Dirk Behme [Thu, 12 Feb 2009 17:55:41 +0000 (18:55 +0100)]
OMAP3: Beagle: Add board revision detection
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX)
which might need different software handling. For this, GPIO pin 171 (GPIO
module 6, offset 11) can be used to check for board revision. If this pin
is low, we have a rev C board. Else it must be a revision Ax or Bx board.
To handle board differences you can call function beagle_get_revision().
E.g.:
Dirk Behme [Thu, 12 Feb 2009 17:55:40 +0000 (18:55 +0100)]
OMAP3: Overo: Clean up pin mux and GPIO configuration
* Make Overo GPIO114 an input for touchscreen PENDOWN
* Make Overo GPIO144-147 readable
* Make Overo EHCI pinmux match beagle rev c setup
* Adjust pinmux for SMSC911X network chip support
* Remove unnecessary GPIO setup
* Fix merge error in Makefile
Signed-off-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Hugo Villeneuve [Fri, 21 Nov 2008 19:35:56 +0000 (14:35 -0500)]
ARM DaVinci: Add common peripherals and modules enable functions.
Taken all the duplicated code for enabling common modules and apply
software workarounds from the board specific code into common
functions. Also added comments explaining the workarounds
(from TI errata documents) and replaced some numerical bit numbers
with more meaningful defines.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
This driver implements the ECC algorithm described in
the CPU data sheet and uses the OOB layout chosen in
already-released development systems (shipped with a custom-made
u-boot 1.3.1).
Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Cleanup the comment for m68k linux boot argument passing.
This patch clarifies the way m68k passes linux boot argument.
The one gotcha here is that the assembly instruction that
the compiler uses to jump to the kernel is 'jsr' which pushes the
program counter for the instruction after the jsr into the stack pointer.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
Minkyu Kang [Wed, 18 Feb 2009 00:05:52 +0000 (09:05 +0900)]
bootm: Reduce the unnecessary memmove
Although load address and image start address are same address,
bootm command always does memmove.
That is unnecessary memmove and can be taken few milliseconds
(about 500 msec to 1000 msec).
If skip this memmove, we can reduce the boot time.
Matthias Fuchs [Sun, 15 Feb 2009 21:29:15 +0000 (22:29 +0100)]
fpga: Fix Spartan III FPGA booting
This patch does some minor fixing of the Xilinx Spartan III
FPGA boot code:
- Fixed call order of post configuration callback and
success message printing (result of copy-paste?)
- remove obsolete comment
- minor coding style cleanup
Matthias Fuchs [Sun, 15 Feb 2009 21:28:36 +0000 (22:28 +0100)]
fpga: Fix Spartan II FPGA booting
This patch does some minor fixing of the Xilinx Spartan II
FPGA boot code:
- Fixed call order of post configuration callback and
success message printing (result of copy-paste?)
- relocate post configuration callback only when it
is implemented
- remove obsolete comment
- minor coding style cleanup
In the commit 79b51ff8205f0354d5300570614c1d2db499679c ([MIPS] cpu/mips/
Makefile: Split [CS]OBJS onto separate lines), I wrongly deleted a START
line. This patch puts it back.
Micha Kalfon [Wed, 11 Feb 2009 17:50:11 +0000 (19:50 +0200)]
pxa: fixing get_timer to return time in miliseconds.
Fixing the get_timer function to return time in miliseconds instead of
ticks. Also fixed PXA boards to use the conventional value of 1000 for
CONFIG_SYS_HZ.
Heiko Schocher [Thu, 19 Feb 2009 16:23:58 +0000 (17:23 +0100)]
82xx, mgcoge: updates for 2009.03
- activate CS4 for accessing the FPGA
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flashes in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Heiko Schocher [Thu, 19 Feb 2009 16:24:01 +0000 (17:24 +0100)]
8xx, mgsuvd: updates for 2009.03
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flash in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Wolfgang Denk [Thu, 19 Feb 2009 12:53:29 +0000 (13:53 +0100)]
TQM8xxL: make some room in low memory for future needs
THe TQM8xxL use a ahnd-optimized linker script to efficiently use the
small boot sectors in the flash. This patch makes some room in the
first sector to prepare for a size increase of lib_generic/vsprintf.o
by a future patch.
Kim Phillips [Wed, 18 Feb 2009 23:43:59 +0000 (17:43 -0600)]
sata_sil3114: fix compiler warning
judging from other printfs in the same file, it seems ata should be
postpended with the interface number, not the address of the global
port variable. Fixes this for current u-boot-mpc83xx tree:
Configuring for MPC8349ITX board...
sata_sil3114.c: In function 'sata_bus_softreset':
sata_sil3114.c:99: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *'
sata_sil3114.c:108: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *'
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Ron Madrid [Wed, 18 Feb 2009 22:30:44 +0000 (14:30 -0800)]
Create configuration option for restricted ns16550 functions
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error. This option will exclude all functions with exception of
NS16550_putc and NS16550_init. This will be used primarily to save space and
remove unused code from builds in which space is limited.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Kim Phillips [Wed, 18 Feb 2009 22:14:29 +0000 (16:14 -0600)]
mkconfig: include board config.h before asm/config.h
swapping the include order suppresses warnings for board configs
that define their own CONFIG_MAX_MEM_MAPPED:
In file included from /home/r1aaha/git/u-boot/include/config.h:5,
from /home/r1aaha/git/u-boot/include/common.h:35,
from simpc8313.c:26:
/home/r1aaha/git/u-boot/include/configs/SIMPC8313.h:81:1: warning:
"CONFIG_MAX_MEM_MAPPED" redefined
In file included from /home/r1aaha/git/u-boot/include/config.h:4,
from /home/r1aaha/git/u-boot/include/common.h:35,
from simpc8313.c:26:
/home/r1aaha/git/u-boot/include/asm/config.h:28:1: warning: this is
the location of the previous definition
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Ilya Yanok [Thu, 5 Feb 2009 03:08:20 +0000 (04:08 +0100)]
qong: changes to Dave/DENX Qong configuration
1. Changes to the default environment:
- "bootcmd" defined as "run flash_self"
- "saveenv" command removed from "update"
- "uboot" changed to "u-boot" (also in "load")
- "addmtd" variable defined (and added to all boot commands)
2. CONFIG_CMD_JFFS2 defined to enable "mtdparts" command
3. MTDIDS_DEFAULT and MTDPARTS_DEFAULT defined
4. CONFIG_SYS_CBSIZE changed from 256 to 512. That solves the problem
with truncated "bootargs" environment variable.
Petri Lehtinen [Thu, 29 Jan 2009 08:35:40 +0000 (10:35 +0200)]
include/image.h: Ease grepping of image_* functions
Because the functions have been defined using macros, grepping for
their definitions is not possible. This patch adds the real function
names in comments.
Signed-off-by: Petri Lehtinen <petri.lehtinen@inoi.fi> Acked-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 29 Jan 2009 00:08:14 +0000 (19:08 -0500)]
rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENV
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment. So, let's make sure the define is named accordingly.
Rafal Jaworowski [Fri, 23 Jan 2009 12:27:18 +0000 (13:27 +0100)]
API: Improve glue mid-layer of the API demo application.
- Extend ub_dev_read() and ub_dev_recv() so they return the length actually
read, which allows for better control and error handling (this introduces
additional error code API_ESYSC returned by the glue mid-layer).
- Clean up definitions naming and usage.
- Other minor cosmetics.
Note these changes do not touch the API proper, so the interface between
U-Boot and standalone applications remains unchanged.
Rafal Jaworowski [Fri, 23 Jan 2009 12:27:15 +0000 (13:27 +0100)]
API: Use stack pointer as API signature search hint in the glue layer.
De-hardcode range in RAM we search for the API signature. Instead use the stack
pointer as a hint to narrow down the range in which the signature could reside
(it is malloc'ed on the U-Boot heap, and is hoped to remain in some proximity
from stack area). Adjust PowerPC code in API demo to the new scheme.
Andy Fleming [Thu, 30 Oct 2008 21:41:01 +0000 (16:41 -0500)]
Add MMC Framework
Here's a new framework (based roughly off the linux one) for managing
MMC controllers. It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.
This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)
Some of this code was contributed by Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Thu, 30 Oct 2008 21:31:39 +0000 (16:31 -0500)]
Eliminated arch-specific mmc header requirement
The current MMC infrastructure relies on the existence of an
arch-specific header file. This isn't necessary, and a couple
drivers were forced to implement dummy files to meet this requirement.
Instead, we move the stuff in those header files into a more appropriate
place, and eliminate the stubs and the #include of asm/arch/mmc.h
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Mon, 16 Feb 2009 15:40:20 +0000 (09:40 -0600)]
TQM85xx: Fix a couple warnings in TQM8548 build
The ecm variable in sdram.c was being declared for all 8548, but only
used by specific 8548 boards, so we make that variable require those
specific boards, too
The nand code was using an index "i" into a table, and then re-using "i"
to set addresses for each upm. However, then it relied on the old value
of i still being there to enable things. Changed the second "i" to "j"
Signed-off-by: Andy Fleming <afleming@freescale.com>
MPC85xx: TQM8548: workaround for erratum DDR 19 and 20
This patch adds the workaround for erratum DDR20 according to MPC8548
Device Errata document, Rev. 1: "CKE signal may not function correctly
after assertion of HRESET". Furthermore, the bug DDR19 is fixed in
processor version 2.1 and the work-around must be removed.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
MPC85xx: TQM8548: use cache for AG and BE variants
This patch makes accesses to the system memory cachable by removing the
caching-inhibited and guarded flags from the relevant TLB entries for
the TQM8548_BE and TQM8548_AG modules. FYI, the Freescale MPC85* boards
are configured similarly.
This results in a big averall performace improvement. TFTP downloads,
NAND Flash accesses, kernel boots, etc. are much faster.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
MPC85xx: TQM8548: add support for the TQM8548_AG module
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
MPC85xx: TQM8548: add support for the TQM8548_BE module
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
MPC85xx: TQM85xx: make standard PCI/PCI-X configurable
The TQM8548_AG module does not have the standard PCI/PCI-X interface
connected but just the PCI Express interface . So far it was not
possible to disable it without disabling the complete PCI interface
(CONFIG_PCI) including PCI Express.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
MPC85xx: TQM85xx: fix flash protection for boot loader
As the reset vector is located at 0xfffffffc, all flash sectors from the
beginning of the U-Boot binary to 0xffffffff must be protected. On the
TQM8548-AG having small sectors at the end of the flash it happened that
the last two sector were not protected and an "erase all" left an
un-bootable system behind:
Bank # 2: CFI conformant FLASH (32 x 16) Size: 32 MB in 270 Sectors
AMD Standard command set, Manufacturer ID: 0xEC, Device ID: 0x257E
Erase timeout: 8192 ms, write timeout: 1 ms
Peter Tyser [Fri, 6 Feb 2009 20:30:40 +0000 (14:30 -0600)]
86xx: Update CPU info output on bootup
- Update style of 86xx CPU information on boot to more closely
match 85xx boards
- Fix detection of 8641/8641D
- Use strmhz() to display frequencies
- Display L1 information
- Display L2 cache size
- Fixed CPU/SVR version output
Peter Tyser [Thu, 5 Feb 2009 17:25:25 +0000 (11:25 -0600)]
86xx: Reset update
Update the 86xx reset sequence to try executing a board-specific reset
function. If the board-specific reset is not implemented or does not
succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard
reset procedure than the previous method and allows all board
peripherals to be reset if needed.
Kumar Gala [Wed, 11 Feb 2009 05:53:40 +0000 (23:53 -0600)]
fsl-ddr: Allow system to boot if we have more than 4G of memory
Previously if we >=4G of memory and !CONFIG_PHYS_64BIT we'd report
an error and hang. Instead of doing that since DDR is mapped in the
lowest priority LAWs we setup the DDR controller and the max amount
of memory we report back is what we can map (CONFIG_MAX_MEM_MAPPED)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Kumar Gala [Tue, 10 Feb 2009 23:36:15 +0000 (17:36 -0600)]
85xx: print boot header info to distinquish 36-bit addr map on MPC8572 DS
Added some info that is printed out when we boot to distiquish if we
built MPC8572DS_config vs MPC8572DS_36BIT_config since they have
different address maps.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 10 Feb 2009 04:03:04 +0000 (22:03 -0600)]
85xx: Fix bug in device tree setup in 36-bit physical confg
In the 36-bit physical config for MPC8572DS when need the start address
of memory and it size to be kept in phys_*_t instead of a ulong since
we support >4G of memory in the config and ulong cant represent that.
Otherwise we end up seeing the memory node in the device tree reporting
back we have memory starting @ 0 and of size 0.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 10 Feb 2009 04:03:05 +0000 (22:03 -0600)]
85xx: Fix address map for 36-bit config of MPC8572DS
When we introduced the 36-bit config of the MPC8572DS board we had the
wrong PCI MEM bus address map. Additionally, the change to the address
map exposes a small issue in our dummy read on the ULI bus. We need
to use the new mapping functions to handle that read properly in the
36-bit config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 6 Feb 2009 15:56:35 +0000 (09:56 -0600)]
85xx: Fix how we map DDR memory
Previously we only allowed power-of-two memory sizes and didnt
handle >2G of memory. Now we will map up to CONFIG_MAX_MEM_MAPPED
and should properly handle any size that we can make in the TLBs
we have available to us
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 6 Feb 2009 15:56:34 +0000 (09:56 -0600)]
fsl-ddr: ignore memctl_intlv_ctl setting if only one DDR controller
If we only have one controller we can completely ignore how
memctl_intlv_ctl is set. Otherwise other levels of code get confused
and think we have twice as much memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Abraham, Thomas [Tue, 28 Oct 2008 11:21:31 +0000 (16:51 +0530)]
USB: Remove LUN number from CDB
The LUN number is not part of the Command Descriptor Block (CDB) for scsi inquiry, request sense, test unit ready, read capacity and read10 commands. This patch removes the LUN number information from the CDB.
Signed-off-by: Thomas Abraham <t-abraham@ti.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
V3: Fixed line-wrap problem due to user error in mail!
Added usb_configured() checks in usbtty_puts() and usbtty_putc() to get around a hang
when usb is not connected and the user has set up multi-io (setenv stdout serial,usbtty etc).
Got rid of redundant __attribute__((packed)) directives that were causing warnings from gcc.
i.MX31: Start the I2C clock on driver initialisation
i.MX31 powers on with most clocks running, so, after a power on this explicit
clock start up is not required. However, as Linux boots it disables most clocks
to save power. This includes the I2C clock. If we then soft reboot from Linux
the I2C clock stays off. This breaks the phycore, which has its environment in
I2C EEPROM. Fix the problem by explicitly starting the clock in I2C driver
initialisation routine.
Carolyn Smith [Thu, 12 Feb 2009 05:13:44 +0000 (06:13 +0100)]
ppc4xx: Fix initialization of the SDRAM_CODT register
This fixes the initialization of the SDRAM_CODT register in the ppc4xx DDR2
initialization code. It also removes use of the SDRAM_CODT_FEEDBACK_RCV_SINGLE_END
and SDRAM_CODT_FEEDBACK_DRV_SINGLE_END #define's since they are reserved bits.
Signed-off-by: Carolyn Smith <carolyn.smith@tektronix.com> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot / log