetting the
Ethernet PHY (incl. such details as the reset polarity and
pulse-length) from the Designware driver.
X-AffectedPlatforms: A64-uQ7 Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Tom Rini [Fri, 7 Apr 2017 00:42:18 +0000 (20:42 -0400)]
Remove various unused interrupt related code
With d53ecad92f06 some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi") Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 2 Apr 2017 15:50:32 +0000 (09:50 -0600)]
dm: serial: Allow driver-model serial to be disabled for TPL
Add separate enable/disable controls for driver-model serial. While this
is generally enabled in SPL it may not be in TPL, since serial output can
be obtained with the debug UART with minimal code size.
Simon Glass [Sun, 2 Apr 2017 15:50:30 +0000 (09:50 -0600)]
Makefile: Provide an option to select SPL or TPL
At present we have SPL_ which can be used in Makefiles to select between
normal and SPL CONFIGs like this:
obj-$(CONFIG_$(SPL_)DM) += core/
When TPL is being built, SPL_ has the value 'SPL' which is generally a
good idea since they tend to follow each other. But in extreme situations
we may want to distinugish between SPL and TPL. For example we may not
want to enable CONFIG_DM with TPL.
Add a new SPL_TPL_ variable which is set to either empty (for U-Boot
proper), 'SPL' or 'TPL'. This may prove useful with TPL-specific options.
Simon Glass [Fri, 31 Mar 2017 14:40:37 +0000 (08:40 -0600)]
board_f: Make init_helpers generic
This header file is used by two archs. It could be used by all of them
since it allows the cache to be on during relocation. Move it into a
generic file.
Simon Glass [Fri, 31 Mar 2017 14:40:33 +0000 (08:40 -0600)]
Move dram_init_banksize() to a common header
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.
Simon Glass [Fri, 31 Mar 2017 14:40:27 +0000 (08:40 -0600)]
xtensa: Place relocated U-Boot in the normal place
All archs put U-Boot at the bottom of the relocated region. Xtensa does
not, but perhaps not for any good reason. Adjust it to see if things
still work OK.
Simon Glass [Fri, 31 Mar 2017 14:40:25 +0000 (08:40 -0600)]
board_f: Drop return value from initdram()
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
Simon Glass [Fri, 31 Mar 2017 14:40:24 +0000 (08:40 -0600)]
board_f: Drop board_type parameter from initdram()
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
Simon Glass [Tue, 28 Mar 2017 16:27:32 +0000 (10:27 -0600)]
i2c: Drop CONFIG_SOFT_I2C_MULTI_BUS
This is not used by any board. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Clean up board_f sequence a little
This series tries to remove #ifdefs from the board_f init sequence. It
gets as far as I2C and then we need to discuss whether we can start to
remove the old I2C framework.
I think that ideally each entry in the init sequence should be enabled by
at most one CONFIG, which is in Kconfig and is not arch-specific.
END Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass [Tue, 28 Mar 2017 16:27:30 +0000 (10:27 -0600)]
board_f: x86: Use checkcpu() for CPU init
At present we misuse print_cpuinfo() do so CPU init on x86. This is done
because it is the next available call after the console is enabled. But
several arches use checkcpu() instead. Despite the horrible name (which
we can fix), it seems a better choice.
Adjust the various x86 CPU implementations to move their init code into
checkcpu() and use print_cpuinfo() only for printing CPU info.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
Simon Glass [Tue, 28 Mar 2017 16:27:28 +0000 (10:27 -0600)]
board_f: sandbox: Move sandbox_early_getopt_check() into misc_init_f()
We don't need a special hook for sandbox as one of the later ones will do
just as well. We can print error messages about bad options after we
print the banner. In fact, it seems better.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
projects / u-boot / log