Bharat Bhushan [Wed, 22 Mar 2017 06:36:27 +0000 (12:06 +0530)]
arvm8: pcie-layerscape: Define stream-ids for Layerscape Chassis-2
Layerscape Chassis-2 have PCIe device, some platform devices and
DPAA1 devices which will use stream-ids for iommu level isolation
as they are behind SMMU.
This patch defines the stream-ids for Chassis-2 devices. DPAA1 is
reserved for future use.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Bharat Bhushan [Wed, 22 Mar 2017 06:36:26 +0000 (12:06 +0530)]
armv8: fsl-lsch3: Rewrite comment for stream IDs
LS2080a, LS1088a and LS2088a SOCs are based on Chassis-3 and shared
same stream-id partitioning. This patch rewords the definition to
support all these SOCs.
Also have changes in description about iommu-map property updates
in PCI node.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 17 Mar 2017 08:12:31 +0000 (16:12 +0800)]
mtd: nand: remove nand size print from nand_init function
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Wenbin Song [Fri, 24 Mar 2017 10:05:48 +0000 (18:05 +0800)]
armv8: ls1043a/ls1046aqds: fix the offsets of MTD partitions on NOR flash
Fix the offsets of MTD partitions on Nor flash on ls1043ardb,
ls1043aqds and ls1046aqds boards. Delete the rcw, uboot env and fman
partitions. Add user partitions for general usage.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 10 Feb 2017 07:42:11 +0000 (15:42 +0800)]
pci: layerscape: enable PCIe config ready
In EP mode, to enable accesses from the Root Complex, the
CONFIG_READY bit must be set, otherwise any config attempts
from the Root Complex will be returned with config retry
status (CRS).
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
For validating images from uboot (Such as Kernel Image), either keys
from SoC fuses can be used or keys from a verified table of public
keys can be used. The latter feature is called IE Key Extension
Feature.
For Layerscape Chasis 3 based platforms, IE table is validated by
Bootrom and address of this table is written in scratch registers 13
and 14 via PBI commands.
Following are the steps describing usage of this feature:
1) Verify IE Table in ISBC phase using keys stored in fuses.
2) Install IE table. (To be used across verification of multiple
images stored in a static global structure.)
3) Use keys from IE table, to verify further images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Saksham Jain <saksham.jain@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Udit Agarwal [Fri, 3 Feb 2017 17:23:38 +0000 (22:53 +0530)]
armv8: LS2080A: Move sec_init to board_init
Moves sec_init to board_init rather than in misc_init function beacuse
PPA will be initialised in board_init function and for PPA validation
sec_init has to be done prior to PPA init.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Tom Rini [Fri, 24 Mar 2017 12:19:30 +0000 (08:19 -0400)]
Merge git://git.denx.de/u-boot-arc
This replaces legacy arch/arc/lib/timer.c implementation and allows us
to describe ARC Timers in Device Tree. Among other things that way we
may properly inherit Timer's clock from CPU's clock s they really run
synchronously.
Vlad Zakharov [Tue, 21 Mar 2017 11:49:49 +0000 (14:49 +0300)]
arc: use timer driver for ARC boards
This commit replaces legacy timer code with usage of arc timer
driver.
It removes arch/arc/lib/time.c file and selects CONFIG_CLK,
CONFIG_TIMER and CONFIG_ARC_TIMER options for all ARC boards by default.
Therefore we remove CONFIG_CLK option from less common axs101 and
axs103 defconfigs.
Also it removes legacy CONFIG_SYS_TIMER_RATE config symbol from
axs10x.h, tb100.h and nsim.h configs files as it is no longer required.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Vlad Zakharov [Tue, 21 Mar 2017 11:49:48 +0000 (14:49 +0300)]
arc: dts: separate single axs10x.dts file
We want to use the same device tree blobs in both Linux and U-Boot for
ARC boards.
Earlier device tree sources in U-Boot were very simplified and hadn't been
updated for quite a long period of time.
So this commit is the first step on the road to unified device tree blobs.
First of all we re-organize device tree sources for AXS10X boards.
As AXS101 and AXS103 boards consist of AXS10X motherboard and AXC001 and
AXC003 cpu tiles respectively we add corresponding device tree source
files: axs10x_mb.dtsi for motherboard, axc001.dtsi and axc003.dtsi for
cpu tiles and axs101.dts and axs103.dts to represent actual boards.
Also we delete axs10x.dts as it is no longer used.
One more important change - we add timer device to ARC skeleton device
tree sources as both ARC700 and ARCHS cores contain such timer.
We add core_clk nodes to abilis_tb100, nsim, axc001 and axc003 device tree
sources as it is referenced via phandle from timer node in common
skeleton.dtsi file.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Vlad Zakharov [Tue, 21 Mar 2017 11:49:47 +0000 (14:49 +0300)]
drivers: timer: Introduce ARC timer driver
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 10 Mar 2017 14:40:32 +0000 (15:40 +0100)]
arm: mvebu: theadorable: Add 'pcie' test command
This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will get printed. If the device is detected, the board will get
resetted so that an easy loop test can be done. The board will reboot
until the PCIe device is not detected.
Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the default of currently 2
is used. Values from 0...3 are possible (2 bits).
In this case of the theadorable board, PEX interface 0 needs a value
of 0 for the detection pulse width so that the PCIe device (Atheros
WLAN PCIe device) is consistantly detected.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Adam Shobash <adams@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de> Suggested-by: Adam Shobash <adams@marvell.com> Cc: Adam Shobash <adams@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm64: a37xx: Remove DM_I2C_COMPAT from the board config
Remove DM_I2C_COMPAT from the board configurations for
Armada 37xx platform boards for supressing the buid tim
warning.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm64: a37xx: Disable DB configurations on ESPRESSOBin board
Bypass XHCI and AHCi board configuration flow on ESPRESSOBin
community board.
The community board does not have i2c expander and USB VBUS
is always on, so the scan for AHCi and USB devices can be
faster without unneded configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm64: mvebu: Add default config for ESPRESSOBin board
Add initial default configuration for Marvell ESPRESSOBin
community board based on Aramda-3720 SoC
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
mvebu: a37xx: Add init for ESPRESSBin Topaz switch
Implement the board-specific network init function for
ESPRESSOBin community board, setting the on-board Topaz
switch port to forward mode and allow network connection
through any of the available Etherenet ports.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Stefan Roese <sr@denx.de>
mvebu: neta: a37xx: Add fixed link support to neta driver
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Terry Zhou <bjzhou@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm64: a37xx: Handle pin controls in early board init
Fix the default pin control values in a board-specific
function on early board init stage.
This fix allows the NETA driver to work in RGMII
mode until the full-featured pin control driver gets
introduced.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm64: a37xx: Enable bubt command support on A3720-DB
Enable mvebu bubt command support on A3720 DB
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Enable support for Marvell Ethernet PHYs on A37xx platforms
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm64: mvebu: Rename the db-88f3720 to armada-37xx platform
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
mvebu: usb: xhci: Add VBUS regulator supply to the host driver
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Rabeeh Khoury [Thu, 9 Feb 2017 10:39:10 +0000 (12:39 +0200)]
arm64: mvebu: dts: Add DTS file for MACCHIATOBin board
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Philipp Tomsich [Wed, 22 Feb 2017 18:06:04 +0000 (19:06 +0100)]
dtoc: make ScanTree recurse into subnodes
Previously, dtoc could only process the top-level nodes which led to
device nodes in hierarchical trees to be ignored. E.g. the mmc0 node
in the following example would be ignored, as only the soc node was
processed:
/ {
soc {
mmc0 {
/* ... */
};
};
};
This introduces a recursive helper method ScanNode, which is used by
ScanTree to recursively parse the entire tree hierarchy.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
drivers: ti_qspi: use syscon to get the address ctrl_mod_mmap register
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Lokesh Vutla [Mon, 13 Feb 2017 03:51:22 +0000 (09:21 +0530)]
dm: core: Fix Handling of global_data moving in SPL
commit 2f11cd9121658 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Felipe Balbi [Mon, 20 Feb 2017 11:24:14 +0000 (14:24 +0300)]
mmc: tangier: Add Intel Tangier eMMC/SDHCI driver
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Felipe Balbi [Mon, 20 Feb 2017 11:24:13 +0000 (14:24 +0300)]
mmc: pci: Add CONFIG_MMC_PCI
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tom Rini [Mon, 20 Mar 2017 18:19:27 +0000 (14:19 -0400)]
spl: Correct call to spl_common_init() with SPL_STACK_R_MALLOC_SIMPLE_LEN
Calls to IS_ENABLED() on a non-y/n option will always be false, even
when set. We can correct this by adding a new bool value that is set
based on the conditions required for SPL_STACK_R_MALLOC_SIMPLE_LEN to be
set instead.
Fixes: 340f418acd11 ("spl: Add spl_early_init()") Reported-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v2:
- Fix thinko pointed out by Lokesh
Jon Mason [Fri, 17 Mar 2017 16:12:14 +0000 (12:12 -0400)]
board: ns2: Add support for Broadcom Northstar 2
Add support for the Broadcom Northstar2 SoC and SVK (bcm958712k). The
BCM5871X is a series of quad-core 64-bit 2GHz ARMv8 Cortex-A57
processors targeting a broad range of networking applications.
Max Filippov [Thu, 16 Mar 2017 22:23:55 +0000 (15:23 -0700)]
Pass empty CFLAGS on invocation of libfdt/setup.py
When building u-boot tools in cross-build environment CFLAGS environment
variable set up for target is taken into an account when building code
for host. Make it empty on invocation of python.
This fixes the following build errors when cross-compiling for xtensa:
cc1: error: unrecognized command line option "-mlongcalls"
cc1: error: unrecognized command line option "-mauto-litpools"
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
The CAAM in IMX parts doesn't support public key hardware acceleration
(PKHA), so don't use RSA_FREESCALE_EXP. If you try to use it on IMX
(assuming you have the clocks enabled first) you will get back an
"Invalid KEY Command" error since PKHA isn't a valid key destination for
these parts.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tero Kristo [Thu, 16 Mar 2017 07:48:54 +0000 (09:48 +0200)]
ARM: am43xx: fix SOC revision print outs
Currently, AM43xx just re-uses the version strings from AM33xx which is
wrong; the actual values for AM43xx are different. Fix this by adding
a separate version string array for AM43xx and use this instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Reported-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Robert P. J. Day [Mon, 13 Mar 2017 10:50:55 +0000 (06:50 -0400)]
test-fit.py: Minor grammar/spelling/clarification tweaks
* Add note that execution needs Python development package installed
* Standardize on upper case "FIT", "FDT" as necessary for clarity
* Fix "tempoerary", "linex" typos
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Philipp Tomsich [Wed, 1 Mar 2017 20:10:39 +0000 (21:10 +0100)]
part_efi: support padding between the GPT header and partition entries
Some architectures require their SPL loader at a fixed address within
the first 16KB of the disk. To avoid an overlap with the partition
entries of the EFI partition table, the first safe offset (in bytes,
from the start of the device) for the entries can be set through
CONFIG_EFI_PARTITION_ENTRIES_OFF (via Kconfig)
When formatting a device with an EFI partition table, we may need to
leave a gap between the GPT header (always in LBA 1) and the partition
entries. The GPT header already contains a field to specify the
on-disk location, which has so far always been set to LBA 2. With this
change, a configurable offset will be translated into a LBA address
indicating where to put the entries.
Now also allows an override via device-tree using a config-node (see
doc/device-tree-bindings/config.txt for documentation).
Tested (exporting an internal MMC formatted with this) against Linux,
MacOS X and Windows.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: __maybe_unused on config_offset to avoid warning] Signed-off-by: Tom Rini <trini@konsulko.com>
Roger Quadros [Mon, 13 Mar 2017 13:04:33 +0000 (15:04 +0200)]
net: don't override ethernet address environment
If the ethernet address environment is set with a valid
ethernet address prevent overriding it as it is most likely
set by the user and he/she doesn't want board code to
automatically override it whatsoever.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Mon, 13 Mar 2017 13:04:30 +0000 (15:04 +0200)]
board: ti: am57xx-idk: Auto detect LCD Panel
AM571x IDK and AM572x IDK have optional LCD Kits that can be purchased.
These can be one of OSD101T2045 or the newer OSD101T2587. The LCD panel
itself has no registers that can be used to identify the panel, however,
the touchscreen controllers on the panels are different.
Hence to ease user experience, we can use the touch screen controller's
ID information to detect what kind of panel we use and select the
appropriate kernel dtb for the platform configuration.
NOTE: AM572x IDK default configuration is for LCD Connectivity, however
the AM571x IDK has a jumper (J51) that needs to be mounted for the IDK
to operate with LCD (Vs two PRUSS ethernet port option).
Touchscreen ID information is documented in:
http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Roger Quadros [Mon, 13 Mar 2017 13:04:29 +0000 (15:04 +0200)]
board: ti: am571x-idk: Update pinmux for ICSS2 Ethernet
Use the same convention that was used for ICSS1 Ethernet
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Roger Quadros [Mon, 13 Mar 2017 13:04:28 +0000 (15:04 +0200)]
board: ti: am571x-idk: Support 6 port Ethernet or 4 port Ethernet with LCD
The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).
Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.
J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb
At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.
For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.
Cc: Nishanth Menon <nm@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tom Rini [Mon, 20 Mar 2017 14:21:27 +0000 (10:21 -0400)]
travis-ci: Re-work i.MX6 jobs, clarify Freescale and AArch64
- The catch-all i.MX6 job has been exceeding the time limit again so
split this up further. We now have an i.MX6 job and an
everything-else job.
- The logic we use to say "Freescale and AArch64" can be more clearly
expressed with '&' rather than excluding various other things, so
clear that up.
ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Philipp Tomsich [Fri, 17 Mar 2017 19:34:53 +0000 (20:34 +0100)]
Kconfig: Migrate CONFIG_BAUDRATE
Move this in to Kconfig with a default of 115200.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
Stefan Agner [Tue, 14 Mar 2017 01:41:36 +0000 (18:41 -0700)]
ARM: vf610: move to standard arch/board approach
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137be ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
projects / u-boot / log