Dave Liu [Thu, 23 Oct 2008 13:18:53 +0000 (21:18 +0800)]
85xx: Fix the incorrect register used for DDR erratum1
The 8572 DDR erratum1:
DDR controller may enter an illegal state when operating
in 32-bit bus mode with 4-beat bursts.
Description:
When operating with a 32-bit bus, it is recommended that
DDR_SDRAM_CFG[8_BE] is cleared when DDR2 memories are used.
This forces the DDR controller to use 4-beat bursts when
communicating to the DRAMs. However, an issue exists that
could lead to data corruption when the DDR controller is
in 32-bit bus mode while using 4-beat bursts.
Projected Impact:
If the DDR controller is operating in 32-bit bus mode with
4-beat bursts, then the controller may enter into a bad state.
All subsequent reads from memory is corrupted.
Four-beat bursts with a 32-bit bus only is used with DDR2 memories.
Therefore, this erratum does not affect DDR3 mode.
Work Arounds:
To work around this issue, software must set DEBUG_1[31] in
DDR memory mapped space (CCSRBAR offset + 0x2f00 for DDR_1
and CCSRBAR offset + 0x6f00 for DDR_2).
Currenlty, the code is using incorrect register DDR_SDRAM_CFG_2
as condition, but it should be DDR_SDRAM_CFG register.
Anton Vorontsov [Wed, 8 Oct 2008 16:52:54 +0000 (20:52 +0400)]
mpc83xx: add ELBC NAND support for the MPC837XEMDS boards
Though NAND chip is replaceable on the MPC837XE-MDS boards, the
current settings don't work with the default chip on the board.
Nevertheless Freescale's U-Boot sets the option register correctly,
so I just dumped the register from the working u-boot. My guess is
that the old settings were applicable for some pilot boards, not
found in the production.
This patch also enables FSL ELBC driver so that we could access
the NAND storage in the u-boot.
The NAND support costs about 45KB, so the u-boot no longer fits
into two 128KB NOR flash sectors, thus we also have to adjust
environment location: add another 128KB to the monitor length.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
It is due to hardware design and logic defect, that is the
I/O[0:7] of NAND chip is connected to LAD[7:0], so when
the NAND chip connected to nLCS3, you have to set up the
OR3[BCTLD] = '1' for normal operation, otherwise it will have
bus contention due to the pin 48/25 of U60 is enabled.
Setup the OR3[BCTLD] = '1' , that meaning the LBCTL is not
asserted upon access to the NAND chip, keep the default state.
Acked-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Thu, 2 Oct 2008 15:17:33 +0000 (19:17 +0400)]
mpc83xx: fix PCI scan hang on the standalone MPC837xE-MDS boards
The MPC837xE-MDS board's CPLD can auto-detect if the board is on the PIB,
standalone or acting as a PCI agent. User's Guide says:
- When the CPLD recognizes its location on the PIB it automatically
configures RCW to the PCI Host.
- If the CPLD fails to recognize its location then it is automatically
configured as an Agent and the PCI is configured to an external arbiter.
This sounds good. Though in the standalone setup the CPLD sets PCI_HOST
flag (it's ok, we can't act as PCI agents since we receive CLKIN, not
PCICLK), but the CPLD doesn't set the ARBITER_ENABLE flag, and without
any arbiter bad things will happen (here the board hangs during any config
space reads).
In this situation we must disable the PCI. And in case of anybody really
want to use an external arbiter, we provide "pci_external_aribter"
environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Wed, 10 Sep 2008 14:12:37 +0000 (18:12 +0400)]
mpc83xx: mpc8360emds: rework LBC SDRAM setup
Currently 64M of LBC SDRAM are mapped at 0xF0000000 which makes
it difficult to use (b/c then the memory is discontinuous and
there is quite big memory hole between the DDR/SDRAM regions).
This patch reworks LBC SDRAM setup so that now we dynamically
place the LBC SDRAM near the DDR (or at 0x0 if there isn't any
DDR memory).
With this patch we're able to:
- Boot without external DDR memory;
- Use most "DDR + SDRAM" setups without need to support for
sparse/discontinuous memory model in the software.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Tue, 21 Oct 2008 09:23:56 +0000 (11:23 +0200)]
FDT: don't use private kernel header files
On some systems (for example Fedora Core 4) U-Boot builds with the
following wanrings only:
...
In file included from /home/wd/git/u-boot/include/libfdt_env.h:33,
from fdt.c:51:
/usr/include/asm/byteorder.h:6:2: warning: #warning using private kernel header; include <endian.h> instead!
Stefan Roese [Mon, 13 Oct 2008 08:45:14 +0000 (10:45 +0200)]
ppc4xx: Correctly setup ranges property in ebc node
Previously only the NOR flash mapping was written into the ranges
property of the ebc node. This patch now writes all enabled chip
select areas into the ranges property.
Adam Graham [Wed, 8 Oct 2008 17:13:19 +0000 (10:13 -0700)]
ppc4xx: Add routine to retrieve CPU number
Provide a weak defined routine to retrieve the CPU number for
reference boards that have multiple CPU's. Default behavior
is the existing single CPU print output. Reference boards with
multiple CPU's need to provide a board specific routine.
See board/amcc/arches/arches.c for an example.
Signed-off-by: Adam Graham <agraham@amcc.com> Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
Adam Graham [Wed, 8 Oct 2008 17:13:14 +0000 (10:13 -0700)]
ppc4xx: Add static support for 44x IBM SDRAM Controller
This patch add the capability to configure a PPC440 based IBM SDRAM
Controller with static, compiled-in, values. PPC440 memory subsystem
includes a Memory Queue core.
Signed-off-by: Adam Graham <agraham@amcc.com> Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
Adam Graham [Wed, 8 Oct 2008 17:12:53 +0000 (10:12 -0700)]
ppc4xx: Add AMCC Arches board support (dual 460GT)
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Adam Graham <agraham@amcc.com> Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sun, 19 Oct 2008 19:54:30 +0000 (21:54 +0200)]
TQM8260: environment in flash instead EEPROM, baudrate 115k
Several customers have reported problems with the environment in
EEPROM, including corrupted content after board reset. Probably the
code to prevent I2C Enge Conditions is not working sufficiently.
We move the environment to flash now, which allows to have a backup
copy plus gives much faster boot times.
Also, change the default console initialization to 115200 bps as used
on most other boards.
Timur Tabi [Mon, 20 Oct 2008 20:16:47 +0000 (15:16 -0500)]
85xx: properly document MPC85xx_PORDEVSR2_SEC_CFG
Commit f7d190b1 corrected the value of MPC85xx_PORDEVSR2_SEC_CFG, but forgot
to add a comment that the correct value disagrees with the 8544 reference
manual. The changelog for that commit is also wrong, as it says "bit 28"
when it should be "bit 24".
Liu Yu [Fri, 10 Oct 2008 03:40:58 +0000 (11:40 +0800)]
Make pixis_set_sgmii more general to support MPC85xx boards.
The pixis sgmii command depend on the FPGA support on the board, some 85xx
boards support SGMII riser card but did not support this command, define
CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command.
Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits
are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and
PIXIS_VCFGEN1_MASK in header file for both boards.
Ed Swarthout [Thu, 9 Oct 2008 05:29:27 +0000 (00:29 -0500)]
mpc8572 additional end-point mode
mpc8572 supports all pcie controllers as end-points with cfg_host_agent=0.
Include host_agent == 0 decode for end-point determination.
This is not needed for the ds reference board since pcie3 will be a host
in order to connect to the uli chip. Include it here as a reference for
other mpc8572 boards.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Andy Fleming [Tue, 7 Oct 2008 13:09:50 +0000 (08:09 -0500)]
Have u-boot pass stashing parameters into device tree
Some cores don't support ethernet stashing at all, and some
instances have errata. Adds 3 properties to gianfar nodes
which support stashing. For now, just add this support to
85xx SoCs.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Haiying Wang [Fri, 3 Oct 2008 16:37:41 +0000 (12:37 -0400)]
Add ddr interleaving suppport for MPC8572DS board
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.
Haiying Wang [Fri, 3 Oct 2008 16:37:10 +0000 (12:37 -0400)]
Check DDR interleaving mode
* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and
ba_intlv_ctl.
* Print DDR interleaving mode information
* Add doc/README.fsl-ddr to describe the interleaving setting
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Haiying Wang [Fri, 3 Oct 2008 16:36:55 +0000 (12:36 -0400)]
Pass dimm parameters to populate populate controller options
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Haiying Wang [Fri, 3 Oct 2008 16:36:39 +0000 (12:36 -0400)]
Make DDR interleaving mode work correctly
Fix some bugs:
1. Correctly set intlv_ctl in cs_config.
2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled.
3. Set base_address and total memory for each ddr controller in memory
controller interleaving mode.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Kumar Gala [Mon, 22 Sep 2008 19:11:11 +0000 (14:11 -0500)]
85xx: Improve flash remapping on MPC8572DS & MPC8536DS
Changing the flash from cacheable to cache-inhibited was taking a significant
amount of time due to the fact that we were iterating over the full 256M of
flash. Instead we can just flush the L1 d-cache and invalidate the i-cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 22 Sep 2008 19:11:10 +0000 (14:11 -0500)]
85xx: Export invalidate_{i,d}cache and add flush_dcache
Added the ability for C code to invalidate the i/d-cache's and
to flush the d-cache. This allows us to more efficient change mappings
from cache-able to cache-inhibited.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 17 Oct 2008 02:52:08 +0000 (21:52 -0500)]
Added arch_lmb_reserve to allow arch specific memory regions protection
Each architecture has different ways of determine what regions of memory
might not be valid to get overwritten when we boot. This provides a
hook to allow them to reserve any regions they care about. Currently
only ppc, m68k and sparc need/use this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 23 Sep 2008 15:05:02 +0000 (10:05 -0500)]
Expose command table search for sub-commands
Sub-command can benefit from using the same table and search functions
that top level commands have. Expose this functionality by refactoring
find_cmd() and introducing find_cmd_tbl() that sub-command processing
can call.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Heiko Schocher [Wed, 15 Oct 2008 07:40:28 +0000 (09:40 +0200)]
hush: add showvar command for hush shell.
This new command shows the local variables defined in
the hush shell:
=> help showvar
showvar
- print values of all hushshell variables
showvar name ...
- print value of hushshell variable 'name'
Also make the set_local_var() and unset_local_var ()
no longer static, so it is possible to define local
hush shell variables at boot time. If CONFIG_HUSH_INIT_VAR
is defined, u-boot calls hush_init_var (), where
boardspecific code can define local hush shell
variables at boottime.
Heiko Schocher [Wed, 15 Oct 2008 07:39:08 +0000 (09:39 +0200)]
mgcoge, mgsuvd: add board specific I2C deblocking mechanism.
As documented in doc/I2C_Edge_Conditions, adding a
board specific deblocking mechanism via CFG_I2C_INIT_BOARD
for the mgcoge and mgsuvd board.
This code was originally written by Keymile in association
with Anatech and Atmel in 1998. The Code toggels the SCL
until the SCA line goes to HIGH (max. 16 times).
And after this, a start condition is sent.
This is another approach to deblock the I2C Bus. The
soft I2C driver actually sends 9 clocks with SDA High,
and then a stop at the end, to deblock the I2C Bus.
Maybe we should use the approach from Keymile as
the new standard?
Heiko Schocher [Wed, 15 Oct 2008 07:35:26 +0000 (09:35 +0200)]
soft_i2c: prevent compiler warnings if driver does not use CPU Pins.
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:
soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Heiko Schocher [Wed, 15 Oct 2008 07:33:30 +0000 (09:33 +0200)]
I2C: add new command i2c reset.
If I2C Bus is blocked (see doc/I2C_Edge_Conditions),
it is not possible to get out of this, until the
complete Hardware gets a reset. This new commando
calls again i2c_init (and that calls i2c_init_board
if defined), which will deblock the I2C Bus.
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
Dirk Eibach [Wed, 8 Oct 2008 11:44:27 +0000 (13:44 +0200)]
hwmon: Add LM63 support
This patch adds support for the National LM63 temperature
sensor with integrated fan control. It's used on the GDSys
Neo board (405EP) which will be submitted later.
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Acked-by: Stefan Roese <sr@denx.de>
The auto-update feature allows to automatically download software updates
from a TFTP server and store them in Flash memory during boot. Updates are
contained in a FIT file and protected with SHA-1 checksum.
More detailed description can be found in doc/README.update.
flash: factor out adjusting of Flash address to the end of sector
The upcoming automatic update feature needs the ability to adjust an
address within Flash to the end of its respective sector. Factor out
this functionality to a new function flash_sect_roundb().
There are two aspects of a TFTP transfer involving timeouts:
1. timeout waiting for initial server reply after sending RRQ
2. timeouts while transferring actual data from the server
Since the upcoming auto-update feature attempts a TFTP download during each
boot, it is undesirable to have a long delay when the TFTP server is not
available. Thus, this commit makes the server timeout (1.) configurable by two
global variables:
TftpRRQTimeoutMSecs
TftpRRQTimeoutCountMax
TftpRRQTimeoutMSecs overrides default timeout when trying to connect to a TFTP
server, TftpRRQTimeoutCountMax overrides default number of connection retries.
The total delay when trying to download a file from a non-existing TFTP server
is TftpRRQTimeoutMSecs x TftpRRQTimeoutCountMax milliseconds.
Timeouts during file transfers (2.) are unaffected.
net: express the first argument to NetSetTimeout() in milliseconds
Enforce millisecond semantics of the first argument to NetSetTimeout() --
the change is transparent for well-behaving boards (CFG_HZ == 1000 and
get_timer() countiing in milliseconds).
Rationale for this patch is to enable millisecond granularity for
network-related timeouts, which is needed for the upcoming automatic
software update feature.
Summary of changes:
- do not scale the first argument to NetSetTimeout() by CFG_HZ
- change timeout values used in the networking code to milliseconds
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Haiying Wang [Wed, 24 Sep 2008 16:42:12 +0000 (11:42 -0500)]
Change UEC PHY interface to RGMII on MPC8568MDS
Change UEC phy interface from GMII to RGMII on MPC8568MDS board
Because on MPC8568MDS, GMII interface is only recommended for 1000Mbps speed,
but RGMII interface can work at 10/100/1000Mbps, and RGMII interface works more stable.
Now both UEC1 and UEC2 can work properly under u-boot.
It is also in consistent with the kernel setting for 8568 UEC phy interface.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Lepcha Suchit [Thu, 16 Oct 2008 18:38:00 +0000 (13:38 -0500)]
83xx NAND boot: wait for LTESR[CC]
At least some revisions of the 8313, and possibly other chips, do not
wait for all pages of the initial 4K NAND region to be loaded before
beginning execution; thus, we wait for it before branching out of the
first NAND page.
This fixes warm reset problems when booting from NAND on 8313erdb.
Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
Yuri Tikhonov [Fri, 17 Oct 2008 10:54:18 +0000 (12:54 +0200)]
ppc4xx: PPC44x MQ initialization
Set the MQ Read Passing & MCIF Cycle limits to the recommended by AMCC
values. This fixes the occasional 440SPe hard locking issues when the 440SPe's
dedicated DMA engines are used (e.g. by the h/w accelerated RAID driver).
Previously the appropriate initialization had been made in Linux, by the
ppc440spe ADMA driver, which is wrong because modifying the MQ configuration
registers after normal operation has begun is not supported and could
have unpredictable results.
Comment from Stefan: This patch doesn't change the resulting value of the
MQ registers. It explicitly sets/clears all bits to the desired state which
better documents the resulting register value instead of relying on pre-set
default values.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 17 Oct 2008 10:51:46 +0000 (12:51 +0200)]
ppc4xx: PPC44x MQ initialization
Set the MQ Read Passing & MCIF Cycle limits to the recommended by AMCC
values. This fixes the occasional 440SPe hard locking issues when the 440SPe's
dedicated DMA engines are used (e.g. by the h/w accelerated RAID driver).
Previously the appropriate initialization had been made in Linux, by the
ppc440spe ADMA driver, which is wrong because modifying the MQ configuration
registers after normal operation has begun is not supported and could
have unpredictable results.
Comment from Stefan: This patch doesn't change the resulting value of the
MQ registers. It explicitly sets/clears all bits to the desired state which
better documents the resulting register value instead of relying on pre-set
default values.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Stefan Roese <sr@denx.de>
Kumar Gala [Fri, 17 Oct 2008 02:58:50 +0000 (21:58 -0500)]
85xx: Using proper I2C source clock divider for MPC8544
The MPC8544 RM incorrect shows the SEC_CFG bit in PORDEVSR2 as being
bit 26, instead it should be bit 28. This caused in incorrect
interpretation of the i2c_clk which is the same as the SEC clk on
MPC8544. The SEC clk is controlled by cfg_sec_freq that is reported
in PORDEVSR2.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The fix introduced by this patch is not correct. The problem is
that the documentation is not correct for the MPC8544 with regards
to which bit in PORDEVSR2 is for the SEC_CFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jason Jin [Wed, 15 Oct 2008 02:40:24 +0000 (10:40 +0800)]
Fix the function conflict in x86emu when DEBUG is on
The function parse_line() in common/main.c was exposed globally by commit 6636b62a6efc7f14e6e788788631ae7a7fca4537, Result in conflict with the same
name funciton in drivers/bios_emulator/x86emu/debug.c when define the DEBUG.
This patch fix this by renaming the function in the debug.c file.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
projects / u-boot / log