Alistair Francis [Thu, 25 Feb 2016 17:30:03 +0000 (09:30 -0800)]
ARM64: zynqmp: Use C pre-processor for includes in dts
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all ZynqMP device trees inline
with each other.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spl: mmc: raw: Try to load u-boot if Linux image is not found
If CONFIG_SPL_OS_BOOT is enabled and Linux image is not flashed at
RAW_MODE_KERNEL_SECTOR in MMC, spl still assumes that Linux is
available and tries to boot it and hangs. In order to avoid this,
adding a check to verify if parsed image header is of type IH_OS_LINUX.
If it fails then fall back to load u-boot image.
Hans de Goede [Sat, 9 Apr 2016 11:53:48 +0000 (13:53 +0200)]
arm: Replace v7_maint_dcache_all(ARMV7_DCACHE_CLEAN_INVAL_ALL) with asm code
v7_maint_dcache_all() does not work reliable when build with gcc6,
see: https://bugzilla.redhat.com/show_bug.cgi?id=1318788
While debugging this I learned that v7_maint_dcache_all() is unreliable
when build with gcc5 too when it is marked as noinline.
This commit fixes the reliability issues by replacing the C-code with
the ready to use asm implementation from the kernel.
Given that this code when written as C-code clearly is quite fragile
(also see the existing comments about the C-code being the way it is
to get optimal assembly) and that we have a proven asm alternative,
I believe that this is the best solution.
Note that we actually already had a copy of the kernel's
v7_flush_dcache_all() before this commit in
arch/arm/mach-uniphier/arm32/lowlevel_init.S.
This commit moves that code arch/arm/cpu/armv7/cache_v7_asm.S, renames
it to __v7_flush_dcache_all(), and adds a v7_flush_dcache_all() wrapper
which saves / restores the clobbered registers for use from C-code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Stefan Roese [Fri, 8 Apr 2016 13:56:29 +0000 (15:56 +0200)]
lib/crc8: Add crc start value
To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.
For non-zero CRC start values to work, I've reworked the function a bit.
The new implementation is copied from the Linux version in
drivers/i2c/i2c-core.c / i2c_smbus_pec(). Which supports non-zero
CRC stating values.
I've double-checked that the results for zero starting values are
identical to the results from the original version of this function.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Wed, 6 Apr 2016 17:46:59 +0000 (11:46 -0600)]
test/py: README: link to example hook scripts
When implementing test/py hook scripts, it's helpful to read some working
examples. Provide a link to some. The link was mentioned in the commit
message which first added test/py, but not in any documentation file.
Suggested-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Stefan Roese [Wed, 6 Apr 2016 09:02:22 +0000 (11:02 +0200)]
bootcounter_ram: Flush dcache after data is written into SDRAM
This patch adds a call to flush_dcache_range() to bootcount_store() to
make sure, that the bootcounter data (including the patterns) is
written to memory. Without this, platforms with dcache enabled may not
have the bootcounter updated upon reset.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Michal Simek [Tue, 5 Apr 2016 11:34:20 +0000 (13:34 +0200)]
disk: part: Enable get_info pointer for CONFIG_SPL_FAT_SUPPORT
The patch "dm: part: Convert partition API use to linker lists"
(sha1: 96e5b03c8ab749b6547f6a3ceb4d4b9f274211aa) is adding new
dependency for enabling SPL_EXT_SUPPORT to be able to get
information about DOS partition.
get_info is also required for FAT support only which is used on Xilinx
Zynq boards.
Reported-by: Nathan Rossi <nathan@nathanrossi.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Tue, 5 Apr 2016 02:00:41 +0000 (20:00 -0600)]
rpi: remove redundant board files
Now that rpi_*defconfig and Kconfig (rather than the config header file)
provide the identity of the build, we don't need to separate config
headers and board directories for each RPi variant. Set CONFIG_SYS_BOARD
and CONFIG_SYS_CONFIG_NAME so that we can get rid of the duplication. This
requires a tiny number of extra ifdefs in the config header.
The only disadvantage of this approach is that the $board/$board_name
environment variables aren't as descriptive as they used to be. This isn't
really an issue because those only exist to allow scripts to create DTB
filenames at runtime. However, the RPi board code already sets $fdtfile to
something more accurate based on FW-reported board ID anyway.
While at it, unify some Kconfig select options, and add a MAINTAINERS
entry for bcm283x too.
Partially-suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
stm32: stm32_flash: add memory barrier during flash write
After writing data to flash space, next instruction is checking if flash
controller is busy writing to the flash memory. Memory barrier is required here
to avoid transaction re-ordering for data write and busy status check.
Commit cf7c93cdd755 "usb: ehci: Implement V2P mapping"
introduced usage of virt_to_phys() in ehci-hcd.
Since there was no implementation of virt_to_phys() for ARC
compilation of the ehci-generic driver failed.
This change adds virt_to_phys() stub for ARC so now
USB driver for AXS101 board could be built again.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Hans de Goede <hdegoede@redhat.com> Acked-by: Marek Vasut <marex@denx.de>
Stephen Warren [Sat, 2 Apr 2016 03:14:15 +0000 (21:14 -0600)]
ARM: add Raspberry Pi 3 64-bit config
On all Pis so far, the VC FW provides a short stub to set up the ARM CPU
before entering the kernel (a/k/a U-Boot for us). This feature is not
currently supported by the VC FW when booting in 64-bit mode. However,
this feature will likely appear in the near future, and this U-Boot port
assumes that such a feature is in place. Without that feature, or a
temporary workaround described below, U-Boot will not boot.
Once the VC FW does provide the ARM stub, u-boot.bin built for rpi_3 can
be used drectly as kernel7.img, in the same way as any other RPi port. The
following config.txt is required:
# Fix mini UART input frequency, and setup/enable up the UART.
# Without this option, U-Boot will not boot, even if you don't care
# about the serial console. This option will always be required for
# all RPi3 use-cases, unless the PL011 UART is used, which is not
# yet supported by rpi_3* builds of U-Boot.
enable_uart=1
# Boot in AArch64 (64-bit) mode.
# It is possible that a future VC FW will remove the need for this
# option, instead auto-setting 32-/64-bit mode based on the "kernel"
# filename present on the SD card.
arm_control=0x200
Prior to the VC FW providing the ARM boot stub, you can use the following
steps to build an equivalent stub into the U-Boot binary:
git clone https://github.com/swarren/rpi-3-aarch64-demo.git \
../rpi-3-aarch64-demo
(cd ../rpi-3-aarch64-demo && ./build.sh)
Build U-Boot for rpi_3 in the usual way
cat ../rpi-3-aarch64-demo/armstub64.bin u-boot.bin > u-boot.bin.stubbed
Use u-boot.bin.stubbed as kernel7.img on the Pi SD card.
In this case, the following additional entries are required in config.txt:
# Tell the FW to load the kernel image at address 0, the reset vector.
kernel_old=1
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Sam Protsenko [Fri, 1 Apr 2016 18:27:50 +0000 (21:27 +0300)]
arm: socfpga: sr1500: Remove USB_GADGET
"buildman" tool revealed that USB_GADGET was enabled by mistake for this
board in process of moving that option to Kconfig. Remove it to bring
things back to correct state.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Acked-by: Stefan Roese <sr@denx.de>
Marek Vasut [Sun, 20 Mar 2016 17:02:44 +0000 (18:02 +0100)]
arm: socfpga: sockit: Use more relaxed DRAM timings
The currently present DRAM timings generated from GHRD 14.0 did
not work on SoCkit rev. D because they were too tight. Load the
DRAM timings from GHRD 13.0 which are more relaxed and work with
SoCkit rev. D.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Chin Liang See <clsee@altera.com>
Marek Vasut [Mon, 21 Mar 2016 12:38:11 +0000 (13:38 +0100)]
arm: socfpga: Handle phy-mode OF property for GMACs
Thus far, the socfpga init code had hard-coded the configuration
of the ethernet PHY interface to RGMII in the ethernet registers
in sysmgr space, so PHYs connected in another modes did not work.
This patch fixes support for configurations where the ethernet PHYs
are connected over MII/GMII/RMII interfaces by parsing the phy-mode
OF property of the GMACs and configuring the ethernet registers in
sysmgr space accordingly.
Hans de Goede [Sat, 2 Apr 2016 18:46:09 +0000 (20:46 +0200)]
musb: sunxi: Do not allocate musb struct multiple times
The probe function of the musb host driver can be called multiple
times. The code assumes that it can save the pointer to the allocated
musb struct in the driver model priv_auto_alloc data, but this data
gets free-ed on a probe failure or on removal, so we must save the
pointer elsewhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 3 Apr 2016 07:18:53 +0000 (09:18 +0200)]
usb: kbd: Do not deregister usbkbd twice when using dm
The dm usb_kbd_remove function() will deregister the usb keyboard for
us on a "usb reset" / "usb stop" so there is no need to manually call
usb_kbd_deregister() in the dm case.
This commit removes usb_kbd_deregister() in the dm case fixing the
following "usb reset" errors:
usb_kbd_remove: warning, ret=-6
device_remove: Device 'usb_kbd' failed to remove, but children are gone
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
powerpc: mpc85xx: Enable pre-relocation malloc for MPC85xx
To enable DM on MPC85xx, we need pre-relocation malloc, which is
implemented in this patch.
We also make sure that the IVORs are always 4-aligned on e500 to prevent
alignment exceptions caused by code changes in start.S.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Cc: York Sun <york.sun@nxp.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 6 Apr 2016 20:22:10 +0000 (13:22 -0700)]
powerpc: Replace CONFIG_SYS_INIT_RAM_END with CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_SIZE may be used out of the board header file.
Some boards use CONFIG_SYS_INIT_RAM_END for the same purpose. To
unify the macros, use CONFIG_SYS_INIT_RAM_SIZE for all.
Signed-off-by: York Sun <york.sun@nxp.com> CC: Mario Six <mario.six@gdsys.cc> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
The commands for the VSC9953 l2 switch from T1040 became generic in
patch https://patchwork.ozlabs.org/patch/499748/ and the define
was renamed.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Mon, 4 Apr 2016 18:41:26 +0000 (11:41 -0700)]
armv8: LS2080A: Consolidate LS2080A and LS2085A
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com> CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Ed Swarthout [Mon, 28 Mar 2016 21:16:01 +0000 (16:16 -0500)]
armv8: LSCH2 early and final mmu needs matching NS attribute
When switching between the early and final mmu tables, the stack will
get corrupted if the Non-Secure attribute is different. For ls1043a,
this issue is currently masked because flush_dcache_all is called
before the switch when CONFIG_SYS_DPAA_FMAN is defined.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
drivers: net: vsc9953: Fix bug when PVID is shown for disabled ports only
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
drivers: net: vsc9953: Do not configure disabled ports
Some SerDes protocols might not enable all l2switch ports. In this case,
these ports should not be configured to perform Rx/Tx operations.
This also fixes an issue when flooded frames were also switched to
disabled ports and frames start to accumulate, consuming memory
and eventually causing head-of-line blocking for other frames.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
Peng Fan [Tue, 15 Mar 2016 09:57:50 +0000 (17:57 +0800)]
fsl: esdhc: consolidate fsl_esdhc_cfg structure
We can use phys_addr_to for esdhc_base to discard
the #ifdef.
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: York Sun <york.sun@nxp.com> Cc: Yangbo Lu <yangbo.lu@nxp.com> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
Peng Fan [Fri, 25 Mar 2016 06:16:56 +0000 (14:16 +0800)]
fsl: esdhc: support driver model
Support Driver Model for fsl esdhc driver.
1. Introduce a new structure struct fsl_esdhc_priv
2. Refactor fsl_esdhc_initialize which is originally used by board code.
- Introduce fsl_esdhc_init to be common usage for DM and non-DM
- Introduce fsl_esdhc_cfg_to_priv to build the bridge for non-DM part.
- The original API for board code is still there, but we use
'fsl_esdhc_cfg_to_priv' and 'fsl_esdhc_init' to serve it.
3. All the functions are changed to use 'struct fsl_esdhc_priv', except
fsl_esdhc_initialize.
4. Since clk driver is not implemented, use mxc_get_clock to geth
the clk and fill 'priv->sdhc_clk'.
Has been tested on i.MX6UL 14X14 EVK board:
"
=>dm tree
....
simple_bus [ + ] | `-- aips-bus@02100000
mmc [ + ] | |-- usdhc@02190000
mmc [ + ] | |-- usdhc@02194000
....
=> mmc list
FSL_SDHC: 0 (SD)
FSL_SDHC: 1 (SD)
"
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: York Sun <york.sun@nxp.com> Cc: Yangbo Lu <yangbo.lu@nxp.com> Cc: Hector Palacios <hector.palacios@digi.com> Cc: Eric Nelson <eric@nelint.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Simon Glass <sjg@chromium.org> Tested-By: Eric Nelson <eric@nelint.com> Reviewed-by: York Sun <york.sun@nxp.com>
Chris Packham [Mon, 1 Feb 2016 23:35:09 +0000 (12:35 +1300)]
kirkwood_nand: claim MPP pins on the fly
Claim the MPP pins for the NAND flash controller only when it's actually
being used. This allows the pins to be shared with the SPI interface
which already supports an equivalent on-access MPP reconfiguration.
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Scott Wood <oss@buserror.net> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 11 Feb 2016 10:37:38 +0000 (11:37 +0100)]
spi: kirkwood_spi: Add support for multiple chip-selects on MVEBU
Currently only chip-select 0 is supported by the kirkwood SPI driver.
The Armada XP / 38x SoCs also use this driver and support multiple chip
selects. This patch adds support for multiple CS on MVEBU.
The register definitions are restructured a bit with this patch. Grouping
them to the corresponding registers.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Jagan Teki <jteki@openedev.com>
Michal Simek [Fri, 18 Mar 2016 22:43:39 +0000 (23:43 +0100)]
ARM: zynq: Add uEnv.txt support
preboot macro load the uEnv.txt from mmc 0 when bootmode is mmc. uenvcmd is
executed after load of uEnv.txt if it is defined in the uEnv.txt env text
file.
The default importbootenv macro reads the uEnv.txt from mmc.
Additional to this, usb_loadbootenv is added to support loading uEnv.txt
from usb dev 0.
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 8 Feb 2016 08:34:53 +0000 (09:34 +0100)]
ARM64: zynqmp: Read RAM information from DT
Read information about memory from DT. This patch simplify life with
synchronization between DT and board files.
dram_init() only needs maximum RAM size below 4GB that's why please sort
banks in memory node.
dram_init_banksize() copies memory setup to bi_dram[].
This will avoid reading information from DT twice.
Memory test start/end were changed to DDR location to let memtest still
compiled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>