Stephen Warren [Thu, 20 Aug 2015 23:38:42 +0000 (17:38 -0600)]
ARM: tegra: replace V_PROMPT define with kconfig
Commit 181bd9dc61d2 "kconfig: add config option for shell prompt" replaced
define V_PROMPT with Kconfig option SYS_PROMPT. This crossed with patches
adding Tegra T210 boards. Migrate the boards to the new scheme.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 19 Aug 2015 23:03:59 +0000 (17:03 -0600)]
ARM: tegra: fix PLLP frequency calc on T210
AFAIK, for all PLLs on all Tegra SoCs, the primary PLL output frequency
is (input * m) / (n * p). However, PLLP's primary output (pllP_out0) on
T210 is the VCO output, and divp is not applied. pllP_out2 does have divp
applied. All other pllP_outN are divided down from pllP_out0. We only
support pllP_out0 in U-Boot at the time of writing.
Fix clock_get_rate() to handle this special case.
This corrects the returned rate for PLLP to be 408MHz rather than 204MHz.
In turn, this causes high enough dividers to be calculated for the various
peripheral clocks that feed off of PLLP. Without this, some peripherals
failed to operate correctly. For instance, one of my SD cards worked
perfectly but an older (presumably slower) card could not be read.
Note that prior to commit 722e000ccd72 "Tegra: PLL: use per-SoC pllinfo
table instead of PLL_DIVM/N/P, etc.", the calculated PLL frequency was
816MHz since the wrong values were being extracted from the PLLP divider
register. This caused overly large peripheral dividers to be calculated,
which while wrong, didn't cause any correctness issues; things simply ran
slower than they could.
Reported-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 19 Aug 2015 21:15:41 +0000 (15:15 -0600)]
ARM: tegra: fix COUNTER_FREQUENCY for T210
While T210 boards all have 38.4MHz crystals, per the TRM, the only
supported configuration is to divide the crystal frequency by 2 to
generate clk_m, which is what feeds the ARM generic timers amongst other
things. Fix the value of COUNTER_FREQUENCY to reflect this divide-by-2.
When I queried the 19.2 value in Tom's original T210 patches, I wasn't
aware of this extra divide-by-2, and didn't notice any effect from the
incorrect value, since its only used if U-Boot is booted in EL3, whereas
I'm booting it in EL2.
Reported-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 14 Aug 2015 04:34:22 +0000 (22:34 -0600)]
ARM: tegra: Add p2371-2180 board
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
When enabling CONFIG_API and chain-loading GRUB2 on jetson-tk1, only the
eMMC would show up as (hd0), but not the SD card, leading to GRUB not
finding its configuration and modules, falling back to a rescue shell.
This is because enum_ended would get set for !more after returning a
cookie for the first MMC device in group 3.
Fix this by properly setting the "more" argument also in the case of the
first storage device of a group.
Stefan Roese [Mon, 14 Sep 2015 07:17:36 +0000 (09:17 +0200)]
arm: Remove unused ST-Ericsson u8500 arch
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: John Rigby <john.rigby@linaro.org> Cc: Simon Glass <sjg@chromium.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tom Rini <trini@konsulko.com> Cc: Heiko Schocher <hs@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Stefan Roese [Mon, 14 Sep 2015 06:47:47 +0000 (08:47 +0200)]
mtd: nand: fsmc: Fixes and cleanup for fsmc_nand_switch_ecc()
This patch addresses some comments raised by Scott in the last versions.
Here the changes in detail:
- Removed __maybe_unused as its not needed
- Added check for strength == 4 and error out for the unsupported
ECC strength values
- Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this
will be done in nand_scan_tail()
- Set .caclulate back to fsmc_read_hwecc() in the HW case
- Added comment that this function will only be called on SPEAr platforms,
not supporting the BCH8 HW ECC (FSMC_VER8)
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com> Acked-by: Scott Wood <scottwood@freescale.com>
env: import: hashtable: Prevent buffer overrun when importing environment from file
Lets consider following scenario:
- One uses echo -n "key=value" to define environment variable in a file (single variable)
- The file content is "key=value" without any terminating byte (e.g. 0x0a or
0x0d).
- The file is loaded to u-boot non zero'ed RAM buffer (with load command).
- Then "env import -t -r $loadaddr $filesize" is executed.
- Due to lack of proper termination byte we have classical example of buffer
overrun.
This patch prevents from this by allocating one extra byte than size and
explicitly null terminate it.
There should be no change for normal env import operation after applying
this patch.
Tom Rini [Thu, 3 Sep 2015 18:54:03 +0000 (14:54 -0400)]
ti814x_evm: Switch to SYS_GENERIC_BOARD
Take over maintainership as well. Not tested as PG2.0 (which I have)
needs additional work over PG1.0 (which Matt has).
Cc: Matt Porter <mporter@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Thu, 6 Aug 2015 21:31:02 +0000 (15:31 -0600)]
fdt: add new fdt address parsing functions
fdtdec_get_addr_size() hard-codes the number of cells used to represent
an address or size in DT. This is incorrect in many cases depending on
the DT binding for a particular node or property (e.g. it is incorrect
for the "reg" property). In most cases, DT parsing code must use the
properties #address-cells and #size-cells to parse addres properties.
This change splits up the implementation of fdtdec_get_addr_size() so
that the core logic can be used for both hard-coded and non-hard-coded
cases. Various wrapper functions are implemented that support cases
where hard-coded cell counts should or should not be used, and where
the client does and doesn't know the parent node ID that contains the
properties #address-cells and #size-cells.
dev_get_addr() is updated to use the new functions.
Core functionality in fdtdec_get_addr_size_fixed() is widely tested via
fdtdec_get_addr_size(). I tested fdtdec_get_addr_size_auto_noparent() and
dev_get_addr() by manually modifying the Tegra I2C driver to invoke them.
Much of the core implementation of fdtdec_get_addr_size_fixed(),
fdtdec_get_addr_size_auto_parent(), and
fdtdec_get_addr_size_auto_noparent() comes from Thierry Reding's
previous commit "fdt: Fix fdtdec_get_addr_size() for 64-bit".
Based-on-work-by: Thierry Reding <treding@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Cc: Simon Glass <sjg@chromium.org> Cc: Michal Suchanek <hramrach@gmail.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Dropped #define DEBUG at the top of fdtdec.c: Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Guinot [Thu, 3 Sep 2015 09:12:20 +0000 (11:12 +0200)]
ARM: Kirkwood: fix IDE configuration on LaCie boards
On the LaCie boards netspace_max_v2 and net2big_v2, two internal hard
drives are available. Additionally on the d2net_v2 board, an extra hard
drive can be plugged via eSATA.
This patch updates CONFIG_SYS_IDE_MAXBUS and CONFIG_SYS_IDE_MAXDEVICE
accordingly for this boards.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
mx6ul_14x14_evk: Use the default CONFIG_SYS_PBSIZE
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
arm: mx6: cm-fx6: modify device tree for old revisions of utilite
Old revisions of Utilite (a miniature PC based on cm-fx6) do not have
a card detect for mmc, and thus the kernel needs to be told that
there's a persistent storage on usdhc3 to force it to probe the mmc
card.
Check the baseboard revision and modify the device tree accordingly
if needed.
compulab: eeprom: propagate error value in read_mac_addr()
cl_eeprom_read_mac_addr() doesn't differentiate between success case and
inability to access eeprom. Fix this by propagating the return value of
cl_eeprom_setup().
Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Peng Fan [Sun, 6 Sep 2015 07:02:34 +0000 (15:02 +0800)]
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
Running mxsboot on a big-endian system produces a sd image which
cannot be started by the i.MX28 ROM. It complains on the debug
uart as following:
0x8020a009
0x80502008
0x8020a009
0x80502008
...
Enforcing all fields within the BCB to little-endian make
the image bootable again.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Marek Vasut <marex@denx.de>
Adrian Alonso [Thu, 3 Sep 2015 16:49:28 +0000 (11:49 -0500)]
imx: mx7dsabresd: Add support for MX7D SABRESD board
* Add i.MX7D SABRESD target board support with enabled modules:
UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX.
Build target: mx7dsabresd_config
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Adrian Alonso [Wed, 2 Sep 2015 18:54:18 +0000 (13:54 -0500)]
imx: imx7d: clock control module support
* Add Clock control module (CCM) support
* iMX7D SoC introduces 3 main clock sysmtem abstraction for clock
root frequency generation denominated clock slices.
Core clock slice: hihg speed clock for ARM core
Bus clock slice: for bus clocks
IP clock slice: Peripheral clocks
* At system boot ROM enables PLL_ARM, PLL_DDR, PLL_SYS, PLL_ENET
In u-boot, we have to:
- Configure PFD3- PFD7 for freq we needed in u-boot
- Set clock root for peripherals (ip channel)
Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
Adrian Alonso [Wed, 2 Sep 2015 18:54:16 +0000 (13:54 -0500)]
imx: system counter driver for imx7d and mx6ul
Add system counter driver for imx7d and mx6ul
imx7 and imx6ul supports system counter timer as well as
GPT timer (arch/arm/imx-common/timer.c); The default for
imx7 is systemcounter timer.
Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Stephen Warren [Fri, 11 Sep 2015 23:10:02 +0000 (17:10 -0600)]
usb: ci_udc: fix emissions of ZLPs
Commit 6a132416359e "ci_udc: Update the ci_udc driver to support bulk
transfers" caused the value of "len" to change without updating subsquent
users of that variable in ci_ep_submit_next_request(). This caused the
code that detects when to emit ZLPs (Zero Length Packets) never to
trigger, which in turn caused host timeouts when a ZLP was required,
which in turn broke tests/dfu/, even despite the assertion in that
commit's description that "These changes are tested for both the DFU and
lthor."
Fix this by modifying the added dtd iteration code not to modify "len",
but rather to keep state in a separate variable. Rename the variables
while we're at it so they describe their purpose better.
Fixes: 6a132416359e ("ci_udc: Update the ci_udc driver to support bulk transfers") Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Without this function, uboot will hang when executing fastboot comamnd.
See following flow:
"fastboot_tx_write_str->fastboot_tx_write->usb_ep_dequeue->ep->ops->dequeue"
without implement ci_udc dequeue function, ep->ops->dequeue is NULL, then
uboot will hang.
Tested on mx6qsabresd board with fastboot enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Cc: "Łukasz Majewski" <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
The current simplify lpc32xx gpio driver implementation assume a
maximum of 32 GPIO per port; there are a total of 22 GPI, 24 GPO
and 6 GPIO to managed on port 3.
Update the driver to fix the following:
1) When requesting GPI_xx and GPO_xx on port 3 (xx is the same number)
the second call to "gpio_request" will return -EBUSY.
2) The status of GPO_xx pin report the status of the
corresponding GPI_xx pin when using the "gpio status" command.
3) The gpio driver may setup the direction register for the wrong
gpio when calling "gpio_direction_input" (GPI_xx) or
"gpio_direction_output" (GPO_xx) on port 3; the call to the
direction is require to use the "gpio status" command.
The following change were done in the driver:
1) port3 GPI are cache in a separate 32 bits in the array.
2) port3 direction register written only for GPIO pins.
3) port3 GPO & GPIO (as output) are read using "p3_outp_state".
4) LPC32XX_GPI_P3_GRP updated to match the change.
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
igep00x0: Switch to use the generic distro configuration and environment.
This patch changes a little bit the environment, current environment was broken
for a long time, and board don't as expected sometimes, on production systems
this is fixed adding boot script. I think it's time to change this to make a
system conformant environment and use generic distro configurations and
environment instead. We can use a boot script for the old way boot mode.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Stephen Warren [Sat, 5 Sep 2015 04:03:51 +0000 (22:03 -0600)]
ARM: tegra: enable DFU for RAM
This allows transferring data directly to/from RAM. For example, one
could create a boot script that starts DFU on a RAM region, then once
DFU exits (which is under the control of the attached USB host, via a
USB bus reset), uses the code/data that was received over DFU.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Sat, 5 Sep 2015 04:03:50 +0000 (22:03 -0600)]
ARM: tegra: enable filesystem writing
Writing to files is a useful feature in general, so enable it everywhere.
The primary purpose is to make DFU useful on filesystems in addition to
raw devices.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Sat, 5 Sep 2015 04:03:49 +0000 (22:03 -0600)]
ARM: tegra: tweak DFU buffer sizes
CONFIG_SYS_DFU_DATA_BUF_SIZE defines the size of chunks transferred
across USB. This doesn't need to be particularly large, since it doesn't
limit the overall transfer size.
CONFIG_SYS_DFU_MAX_FILE_SIZE is used to buffer an entire file before
writing it to a filesystem. This define limits the maximum file size that
may be transferred. Bump this up to 32MiB in order to support large
uncompressed kernel images.
Both of these buffers are dynamically allocated, and so the size of both
needs to be taken into account when calculating the required malloc
region size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Sat, 5 Sep 2015 04:03:48 +0000 (22:03 -0600)]
ARM: tegra: fix malloc region sizing
Commit 52a7c98a1772 "tegra-common: increase malloc pool len by dfu mmc
file buffer size" updated the definition of CONFIG_SYS_MALLOC_LEN for
Tegra to take account of the DFU buffer size. However, this change had
no effect, since typical Tegra board config headers don't set the DFU-
related defines until after tegra-common.h is included. Fix this by
moving the affected conditional code to tegra-common-post.h, which is
included last. Also move the definition of SYS_NONCACHED_MEMORY since
it's a related and adjacent definition.
Fix the condition to test for the DFU feature, rather than specifically
MMC DFU support, so it applies in all cases.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Sat, 5 Sep 2015 04:03:47 +0000 (22:03 -0600)]
dfu: mmc: buffer file reads too
When writing to files in a filesystem on MMC, dfu_mmc.c buffers up the
entire file content until the end of the transaction, at which point the
file is written in one go. This allows writing files larger than the USB
transfer size (CONFIG_SYS_DFU_DATA_BUF_SIZE); the maximum written file
size is CONFIG_SYS_DFU_MAX_FILE_SIZE (the size of the temporary buffer).
The current file reading code does not do any buffering, and so limits
the maximum read file size to the USB transfer size. Enhance the code to
do the same kind of buffering as the write path, so the same file size
limits apply.
Remove the size checking code from dfu_read() since all read paths now
support larger files than the USB transfer buffer.
Stephen Warren [Sat, 5 Sep 2015 04:03:46 +0000 (22:03 -0600)]
dfu: don't keep freeing/reallocating
DFU currently allocates buffer memory at the start of each data transfer
operation and frees it at the end. Especially since memalign() is used to
allocate the buffer, and various other allocations happen during the
transfer, this can expose the code to heap fragmentation, which prevents
the allocation from succeeding on subsequent transfers.
Fix the code to allocate the buffer once when DFU mode is initialized,
and free the buffer once when DFU mode is exited, to reduce the exposure
to heap fragmentation.
The failure mode is:
// Internally to memalign(), this allocates a lot more than s to guarantee
// that alignment can occur, then returns chunks of memory at the start/
// end of the allocated buffer to the heap.
p = memalign(a, s);
// Various other malloc()s occur here, some of which allocate the RAM
// immediately before/after "p".
//
// DFU transfer is complete, so buffer is released.
free(p);
// By chance, no other malloc()/free() here, in DFU at least.
//
// A new DFU transfer starts, so the buffer is allocated again.
// In theory this should succeed since we just free()d a buffer of the
// same size. However, this fails because memalign() internally attempts
// to allocate much more than "s", yet free(p) above only free()d a
// little more than "s".
p = memalign(a, s);
Stephen Warren [Sat, 5 Sep 2015 04:03:44 +0000 (22:03 -0600)]
ext4: free allocations by parse_path()
parse_path() malloc()s the entries in the array it's passed. Those
allocations must be free()d by the caller, ext4fs_get_parent_inode_num().
Add code to do this.
For this to work, all the array entries must be dynamically allocated,
rather than a mix of dynamic and static allocations. Fix parse_path() not
to over-write arr[0] with a pointer to statically allocated data.
Stephen Warren [Sat, 5 Sep 2015 04:03:43 +0000 (22:03 -0600)]
ext4: avoid calling ext4fs_mount() twice, which leaks
ext4_write_file() is only called from the "fs" layer, which calls both
ext4fs_mount() and ext4fs_close() before/after calling ext4_write_file().
Fix ext4_write_file() not to call ext4fs_mount() again, since the mount
operation malloc()s some RAM which is leaked when a second mount call
over-writes the pointer to that data, if no intervening close call is
made.
Stephen Warren [Sat, 5 Sep 2015 04:03:42 +0000 (22:03 -0600)]
usb: gadget: don't leak configs when unbinding
By the time g_dnl_unbind() is run, cdev->config has been set to NULL,
so the free() there does nothing, and the config struct is leaked.
Equally, struct usb_gadget contains a linked list of config structs, so
the code should iterate over them all and free each one, rather than
freeing one particular config struct.
composite_unbind() already iterates over the list of config structs, and
unlinks each from the linked list. Fix this loop to free() each struct as
it's unlinked and otherwise forgotten.
FIX: fat: Provide correct return code from disk_{read|write} to upper layers
It is very common that FAT code is using following pattern:
if (disk_{read|write}() < 0)
return -1;
Up till now the above code was dead, since disk_{read|write) could only
return value >= 0.
As a result some errors from medium layer (i.e. eMMC/SD) were not caught.
The above behavior was caused by block_{read|write|erase} declared at
struct block_dev_desc (@part.h). It returns unsigned long, where 0
indicates error and > 0 indicates that medium operation was correct.
This patch as error regards 0 returned from block_{read|write|erase}
when nr_blocks is grater than zero. Read/Write operation with nr_blocks=0
should return 0 and hence is not considered as an error.
Simon Glass [Wed, 2 Sep 2015 23:24:57 +0000 (17:24 -0600)]
Move malloc_cache_aligned() to its own header
At present malloc.h is included everywhere since it recently was added to
common.h in this commit:
4519668 mtd/nand/ubi: assortment of alignment fixes
This seems wasteful and unnecessary. We have been trying to trim down
common.h and put separate functions into separate header files and that
change goes in the opposite direction.
Move malloc_cache_aligned() to a new header so that this can be avoided.
The header would perhaps be better named as alignmem.h but it needs to be
included after common.h and people might be confused by this. With the name
memalign.h it fits nicely after malloc() in most cases.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Stefan Roese [Wed, 2 Sep 2015 09:11:00 +0000 (11:11 +0200)]
arm: spear: Enable THUMB mode on x600 board
To reduce the size of the U-Boot image on the x600 board, lets enable
the THUMB mode. This reduces the overall size to less than 0x6000
bytes. Fitting it again in the onboard NOR flash.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Viresh Kumar <viresh.kumar@linaro.org>
Stefan Roese [Wed, 2 Sep 2015 09:10:59 +0000 (11:10 +0200)]
arm: spear: Add BCH4 SW support to SPEAr600 x600 board
This board is equipped with a Micron NAND chip (MT29F1G08ABADAH4) that
needs 4-bit ECC. But the SPEAr600 only supports 1-bit HW ECC internally.
This patch enables the SW 4-bit BCH support for this board.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Viresh Kumar <viresh.kumar@linaro.org>
Stefan Roese [Wed, 2 Sep 2015 09:10:58 +0000 (11:10 +0200)]
arm: spear: Add command to switch between 1-bit HW ECC and SW BCH4
This patch adds the "nandecc" command to switch between the SPEAr600 internal
1-bit HW ECC and the 4-bit SW BCH4 ECC. This can be needed to support NAND
chips with a stronger ECC than 1-bit, as on the x600. And to dynamically
switch between both ECC schemes for backwards compatibility.
Stefan Roese [Wed, 2 Sep 2015 12:29:12 +0000 (14:29 +0200)]
mtd: nand: fsmc: Add BCH4 SW ECC support for SPEAr600
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your config header:
#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH
And use the command "nandecc bch4" to select this ECC scheme upon runtime.
Tested on SPEAr600 x600 board.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
projects / u-boot / log