Felix Brack [Mon, 27 Nov 2017 08:14:16 +0000 (09:14 +0100)]
power: extend prefix match to regulator-name property
This patch extends pmic_bind_children prefix matching. In addition to
the node name the property regulator-name is used while trying to match
prefixes. This allows assigning different drivers to regulator nodes
named regulator@1 and regulator@10 for example.
I have discarded the idea of using other properties then regulator-name
as I do not see any benefit in using property compatible or even
regulator-compatible. Of course I am open to change this if there are
good reasons to do so.
Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Fri, 24 Nov 2017 17:37:58 +0000 (18:37 +0100)]
dm: reset: have the reset-command perform a COLD reset
The DM version of do_reset has been issuing a warm-reset, which (on
some platforms keeps GPIOs and other parts of the platform active).
This may cause unintended behaviour, as calling do_reset usually
indicates a desire to reset the board/platform and not just the CPU.
This changes do_reset to always request a COLD reset.
Note that programmatic uses can still invoke a WARM reset through
reset_cpu() or using sysreset_walk().
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 14 Nov 2017 01:55:06 +0000 (18:55 -0700)]
binman: tegra: Convert to use binman
Update tegra to use binman for image creation. This still includes the
current Makefile logic, but a later patch will remove this. Three output
files are created, all of which combine
SPL and U-Boot:
u-boot-tegra.bin - standard image
u-boot-dtb-tegra.bin - same as u-boot-tegra.bin
u-boot-nodtb-target.bin - includes U-Boot without the appended device tree
The latter is useful for build systems where the device is appended later,
perhaps after being modified.
Simon Glass [Tue, 14 Nov 2017 01:55:04 +0000 (18:55 -0700)]
binman: Add binman support to spl_ram.c
SPL supports reading U-Boot from a RAM location. At present this is
hard-coded to the U-Boot text base address. Use binman to allow this to
come from the image file, if binman is used.
Simon Glass [Tue, 14 Nov 2017 01:55:03 +0000 (18:55 -0700)]
binman: Add binman symbol support to SPL
Allow SPL to access binman symbols and use this to get the address of
U-Boot. This falls back to CONFIG_SYS_TEXT_BASE if the binman symbol
is not available.
Simon Glass [Tue, 14 Nov 2017 01:55:01 +0000 (18:55 -0700)]
binman: Support accessing binman tables at run time
Binman construct images consisting of multiple binary files. These files
sometimes need to know (at run timme) where their peers are located. For
example, SPL may want to know where U-Boot is located in the image, so
that it can jump to U-Boot correctly on boot.
In general the positions where the binaries end up after binman has
finished packing them cannot be known at compile time. One reason for
this is that binman does not know the size of the binaries until
everything is compiled, linked and converted to binaries with objcopy.
To make this work, we add a feature to binman which checks each binary
for symbol names starting with '_binman'. These are then decoded to figure
out which entry and property they refer to. Then binman writes the value
of this symbol into the appropriate binary. With this, the symbol will
have the correct value at run time.
Macros are used to make this easier to use. As an example, this declares
a symbol that will access the 'u-boot-spl' entry to find the 'pos' value
(i.e. the position of SPL in the image):
This converts to a symbol called '_binman_u_boot_spl_prop_pos' in any
binary that includes it. Binman then updates the value in that binary,
ensuring that it can be accessed at runtime with:
Simon Glass [Tue, 14 Nov 2017 01:55:00 +0000 (18:55 -0700)]
binman: Support enabling debug in tests
The elf module can provide some debugging information to assist with
figuring out what is going wrong. This is also useful in tests. Update the
-D option so that it is passed through to tests as well.
Simon Glass [Tue, 14 Nov 2017 01:54:58 +0000 (18:54 -0700)]
binman: Add tests binaries with binman symbols
For testing we need to build some ELF files containing binman symbols. Add
these to the Makefile and check in the binaries:
u_boot_binman_syms - normal, valid ELF file
u_boot_binman_syms_bad - missing the __image_copy_start symbol
u_boot_binman_syms_size - has a binman symbol with an invalid size
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Alexey Brodkin [Sun, 10 Dec 2017 17:55:44 +0000 (20:55 +0300)]
gpio/hsdk: Depend on DM_GPIO instead of simple DM
This driver really is DM GPIO one and so we need to have a correct
dependency, because DM alone doesn't provide required for CMD_GPIO
call and we're seeing build failures like this:
---------------------->8---------------------
cmd/built-in.o: In function 'do_gpio':
.../cmd/gpio.c:188: undefined reference to 'gpio_request'
...
---------------------->8---------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Eugeniy Paltsev <paltsev@synopsys.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Wed, 6 Dec 2017 05:16:34 +0000 (14:16 +0900)]
ARM: uniphier: use FIELD_PREP for PLL settings
It is tedious to define both mask and bit-shift. <linux/bitfield.h>
provides a convenient way to get access to register fields with a
single shifted mask.
Eugeniy Paltsev [Sun, 10 Dec 2017 18:20:08 +0000 (21:20 +0300)]
ARC: clk: introduce HSDK CGU clock driver
Synopsys HSDK clock controller generates and supplies clocks to various
controllers and peripherals within the SoC.
Each clock has assigned identifier and client device tree nodes can use
this identifier to specify the clock which they consume. All available
clocks are defined as preprocessor macros in the
dt-bindings/clock/snps,hsdk-cgu.h header and can be used in device
tree sources.
dcache_exists, icache_exists, slc_exists and ioc_exists global
variables in "arch/arc/lib/cache.c" remain uninitialized if
SoC doesn't have corresponding HW.
This happens because we use the next constructions for their
definition and initialization:
-------------------------->>---------------------
int ioc_exists __section(".data");
if (/* condition */)
ioc_exists = 1;
-------------------------->>---------------------
That's quite a non-trivial issue as one may think of it.
The point is we intentionally put those variables in ".data" section
so they might survive relocation (remember we initilaize them very early
before relocation and continue to use after reloaction). While being
non-initialized and not explicitly put in .data section they would end-up
in ".bss" section which by definition is filled with zeroes.
But since we place those variables in .data section we need to care
about their proper initialization ourselves.
Also while at it we change their type to "bool" as more appropriate.
Eugeniy Paltsev [Sat, 21 Oct 2017 12:35:12 +0000 (15:35 +0300)]
ARC: HSDK: Fixup DW SDIO CIU frequency to 50000000Hz
DW SDIO controller has external CIU clock divider controlled via
register in the SDIO IP. Due to its unexpected default value
(we expected it to divide by 1 but in reality it divides by 8)
SDIO IP uses wrong CIU clock (it should be 100000000Hz but actual
is 12500000Hz) and works unstable (see STAR 9001204800).
So increase SDIO CIU frequency from actual 12500000Hz to 50000000Hz
by switching from the default divisor value (div-by-8) to the
minimum possible value of the divisor (div-by-2) in HSDK platform
code.
Eugeniy Paltsev [Mon, 16 Oct 2017 12:15:33 +0000 (15:15 +0300)]
ARC: add asm/gpio.h to fix compilation error with CONFIG_CMD_GPIO
With CONFIG_CMD_GPIO compilation reports error:
-------------------------->8---------------------
common/cmd_gpio.c:13:22: fatal error: asm/gpio.h: No such file or directory
#include <asm/gpio.h>
^
-------------------------->8---------------------
rockchip: rk3399-puma: preserve leading zeros in serial#
Linux preserves leading zeros in /proc/cpuinfo, so we
should as well.
Otherwise we have the situation that
/sys/firmware/devicetree/base/serial-number
and /proc/cpuinfo disagree in Linux.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
York Sun [Thu, 7 Dec 2017 21:16:07 +0000 (13:16 -0800)]
armv8: fix gd after relocation
Commit 21f4486faa5d ("armv8: update gd after relocate") sets x18
without checking the return value of spl_relocate_stack_gd().
Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: York Sun <york.sun@nxp.com> CC: Kever Yang <kever.yang@rock-chips.com> CC: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Mon, 4 Dec 2017 20:48:22 +0000 (13:48 -0700)]
usb: Correct use of debug()
With clang this gives a warning because hubsts appears to be used before
it is set, even if ultimately it is not used. Simplify the code to avoid
this problem.
Simon Glass [Mon, 4 Dec 2017 20:48:21 +0000 (13:48 -0700)]
mtdparts: Correct use of debug()
The debug() macro now evaluates its expression so does not need #ifdef
protection. In fact the current code causes a warning with the new log
implementation. Adjust the code to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 4 Dec 2017 20:48:19 +0000 (13:48 -0700)]
Revert "sandbox: Drop special case console code for sandbox"
While sandbox works OK without the special-case code, it does result in
console output being stored in the pre-console buffer while sandbox starts
up. If there is a crash or a problem then there is no indication of what
is going on.
For ease of debugging it seems better to revert this change also.
Simon Glass [Mon, 4 Dec 2017 20:48:17 +0000 (13:48 -0700)]
Revert "sandbox: remove os_putc() and os_puts()"
While sandbox works OK without the special-case code, it does result in
console output being stored in the pre-console buffer while sandbox starts
up. If there is a crash or a problem then there is no indication of what
is going on.
For ease of debugging it seems better to revert this change.
Alan Ott [Wed, 29 Nov 2017 03:25:24 +0000 (22:25 -0500)]
i2c: at91_i2c: remove the .probe_chip function
The .probe_chip function is supposed to probe an i2c device on the bus to
determine whether a device is answering to a particular address.
at91_i2c_probe_chip() did not do anything resembling this and always
returned 0.
It looks as though at91_i2c_probe_chip() was intended to be a .probe
function for the controller, as it was copied-and-pasted to become
at91_i2c_probe() in 0bc8f640a4d7ed.
Removing the at91_i2c_probe_chip() function makes the higher layer
(i2c_probe_chip()) try a zero-length read transfer to test for the
presence of a device instead, which does work.
Signed-off-by: Alan Ott <alan@softiron.com> Acked-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Alan Ott [Wed, 29 Nov 2017 03:25:23 +0000 (22:25 -0500)]
i2c: at91_i2c: Wait for TXRDY after sending the first byte
The driver must wait for TXRDY after each byte is pushed into
the i2c FIFO before pushing the next byte. Previously this was
not done for the first byte, causing a race condition with zeros
sometimes being sent for the next byte (which is typically the
first actual data byte).
Signed-off-by: Alan Ott <alan@softiron.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Add fall back option, to boot from NOR/QSPI/SD for LS1043, LS1046,
LS1021 in case of distro boot failure.
For LS1046, add kernel validation in case of secure boot in sd_bootcmd
and qspi_bootcmd. For LS1043 and LS1021, add kernel validation in case
of secure boot in sd_bootcmd, qspi_bootcmdand nor_bootcmd.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
armv8: fsl-layerscape: Add support of disabling core prefetch
Instruction prefetch feature is by default enabled during core
release. This patch add support of disabling instruction prefetch
by setting core mask in PPA. Here each core mask bit represents a
core and prefetch is disabled at the time of core release.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yogesh Gaur [Wed, 15 Nov 2017 06:29:31 +0000 (11:59 +0530)]
driver: net: fsl-mc: flib changes for MC 10.3.0
Existing MC driver framework is based on MC-9.x.x flib. This patch
migrates MC obj (DPBP, DPNI, DPRC, DPMAC etc) to use latest MC flib
which is MC-10.3.0.
Changes introduced due to migration:
1. To get OBJ token, pair of create and open API replaces create APIs
2. Pair of close and destroy APIs replaces destroy APIs
3. For version read, get_version APIs replaces get_attributes APIs
4. dpni_get/reset_statistics APIs replaces dpni_get/set_counter APIs
5. Simplifies struct dpni_cfg and removes dpni_extended_cfg struct
6. Single API dpni_get_buffer_layout/set_buffer_layout replaces
dpni_get_rx/set_rx, tx related, tx_conf_buffer_layout related APIs.
New API takes a queue type as an argument.
7. Similarly dpni_get_queue/set_queue replaces
dpni_get_rx_flow/set_rx_flow , tx_flow related, tx_conf related
APIs
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Ashish Kumar [Thu, 23 Nov 2017 09:03:49 +0000 (14:33 +0530)]
armv8: ls1088a: Unset USE_BOOTCOMMAND in defconfig
Unset USE_BOOTCOMMAND for all ls1088 defconfig files to fix
redefinition error. USE_BOOTCOMMAND was introduced in commit b6251db8c3f ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Tue, 5 Dec 2017 18:57:54 +0000 (10:57 -0800)]
powerpc: mpc85xx: Fix static TLB table for SDRAM
Most predefined TLB tables don't have memory coherence bit set for
SDRAM. This wasn't an issue before invalidate_dcache_range() function
was enabled. Without the coherence bit, dcache invalidation doesn't
automatically flush the cache. The coherence bit is already set when
dynamic TLB table is used. For some boards with different SPL boot
method, or with legacy fixed setting, this bit needs to be set in
TLB files.
Ran Wang [Mon, 27 Nov 2017 02:51:55 +0000 (10:51 +0800)]
powerpc/p1_p2_rdb_pc: Fix endian access issue on EHCI intinalization
This issue is exposed after commit 9000eddbae0d ("drivers/usb/ehci:
Use platform-specific accessors"), the wrong endianness of EHCI
controller programing will cause USB function down.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 27 Nov 2017 02:51:54 +0000 (10:51 +0800)]
powerpc/T104xRDB: Fix endian access issue on EHCI intinalization
This issue is exposed after commit 9000eddbae0d ("drivers/usb/ehci:
Use platform-specific accessors"), the wrong endianness of EHCI
controller programing will cause USB function down.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Philipp Tomsich [Mon, 4 Dec 2017 16:04:02 +0000 (17:04 +0100)]
tools: omapimage: fix corner-case in byteswap path
Since commit 2614a208471e ("common: command: tempory buffer should
have size of command line buf"), there have been consistent Travis CI
failures on my builds (interestingly not for Tom, even though building
the same commit id) due to a SEGV in building the byteswapped
omapimage:
arm: pcm051_rev3
make[2]: *** [MLO.byteswap] Error 139
^^^ error code for a SEGV
Turns out that the word-based byte-swapping loop in omapimage.c is to
blame. With the loop condition
while (swapped <= (sbuf->st_size / sizeof(uint32_t)))
there had been one-too-many iterations for all file sizes divisible by
the sizeof(uint32_t). I.e. we had 1 iteration for 0 bytes (and also 1
through 3 bytes) and 2 iterations at 4 bytes... clearly overshooting
on 0 and 4 bytes.
This commit fixes the calculation of an up-rounded word-count and
makes sure to keep the zero-based loop-counter below the number of
words to be processed.
References: 2614a20 ("common: command: tempory buffer should have size of command line buf") Fixes: 79b9ebb ("omapimage: Add support for byteswapped SPI images") Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Alexander Graf [Mon, 4 Dec 2017 15:33:51 +0000 (16:33 +0100)]
efi_stub: Use efi_uintn_t
Commit f5a2a93892f ("efi_loader: consistently use efi_uintn_t in boot
services") changed the internal EFI API header without adapting its existing
EFI stub users. Let's adapt the EFI stub as well.
Fixes: f5a2a93892f ("efi_loader: consistently use efi_uintn_t in boot services") Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Peng Fan [Thu, 30 Nov 2017 02:07:07 +0000 (10:07 +0800)]
scripts: spl: fix typo
Typo fix: CONIFG->CONFIG
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Derald D. Woods [Wed, 29 Nov 2017 03:28:55 +0000 (03:28 +0000)]
omap3: evm: Explicitly use DISTRO_DEFAULTS features at startup
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:1 zImage and run mmcbootz
[fallback 2] Check MMC 0:1 uImage and run mmcboot
[fallback 3] Check NAND partitions and run nandboot
If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is
followed.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Neil Armstrong [Mon, 27 Nov 2017 09:35:46 +0000 (10:35 +0100)]
ARM: arch-meson: build memory banks using reported memory from registers
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
projects / u-boot / log