Masahiro Yamada [Thu, 27 Oct 2016 14:47:07 +0000 (23:47 +0900)]
ARM: uniphier: rework existing DDR PHY code to reuse for LD11 SoC
The DDR PHY register view of LD11 is slightly different from that
of LD4/Pro4/sLD8, but it will be possible to share the register
macros (and I want to re-use as much code as possible). Change
the code in the more flexible form.
Masahiro Yamada [Thu, 27 Oct 2016 14:47:06 +0000 (23:47 +0900)]
ARM: uniphier: do not run harmful code for USB boot mode of LD11 ES3
The USB boot without the stand-by MPU is available on ES3 or later
of LD11 SoC, but the code in this if-conditional block must not be
run when booting from USB. Check if the boot device is USB, and
skip the code in the case.
Masahiro Yamada [Thu, 27 Oct 2016 14:47:05 +0000 (23:47 +0900)]
ARM: uniphier: enable clocks to MIO/STDMAC on LD11 if USB is enabled
At the moment, the clk driver is not clever enough to automatically
enable parent clocks like Linux. Enable the STDMAC clock explicitly
if USB is enabled.
Wenyou Yang [Fri, 28 Oct 2016 06:17:49 +0000 (14:17 +0800)]
dm: at91: Add driver model support for the spi driver
Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com>
Wenyou Yang [Mon, 17 Oct 2016 01:55:26 +0000 (09:55 +0800)]
board: sama5d2_xplained: Enable an early debug UART
Enable an early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wenyou Yang [Mon, 17 Oct 2016 01:55:24 +0000 (09:55 +0800)]
board: sama5d2_xplained: Clean up code
Since the introduction of pinctrl and clk driver, and the dts file,
remove unneeded the pin configurations and the clock enabling code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wenyou Yang [Tue, 27 Sep 2016 03:00:29 +0000 (11:00 +0800)]
clk: at91: Improve the clock implementation
For the peripheral clock, provide the clock ops for the clock
provider, such as spi0_clk. The .of_xlate is to get the clk->id,
the .enable is to enable the spi0 peripheral clock, the .get_rate
is to get the clock frequency.
The driver for periph32ck node is responsible for recursively
binding its children as clk devices, not provide the clock ops.
So do the generated clock and system clock.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Stephen Warren <swarren@nvidia.com>
Wenyou Yang [Tue, 27 Sep 2016 03:00:28 +0000 (11:00 +0800)]
clk: clk-uclass: Assign clk->dev before call .of_xlate
In order to make clk->dev available in ops->of_xlate() to get the
clock ID from the 'reg' property of the clock node, assign the
clk->dev before calling ops->of_xlate().
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Sun, 18 Sep 2016 07:37:47 +0000 (15:37 +0800)]
ARM: at91/dt: sama5d2: Fix the warning from dtc
Fix the warning from dtc like,
---8<----
Warning (unit_address_vs_reg): Node /ahb/apb/pmc@f0014000/periph64ck/sdmmc0_hclk has a reg or ranges property, but no unit name
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Stephen Warren <swarren@nvidia.com>
Wenyou Yang [Tue, 13 Sep 2016 02:25:55 +0000 (10:25 +0800)]
clk: at91: Fix at91-pmc and at91-sckc's class ID
The at91-pmc and at91-sckc aren't the clock providers, change their
class ID from UCLASS_CLK to UCLASS_SIMPLE_BUS, they also don't
need to bind the child nodes explicitly, the .post_bind callback
of simple_bus uclass will do it for them.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Heiko Schocher [Wed, 17 Aug 2016 07:13:25 +0000 (09:13 +0200)]
arm, at91: add icache support
add at least icache support for at91 based boards.
This speeds up NOR flash access on an at91sam9g15
based board from 15.2 seconds reading 8 MiB from
a SPI NOR flash to 5.7 seconds.
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Bin Meng [Mon, 17 Oct 2016 06:35:18 +0000 (23:35 -0700)]
pci: Move CONFIG_PCI_PNP to Kconfig
Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes] Signed-off-by: Tom Rini <trini@konsulko.com>
Jaehoon Chung [Thu, 13 Oct 2016 01:33:06 +0000 (10:33 +0900)]
mmc: sdhci: fix the "misaligned operation at range" for cache
This pathc is fixed the below thing.
If misaligned the cache range, Just flush to CACHLINE_SIZE.
"CACHE: Misaligned operation at range [7ae55b00, 7ae55b08]"
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 55C
Reset cause: WDOG
Model: Engicam i.CoreM6 DualLite/Solo Starter Kit
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Scott Wood <oss@buserror.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:24 +0000 (18:00 +0530)]
arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:19 +0000 (18:00 +0530)]
arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage 6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800a787
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------
CPU: Freescale i.MX6Q rev1.2 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:10 +0000 (18:00 +0530)]
config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
- Add DEFAULT_FDT_FILE kconfig entry
- Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs
Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Marek Vasut [Thu, 20 Oct 2016 14:48:28 +0000 (16:48 +0200)]
i2c: designware: Avoid overwriting the cmd_data register
Make sure the driver writes the cmd_data register only once per
read transfer instead of doing so potentially repeatedly.
In case the read transfer didn't finish quickly enough, the loop
in the driver code would spin fast enough to write the same value
into the cmd_data register again before re-checking whether the
transfer completed, which would cause another spurious read transfer
on the bus.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Heiko Schocher <hs@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Chin Liang See <clsee@altera.com>
Tom Rini [Thu, 20 Oct 2016 15:26:40 +0000 (11:26 -0400)]
travis-ci: Add test.py for various qemu platforms
- Add a PPA for a more recent qemu (required for PowerPC to work)
- Add tests to run test.py for various QEMU platforms. This relies on
swarren's uboot-test-hooks repository to provide the abstractions.
Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 20 Oct 2016 15:24:52 +0000 (11:24 -0400)]
travis-ci: Drop 'TEST_CMD'
We don't need to use TEST_CMD in order to run tests. We need a BUILDMAN
and TOOLCHAIN variable to avoid having to duplicate logic or write some
wrapper function. But this makes the tests harder as we add more
complex examples.
Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 20 Oct 2016 15:08:26 +0000 (11:08 -0400)]
travis-ci: Update toolchain and buildman usage
- Drop the 'cache' line, travis-ci says to not cache apt packages (and
does not).
- Get the Ubuntu provided toolchain for ARM and PowerPC.
- Add more toolchain options that buildman can fetch.
Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 20 Oct 2016 15:05:57 +0000 (11:05 -0400)]
travis-ci: Do not make buildman warnings fatal
We currently will always see a number of warnings due to device tree
issues. These (and other warnings) should not make the build be marked
as failure so catch exit status 129 specifically and return 0 in that
case.
Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Wed, 19 Oct 2016 05:39:54 +0000 (14:39 +0900)]
tools: moveconfig: support wildcards in --defconfigs file
Supporting shell-style wildcards for the --defconfigs option will be
useful to run the moveconfig tool against a specific platform. For
example, "uniphier*" in the file passed by --defconfigs option will
be expanded to defconfig files that start with "uniphier". This is
easier than listing out all defconfig files you are interested in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Masahiro Yamada [Mon, 17 Oct 2016 11:43:01 +0000 (20:43 +0900)]
Fix codying style broken by recent libfdt sync
Commit b02e4044ff8e ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
Nicolae Rosia [Thu, 13 Oct 2016 10:47:53 +0000 (13:47 +0300)]
power: twl6030: fix code refactoring
Commit a85362fb3e1fc7833723accddbbae431091d06b8 refactored the code
but the register read ended up in the wrong if branch.
Currently, the else branch checks a variable which is always 0.
Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Stefan Brüns [Sun, 9 Oct 2016 18:15:27 +0000 (20:15 +0200)]
ext4: Fix handling of direntlen in unlink_filename
The direntlen checks were quite bogus, i.e. the loop termination used
"len + offset == blocksize" (exact match only), and checked for a
direntlen less than 0. The latter can never happen as the len is
unsigned, this has been reported by Coverity, CID 153384.
Use the same code as in search_dir for directory traversal. This code
has the correct checks for direntlen >= sizeof(struct dirent), and
offset < blocksize.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Reported-by: Coverity (CID: 153383, 153384) Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Peng Fan [Tue, 11 Oct 2016 06:29:11 +0000 (14:29 +0800)]
imx: mx7: Add plugin support
Add mx7_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Peng Fan [Tue, 11 Oct 2016 06:29:10 +0000 (14:29 +0800)]
imx: mx6: Add plugin support
Add mx6_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Peng Fan [Tue, 11 Oct 2016 06:29:09 +0000 (14:29 +0800)]
tools: imximage: add plugin support
Add plugin support for imximage.
Define CONFIG_USE_IMXIMG_PLUGIN in defconfig to enable using plugin.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Ye Li <ye.li@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Tue, 18 Oct 2016 02:12:51 +0000 (20:12 -0600)]
Convert CONFIG_VIDEO_SW_CURSOR to Kconfig
This converts the following to Kconfig:
CONFIG_VIDEO_SW_CURSOR
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-convert, find all the cases where this is off] Signed-off-by: Tom Rini <trini@konsulko.com>
projects / u-boot / log