arch/powerpc: Fix mapping of Freescale SerDes protocols
The number of supported serdes protocols on Freescale SoCs
has increased over time. Until now, an u64 variable have been
initialized on boot with the configured protocols. However,
since this number has increased (enum srds_prtcl has more
than 64 values), 64 bits are no longer sufficient to hold track
of all the configured protocols.
This patch replaces the u64 map values with static arrays.
To keep track of the number of serdes protocols, the
SERDES_PRCTL_COUNT vale has been added at the end of
enum srds_prtcl. This value must always be the last one.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
U-boot assumes that all FMAN ports have a PHY. Some SoCs (like T1040)
have fixed links. This means that the ports are connected MAC to MAc
and there is no Ethernet PHY attatched. This patch initializes a
FMAN MAC even if it doesn't have a PHY attached.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Tue, 30 Dec 2014 10:32:04 +0000 (18:32 +0800)]
phylib: add support for aquantia PHYs
This patch supports AQ1202, AQ2104, AQR105 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
tang yuantian [Thu, 18 Dec 2014 02:26:34 +0000 (10:26 +0800)]
mpc85xx: clean up the old deep sleep framework
All the boards that support deep sleep feature are converted
to deep sleep generic board interface. The old interface which
support non-generic board is not used anymore. So clean it up.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Ruchika Gupta [Wed, 10 Dec 2014 06:22:50 +0000 (11:52 +0530)]
powerpc: mpc85xx: Add dummy gpio.h to enable CONFIG_OF_CONTROL
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h>.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.
This commit adds a dummy <asm/arch/gpio.h> to support OF_CONTROL
for mpc85xx platform. A file mpc85xx_gpio.h exists in
arch/powerpc/include/asm. The defintions in that file conflict
with the ones in asm-generic/gpio.h. Hence a dummy header file
has been added. This will be removed after FDT-GPIO stuff is
fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Masahiro Yamada [Thu, 15 Jan 2015 08:13:24 +0000 (17:13 +0900)]
powerpc: 74xx_7xx: remove 74xx_7xx cpu support
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Nye Liu <nyet@zumanetworks.com> Cc: Roy Zang <tie-fei.zang@freescale.com>
Simon Glass [Tue, 2 Dec 2014 00:34:07 +0000 (17:34 -0700)]
buildman: Add an option to write the full build output
Normally buildman runs with 'make -s' meaning that only errors and warnings
appear in the log file. Add a -V option to run make in verbose mode, and
with V=1, causing a full build log to be created.
Simon Glass [Tue, 2 Dec 2014 00:34:06 +0000 (17:34 -0700)]
buildman: Add the option to download toolchains from kernel.org
The site at https://www.kernel.org/pub/tools/crosstool/ is a convenient
repository of toolchains which can be used for U-Boot. Add a feature to
download and install a toolchain for a selected architecture automatically.
It isn't clear how long this site will stay in the current place and
format, but we should be able to rely on bug reports if it changes.
Suggested-by: Marek VaĊĦut <marex@denx.de> Suggested-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 2 Dec 2014 00:34:00 +0000 (17:34 -0700)]
buildman: Add an option to use the full tool chain path
In some cases there may be multiple toolchains with the same name in the
path. Provide an option to use the full path in the CROSS_COMPILE
environment variable.
Note: Wolfgang mentioned that this is dangerous since in some cases there
may be other tools on the path that are needed. So this is set up as an
option, not the default. I will need test confirmation (i.e. that this
commit fixes a real problem) before merging it.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Steve Rae <srae@broadcom.com>
Simon Glass [Tue, 2 Dec 2014 00:33:57 +0000 (17:33 -0700)]
buildman: Allow specifying a range of commits to build
Adjust the -b flag to permit a range expression as well as a branch.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Simon Glass [Tue, 2 Dec 2014 00:33:56 +0000 (17:33 -0700)]
buildman: Don't remove entire output directory when testing
When running tests the output directory is often wiped. This is only safe if
a branch is being built. The output directory may contain other things
besides the buildman test output.
Simon Glass [Tue, 2 Dec 2014 00:33:55 +0000 (17:33 -0700)]
buildman: Add an option to flatten output directory trees
When building current source for a single board, buildman puts the output
in <output_dir>/current/current/<board>. Add an option to make it use
<output_dir>/<board> instead. This removes the unnecessary directories
in that case, controlled by the --no-subdirs/-N option.
Suggested-by: Tom Rini <trini@ti.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 2 Dec 2014 00:33:54 +0000 (17:33 -0700)]
buildman: Try to guess the upstream commit
Buildman normally obtains the upstream commit by asking git. Provided that
the branch was created with 'git checkout -b <branch> <some_upstream>' then
this normally works.
When there is no upstream, we can try to guess one, by looking up through
the commits until we find a branch. Add a function to try this and print
a warning if buildman ends up relying on it.
Also update the documentation to match.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Wolfgang Denk <wd@denx.de>
Simon Glass [Tue, 2 Dec 2014 00:33:53 +0000 (17:33 -0700)]
buildman: Don't prune output space for 'current source' build
This is not needed since we always do a full (non-incremental) build. Also
it might be dangerous since it will try to delete everything below the
base directory.
Alexey Brodkin [Tue, 13 Jan 2015 15:49:01 +0000 (18:49 +0300)]
Kconfig: move CONFIG_SYS_CLK_FREQ to Kconfig
It makes sense to specify CONFIG_SYS_CLK_FREQ in "configs/xx_defconfig"
instead of "include/configs/xxx.h" because then header will be reusable
across boards with different CPU clocks.
Also this nice to have an ability for end user to tune this value
himself via "menuconfig".
For now I'm only applying this change to all ARC configs because
otherwise scope of change will be huge.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Hans de Goede <hdegoede@redhat.com>
cc: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
Masahiro Yamada [Thu, 8 Jan 2015 10:23:35 +0000 (19:23 +0900)]
spl: spl_nor: surround Linux-load code with #ifdef CONFIG_SPL_OS_BOOT
If CONFIG_SPL_NOR_SUPPORT is defined, spl_nor_load_image() requires
spl_start_uboot(), CONFIG_SYS_OS_BASE, CONFIG_SYS_SPL_ARGS_ADDR,
CONFIG_SYS_FDT_BASE to be defined even if users just want to run
U-Boot, not Linux. This is inconvenient.
This patch is following the codying style of common/spl/spl_nand.c.
Simon Glass [Tue, 2 Dec 2014 20:17:37 +0000 (13:17 -0700)]
bootm: Factor out common parts of image decompression code
Adjust the code so that the error reporting can all be done at the end,
and is the same for each decompression method. Try to detect when
decompression fails due to lack of space. Keep the behaviour of
resetting on failure even though there should be no memory corruption
now.
Simon Glass [Tue, 2 Dec 2014 20:17:31 +0000 (13:17 -0700)]
sandbox: Correct ordering of 'sb save' commands
Prior to commit d455d87 there was an inconsistency between the position of
the 'address' parameter in 'sb load' and 'sb save'. This was corrected but
it broke some tests. Fix the tests and also the help for 'sb save'.
Simon Glass [Tue, 2 Dec 2014 20:17:30 +0000 (13:17 -0700)]
bootm: Move compression progress/error messages into a function
This code is repeated in several places, and does not detect a common
fault where the image is too large. Move it into its own function and
provide a more helpful messages in this case, for compression schemes
which support this.
Simon Glass [Tue, 2 Dec 2014 20:17:29 +0000 (13:17 -0700)]
lzma: fix buffer bound check error further
Commit 4d3b8a0d fixed a problem with lzma decompress where it would
run out of bytes to decompress. The algorithm needs to know how many
uncompressed bytes it is expected to produce.
However, the fix introduced a potential buffer overrun, and causes
the compression test to fail (test_compression command in sandbox).
The correct fix seems to be to use the minimum of the expected number
of uncompressed bytes and the amount of output space available. That
way things work normally when there is enough space, and return an
error (without overrunning available space) when there is not.
Signed-off-by: Antonios Vamporakis <ant@area128.com> CC: Kees Cook <keescook@chromium.org> CC: Simon Glass <sjg@chromium.org> CC: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> CC: Luka Perkov <luka@openwrt.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Wed, 14 Jan 2015 03:35:24 +0000 (12:35 +0900)]
README.scrapyard: fill commit and date fields
This commit was generated by the following command:
scripts/fill_scrapyard.py
The commit-ID of CPCIISER4 removal has been fixed by hand because
the board was removed by commit 370572601027 (ppc4xx: remove CPCIISER4
board), but it was added to README.scrapyard by commit 9a4018e09a2f
(ppc4xx: remove DP405 board).
Hans de Goede [Sun, 11 Jan 2015 18:33:35 +0000 (19:33 +0100)]
sunxi: usbc: Add support for usb-vbus0 controller by axp drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 11 Jan 2015 18:58:03 +0000 (19:58 +0100)]
sunxi: axp221: Add support for controlling the drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, add axp_drivebus_enable() and _disable() functions to set
the pin in output mode and control it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 11 Jan 2015 18:43:56 +0000 (19:43 +0100)]
sunxi: axp221: Protect axp221_init against multiple calls
The voltage setting code knows it needs to call axp221_init before calling
the various voltage setting functions.
But users of axp utility functions like axp221_get_sid() do not know this,
so the utility functions always call axp221_init() to ensure that the
p2wi / rsb setup magic has been done.
Since doing this repeatedly is quite expensive, add a check to axp221_init
so that it only does the initialization once.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Chen-Yu Tsai [Mon, 12 Jan 2015 10:02:12 +0000 (18:02 +0800)]
sunxi: Hummingbird_A31_defconfig: Enable VGA output through external DAC
The Hummingbird A31 uses an external DAC connected to the LCD0 outputs
for the on board VGA output. The DAC has a power control that's toggled
by GPIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 10:02:10 +0000 (18:02 +0800)]
sunxi: video: Allow external DACs for VGA on platforms without TV encoders
Using an external DAC for VGA output was available on sun5i. Since
some other SoCs don't have a builtin TV encoder, but might have
use for a VGA output, enable the option for the platforms that
don't have TV encoders.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This allows to always have a complete log on the VGA/HDMI/LCD console.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
console: Use pre-console buffer to get complete log on all consoles
Currently the pre-console buffer can accumulate early log messages
and flush them to the serial console as soon as it becomes available.
This patch just adds one more pre-console buffer flushing point and
does all the same for the other consoles too. This is particularly
useful for the vga/hdmi/lcd console, where we can see all the older
messages now (except for the log messages from SPL).
Naturally, we don't want to get an extra copy of the log messages
on the serial console again at the second flushing point, so the
serial console has to be explicitly filtered out.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Jan Kiszka [Wed, 31 Dec 2014 12:46:42 +0000 (13:46 +0100)]
sun7i: Move psci_arch_init close to text_end
"adr rX, text_end" only works if the label is close. Adding further code
to the other functions will prevent this. So move the containing
function close to label. No functional change.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Jan Kiszka [Wed, 31 Dec 2014 12:46:40 +0000 (13:46 +0100)]
sun7i: Add support for taking CPUs offline via PSCI
Based on the original version by Marc Zyngier. It adds a psci_cpu_off
implementation for the A20 SoC. The mechanism works by first preparing
the calling CPU to go offline (disable and flush cache, disable SMP),
then requesting CPU 0 to pull the plug. The request is sent as FIQ on
SGI15.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Zoltan HERPAI [Tue, 6 Jan 2015 00:09:18 +0000 (01:09 +0100)]
sunxi: add Linksprite pcDuino v1/v2 support
Add support for a sun4i board built by Linksprite. This addition covers
both v1 and v2 versions. As the board has been working with 408MHz memory
setting in the u-boot-sunxi branch, and has been proven to be running stable
during my tests as well, a respective new DRAM config file is added as well.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 28 Dec 2014 08:13:21 +0000 (09:13 +0100)]
sunxi: video: Add a hpd_delay parameter to configure hpd delay
In some extreme cases it may be necessary to wait 1.5 seconds or more for a hpd
signal to show up (and be able to read edid info), but we do not want to
penalize all headless boots with an extra second boot delay, so add a hpd_delay
parameter which can be set through the video-mode env. variable.
While at it raise the default from 300ms to 500ms as 300 may very well be too
low in many cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 24 Dec 2014 18:50:11 +0000 (19:50 +0100)]
sunxi: video: Use sunxi_lcdc_get_clk_delay to calculate tcon1 delay
Use sunxi_lcdc_get_clk_delay to calculate tcon1 delay instead of hardcoding
it to 30. We will still end up using 30 for most modes, but for e.g. 800x600
this makes a (small) difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Having both a sunxi_display.enabled variable and
sunxi_display.monitor == sunxi_monitor_none duplicates state, use
sunxi_display.monitor = sunxi_monitor_none when ever we do not have a display.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable VGA output on the A13-OLinuXino and A13-OLinuXinoM now that we've
support for it.
Also add LCD timing and gpio info for the Olimex 7" LCD module. We can safely
put this in the default config on this boards, since by default we will always
use VGA, and the LCD timing info will only get used if the user explicitly
sets monitor=lcd in the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 24 Dec 2014 15:08:30 +0000 (16:08 +0100)]
sunxi: sunxi-common.h: Reduce bootm_size to take the framebuffer into account
Before video output support can be enabled on the A13-OLinuXinoM, bootm_size
must first be reduced to take into account that the framebuffer is shaved of
the top of the DRAM. For other boards this is not an issue since bootm was set
to 256M and all boards have at least 512M except for the A13-OLinuXinoM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 21 Dec 2014 15:27:45 +0000 (16:27 +0100)]
sunxi: video: Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.
While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 21 Dec 2014 13:49:34 +0000 (14:49 +0100)]
sunxi: video: Prepare for lcd support
Refactor sunxi_mode_set into a bunch of helpers, and make it do a switch
case on sunxi_display.monitor to decide what to do.
Also rename sunxi_lcdc_mode_set to sunxi_lcdc_tcon1_mode_set, as it sets the
timings for tcon1, and for lcd support we need a similar function operating
on tcon0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a sunxi_monitor enum and parse the monitor option string into this enum
once, rather then doing strcmp-s on it in various places. This also adds
checking for it being a valid value.
This also adds new "none" and "lcd" values in preparation for lcd support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 24 Dec 2014 18:34:38 +0000 (19:34 +0100)]
sunxi: gpio: Add support for gpio pins on the AXP209 pmic
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
projects / u-boot / log