Chen-Yu Tsai [Wed, 7 Jun 2017 07:11:49 +0000 (15:11 +0800)]
sunxi: psci: Move entry address setting to separate function
Currently we set the entry address in the psci_cpu_on function.
However R40 has a different register for this. This resulted in
an #ifdef / #else block in psci_cpu_on, which we avoided having
in the first place.
Move this part into a separate function, defined differently for
the R40 as opposed to the other single cluster platforms.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Icenowy Zheng [Sat, 3 Jun 2017 09:10:25 +0000 (17:10 +0800)]
sunxi: add a defconfig for SoPine w/ official baseboard
The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
detect pin of the MicroSD slot is broken, however, it doesn't matter as
the design of SoPine didn't allow hot-swapping the MicroSD card (The
MicroSD slot is at the back of the SoM, and when the SoM is installed on
the baseboard, it's nearly impossible to remove the MicroSD).
The official baseboard of it is a board with nearly the same connectors
with the original Pine64+, with the MicroUSB power jack replaced, and
at the position of MicroSD slot a eMMC module slot is added.
Add support for SoPine with the official baseboard by adding its
defconfig file. It still uses the device tree of Pine64, however, it
will change after a proper device tree of SoPine with baseboard is
accepted by Linux mainline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Update board/sunxi/MAINTAINERS] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Icenowy Zheng [Sat, 3 Jun 2017 09:10:19 +0000 (17:10 +0800)]
sunxi: enable dual rank detection in DesignWare-like DRAM code
The DesignWare-like DRAM code used to set the controller defaultly to
single rank mode, which makes it not able to detect the second rank.
Set the default value to dual rank, thus the rank detection code can
work and finally the rank setting will be the correct value.
Currently we know little about the dual-rank on R40, and the usage
of A15 address line seems to be breaking dual-rank support. The only R40
board currently available (Sinovoip Banana Pi M2 Ultra) uses A15 rather
than dual-rank, thus we cannot do research for it. So dual rank detection
is temporarily disabled on R40.
This change is tested on a Orange Pi One (H3, single rank), a Pine64+
2GiB version (A64, single rank) , a Pinebook early prototype with DDR3
(A64, dual rank) and a SoPine with some LPDDR3 patch (A64, dual CS pins
on one chip).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Icenowy Zheng [Sat, 3 Jun 2017 09:10:15 +0000 (17:10 +0800)]
sunxi: Rename bus-width related macros in H3 DRAM code
The DesignWare DRAM controller used by H3 and newer SoCs use a bit to
identify whether the DRAM is half-width.
As H3 itself come with 32-bit DRAM, the two modes of the bit used to be
named "MCTL_CR_32BIT" and "MCTL_CR_16BIT", but for SoCs with 16-bit DRAM
they're really 8-bit and 16-bit.
Rename the bit's macro, and also rename the variable name in
dram_sun8i_h3.c.
This commit do not add 16-bit DRAM controller support, but the support
will be introduced in next commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Icenowy Zheng [Sat, 3 Jun 2017 09:10:14 +0000 (17:10 +0800)]
sunxi: makes an invisible option for H3-like DRAM controllers
Allwinner SoCs after H3 (e.g. A64, H5, R40, V3s) uses a H3-like
DesignWare DRAM controller, which do not have official free DRAM
initialization code, but can use modified dram_sun8i_h3.c.
Add a invisible option for easier DRAM initialization code reuse.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This patch fixes the below warning by typecasting it properly
fs/ubifs/ubifs.c: In function 'ubifs_load':
fs/ubifs/ubifs.c:942:29: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
err = ubifs_read(filename, (void *)addr, 0, size, &actread);
Phil Edworthy [Thu, 1 Jun 2017 06:33:28 +0000 (07:33 +0100)]
arm: Add Kconfig symbols used for Linux asm compatibility
Rather than change asm files that come from Linux, add the symbols
to Kconfig. Since one of the symbols is for thumb2 builds, make
CPU_V7M always select them.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Patrice Chotard [Tue, 30 May 2017 13:06:31 +0000 (15:06 +0200)]
drivers: ram: stm32: fix compilation issue
If CONFIG_CLK flag is not set, compilation raises the
following error message:
drivers/ram/stm32_sdram.c: In function 'stm32_fmc_probe':
drivers/ram/stm32_sdram.c:154:2: error: 'ret' undeclared (first use in this function)
ret = stm32_sdram_init(dev);
Michal Simek [Mon, 29 May 2017 08:26:53 +0000 (10:26 +0200)]
arm64: Add NOLOAD attribute NOLOAD to .bss sections
Mark explicitly bss sections to not be loaded at
run time.
The similar patch was done in past by:
"Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections"
(sha1: 64134f011254123618798ff77c42ba196b2ec485)
The problem is related to latest toolchain added to Xilinx
v2017.1 design tools where jtag loader is trying to access
ununitialized memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 29 May 2017 07:11:32 +0000 (09:11 +0200)]
ARMv8: Add support for poweroff via PSCI
Add support for calling poweroff in case of psci is wired.
Based on the same solution as is used for reset.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move all logic in to fwcall.c as other ARMs implement poweroff
via PMIC] Signed-off-by: Tom Rini <trini@konsulko.com>
With clang-3.8 we see warnings like:
cmd/ethsw.c:304:6: warning: implicit conversion from
enumeration type 'enum ethsw_keyword_opt_id' to different enumeration type
'enum ethsw_keyword_id' [-Wenum-conversion]
ethsw_id_pvid_no,
^~~~~~~~~~~~~~~~
Because we have one enum for ethsw_keyword_id and a second enum for
ethsw_keyword_opt_id. This ends up being safe as ethsw_keyword_opt_id
explicitly starts after ethsw_keyword_id enum ends. Disable the
warning here rather than collapse these into one enum and rely on
comments to denote where optional keywords begin.
Cc: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Wed, 24 May 2017 15:04:03 +0000 (11:04 -0400)]
scripts/Makefile.lib: Only apply u-boot.dtsi files in the target directory
We only want to apply files such as 'omap5-u-boot.dtsi', which resides
in arch/arm/dts/ to other files in arch/arm/dts/ and not say
test/overlay/. Rework the make logic to check for -u-boot.dtsi files in
the same directory as their target dts.
Cc: Simon Glass <sjg@chromium.org> Reported-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
ARM: ti: Update layout for MMC and eMMC (env and dfu)
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
"spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
kernels
Fixing this requires growing some regions and moving others.
Care has been taken to leave some room for further growth of
"spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the
region is not free space that can be used to grow "u-boot.img.raw".
The MLO region is 0x100 sectors wide but the 0x100 are unused in case the
MLO comes too overflow this areas.
The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tom Rini [Mon, 22 May 2017 19:21:57 +0000 (19:21 +0000)]
common/spl/Kconfig: Use 'if SPL' / 'if TPL' guards
Much of the entries here simply depend on SPL (or TPL). Instead of this
redundancy use if SPL / if TPL to guard the rest of the choices and only
show them when we have the relevant option enabled.
Simon Glass [Mon, 22 May 2017 11:05:35 +0000 (05:05 -0600)]
bootstage: Support SPL
At present bootstage only supports U-Boot proper. But SPL can also consume
boot time so it is useful to have the record start there.
Add bootstage support to SPL. Also support stashing the timing information
when SPL finishes so that it can be picked up and reported by U-Boot
proper. This provides a full boot time record, excluding only the time
taken by the boot ROM.
Simon Glass [Mon, 22 May 2017 11:05:27 +0000 (05:05 -0600)]
bootstage: Use rec_count as the array index
At present bootstage has a large array with all possible bootstage IDs
recorded. It adds times to the array element indexed by the ID. This is
inefficient because many IDs are not used during boot. We can save space
by only recording those IDs which actually have timestamps.
Update the array to use a record count, which increments with each
addition of a new timestamp. This takes longer to record a time, since it
may involve an array search. Such a search may be particularly expensive
before relocation when the CPU is running slowly or the cache is off. But
at that stage there should be very few records.
Simon Glass [Mon, 22 May 2017 11:05:26 +0000 (05:05 -0600)]
bootstage: Fix up code style and comments
There are several code style and comment nits. Fix them and also remove
the comment about passing bootstage to the kernel being TBD. This is
already supported.
Simon Glass [Mon, 22 May 2017 11:05:25 +0000 (05:05 -0600)]
bootstage: Convert to use malloc()
At present bootstage uses the data section of the image to store its
information. There are a few problems with this:
- It does not work on all boards (e.g. those which run from flash before
relocation)
- Allocated strings still point back to the pre-relocation data after
relocation
Now that U-Boot has a pre-relocation malloc() we can use this instead,
with a pointer to the data in global_data. Update bootstage to do this and
set up an init routine to allocate the memory.
Now that we have a real init function, we can drop the fake 'reset' record
and add a normal one instead.
Note that part of the problem with allocated strings remains. They are
reallocated but this will only work where pre-relocation memory is
accessible after relocation.
Simon Glass [Mon, 22 May 2017 11:05:23 +0000 (05:05 -0600)]
bootstage: Require timer_get_boot_us() to be defined
At present we provide a default version of this function for use by
bootstage. However it uses the system timer and therefore likely requires
driver model. This makes it impossible to time driver-model init.
Drop the function and require boards to provide their own. Add a sandbox
version also. There is a default implememtation in lib/time.c for boards
which use CONFIG_SYS_TIMER_COUNTER.
Tom Rini [Thu, 18 May 2017 21:03:07 +0000 (17:03 -0400)]
cmd/elf.c: Support passing arguments with bootelf
The bootelf command could, but does not, pass additional arguments along
on the command line. Make do_bootelf consume bootelf/flags/address as
needed and then pass along anything else to the ELF application we've
launched.
Reported-by: Thomas Doerfler <thomas.doerfler@embedded-brains.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Patrice Chotard [Thu, 18 May 2017 07:58:00 +0000 (09:58 +0200)]
reset: sti: add deassert counter in reset channel descriptor
This deassert counter allow to manage "shared" reset lines
encountered in some specific case. On STiH410 SoC, DWC3,
EHCI and OHCI are all using a respective PHY, but all of
these PHYs shared a "global" reset.
Currently, during command "usb stop", all host controller are
stopped (XHCI, EHCI and OHCI). XHCI is first shutdowned, which
means that PHY global reset is asserted. Then EHCI is shutdowned,
but its PHY reset has already been asserted which make handshake()
call failed in ehci_shutdown().
This counter allows to really assert a reset lines only when the
"last" user is asserting it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 14:23:09 +0000 (08:23 -0600)]
common: arm: davinci: Move header file out of common
We should not have an arch-specific header file in common.h. Instead, use
the asm/hardware.h header to provide the required declarations, and drop
the common.h changes.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 14:23:05 +0000 (08:23 -0600)]
common: powerpc: Move arch-specific headers
Set up a new asm/ppc.h header file to hold this arch-specific stuff. It
should not be in common.h. It probably should be refactored to use
asm/arch instead, but that is a job for the maintainer.
Tom Rini [Tue, 16 May 2017 18:46:40 +0000 (14:46 -0400)]
t81xx: Migrate TI81XX/TI816X/TI814X symbols to Kconfig
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX. It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.
Tom Rini [Tue, 16 May 2017 18:46:39 +0000 (14:46 -0400)]
ti816x: Modernize the defconfig
- Switch to using <configs/ti_armv7_omap.h> and family. This lets us
drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.
Tom Rini [Tue, 16 May 2017 18:46:36 +0000 (14:46 -0400)]
ti816x_evm: Disable CONFIG_USE_PRIVATE_LIBGCC
On this platform, we can trace a general failure to boot to enabling /
disabling this option. When this is enabled, we go off into the
weeds during SPL and are unable to talk with the SD card and
mmc_initialize() fails.
projects / u-boot / log