John Keeping [Fri, 15 Jul 2016 16:33:23 +0000 (17:33 +0100)]
rockchip: sdram: Fix register layout for Linux
The ChromeOS kernel reads the RAM settings from PMU_SYS_REG2 and expects
the bootloader to store the necessary information there. We're using
the same register to pass the same information between the SPL and
U-Boot but in a slightly different format.
Change this to use the format expected by the Linux DMC driver so that
the system doesn't hang in Linux by misconfiguring the RAM.
This is almost the same as commit b5788dc ("rockchip: rk3288: correct
sdram setting") which was reverted in commit b525556 ("Revert "rockchip:
rk3288: correct sdram setting"") but parenthese have been added to apply
the mask correctly when reading the "bw" setting and a couple of minor
style issues have been fixed to keep check_patch.pl happy.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Mon, 18 Jul 2016 09:00:58 +0000 (17:00 +0800)]
mmc: rockchip: add SDHCI driver support for rockchip soc
Rockchip rk3399 using arasan sdhci-5.1 controller.
This patch add the controller support to enable mmc device
with full driver-model support, tested on rk3399 evb board.
According to my test result, this driver should be OK,
the command "part list mmc 0" can result in a right output,
but all the mmc command failed like this:
=> mmc info
No MMC device available
Command failed, result=1
The result of get_mmc_num in cmd/mmc.c is always 0?
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Tue, 19 Jul 2016 13:16:59 +0000 (21:16 +0800)]
ARM64: rockchip: add support for rk3399 SoC based evb
RK3399 is a SoC from Rockchip with dual-core Cortex-A72
and quad-core Cortex-A53 CPU. It supports two USB3.0
type-C ports and two USB2.0 EHCI ports. Other interfaces
are very much like RK3288, the DRAM are 32bit width address
and support address from 0 to 4GB-128MB range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Tue, 19 Jul 2016 13:16:58 +0000 (21:16 +0800)]
dts: add support for Rockchip rk3399 soc
These files are from kernel upstream:
"649a371 Add linux-next specific files for 20160616"
with some modification need by U-Boot:
- chosen with stdout-path to uart2.
- add clock-frequency for uart2
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 17 Jul 2016 21:23:17 +0000 (15:23 -0600)]
rockchip: Use rockchip_get_clk() to obtain the SoC clock
The current code picks the first available clock. In U-Boot proper this is
the oscillator device, not the SoC clock device. As a result the HDMI display
does not work.
Fix this by calling rockchip_get_clk() instead.
Fixes: 135aa950 (clk: convert API to match reset/mailbox style) Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Simon Glass [Sun, 17 Jul 2016 21:23:16 +0000 (15:23 -0600)]
rockchip: Add a way to obtain the main clock device
On Rockchip SoCs we typically have a main clock device that uses the Soc
clock driver. There is also a fixed clock for the oscillator. Add a function
to obtain the core clock.
Simon Glass [Sun, 17 Jul 2016 21:23:15 +0000 (15:23 -0600)]
dm: core: Add a way to find a device by its driver
Some SoCs have a single clock device. Provide a way to find it given its
driver name. This is handled by the linker so will fail if the name is not
found, avoiding strange errors when names change and do not match. It is
also faster than a string comparison.
The function is very specific to the rk3288 in its arguments
referencing the rk3288 cru and grf and every other rockchip soc
has differing cru and grf registers. So make that function naming
explicit.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Glass <sjg@chromium.org>
cosmetic: rockchip: sort socs according to numbers
Having some sort of ordering proofed helpful in a lot of other places
already. So for a larger number of rockchip socs it might be helpful
as well instead of an ever increasing unsorted list.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org>
cosmetic: rockchip: rk3036: pinctrl: fix config symbol naming
Rockchip socs are always named rkxxxx in all places, as also shown
by the naming of the rk3036 pinctrl file itself.
Therefore also name the config symbol according to this scheme.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Glass <sjg@chromium.org>
This path doesn't support the fastboot flash function command entirely.
We will hit "cannot find partition" assertion without specified
partition environment. Define gpt partition layout in specified board
such as firefly-rk3288, then enjoy it!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Invalidate dcache before starting the DMA to ensure coherency. In case
there are any dirty lines from the DMA buffer in the cache, subsequent
cache-line replacements may corrupt the buffer in memory while the DMA
is still going on. Cache-line replacement can happen if the CPU tries to
bring some other memory locations into the cache while the DMA is going
on.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
So far, Rockchip SoCs have two kinds of USB2.0 phy, such as Synopsys and
Innosilicon. This patch applys dwc2 usb driver framework to implement
phy_init() and phy_off() methods for Synopsys phy on Rockchip platform.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 8 Jul 2016 03:30:58 +0000 (11:30 +0800)]
board: move all the rockchip board in one folder
The 'evb_rk3036' and 'kylin' is not a vendor name, let's replace them
to 'rockchip' which is a real _vendor_ name, and meet the architecure
'board/<vendor>/<board-name>/'.
More boards from rockchip like evb_rk3288, evb_rk3399 will comes later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Eddie Cai <eddie.cai.kernel@gmail.com>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
rockchip: add option to change method of loading u-boot
If we would like to boot from SD card, we have to implement mmc driver
in SPL stage, and get a slightly large SPL binary. Rockchip SoC's
bootrom code has the ability to load spl and u-boot, then boot.
If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to
bootrom in board_init_f(), then bootrom loads u-boot binary.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip: Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 25 Jul 2016 22:18:15 +0000 (18:18 -0400)]
sandbox: Migrate CONFIG_I2C_EEPROM
Most users of CONFIG_I2C_EEPROM were migrated to defconfig a while ago,
but sandbox was skipped. Leave it off for sandbox_spl where it does not
build, but does not need to be either.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Fri, 22 Jul 2016 15:22:49 +0000 (09:22 -0600)]
dtoc: Correct the type widening code in fdt_fallback
This code does not match the fdt version in fdt.py. When dtoc is unable to
use the Python libfdt library, it uses the fallback version, which does not
widen arrays correctly.
Fix this to avoid a warning 'excess elements in array initialize' in
dt-platdata.c which happens on some platforms.
Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Rini <trini@konsulko.com>
tools, rsa: Further minor cleanups on top of c236ebd and 2b9ec7
[NOTE: I took v1 of these patches in, and then v2 came out, this commit
is squashing the minor deltas from v1 -> v2 of updates to c236ebd and 2b9ec76 into this commit - trini]
- Added an additional NULL check, as suggested by Simon Glass to
fit_image_process_sig
- Re-formatted the comment blocks
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
[For merging the chnages from v2 back onto v1] Signed-off-by: Tom Rini <trini@konsulko.com>
ARM: am33xx: Always inhibit init/refresh during DDR phy init
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:
The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.
Signed-off-by: Russ Dill <Russ.Dill@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
In certain circumstances it comes in handy to be able to boot into a second
U-Boot. But as of now it is not possible to boot a U-Boot binary that is inside
a FIT image, which is problematic for projects that e.g. need to guarantee a
unbroken chain of trust from SOC all the way into the OS, since the FIT signing
mechanism cannot be used.
This patch adds the capability to load such FIT images.
An example .its snippet (utilizing signature verification) might look
like the following:
commit 1f807a9f32aa ("ARM: keystone2: Refactor MSMC macros to avoid
left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid.
This, in effect disabled DMA coherency for QM PDSP.
Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs,
the #ifdef should been removed in the first place. Do the same.
A feasible way to communicate certain errors for devices that have no
other way of signalling besides LEDs is to flash these LEDs. For errors
in U-Boot, a script that utilizes the led and sleep commands would be a
practicable way, but currently the sleep command can only delay for an
integral amount of seconds, which is too slow to create an easily
noticeable pattern for flashing LEDs.
Therefore, this patch adds support for fractions (down to .001 seconds)
to the sleep command.
The parsing is kept minimal, simplistic and as robust as possible: After
converting the passed string using simple_strtoul and multiplying it
with 1000, we search for the first dot, convert the three characters
after that into a number (if they are not numbers, we ignore the
fractional part and just use the delay we got from simple_strtoul), and
add this number to the delay.
mtd: nand: fix bug writing 1 byte less than page size
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write, although
it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating until the watchdog timeout triggers.
To reproduce the issue on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
Brian Norris [Wed, 15 Jun 2016 19:09:22 +0000 (21:09 +0200)]
mtd: nand: add common DT init code
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
The original commit has been slightly reworked to use the fdtdec_xxx()
helpers (instead of the of_xxxx() ones).
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
Boris Brezillon [Wed, 15 Jun 2016 08:42:18 +0000 (10:42 +0200)]
cmd, nand: add an option to disable the verification when writing in raw mode
Modern NANDs do not guarantee that data written in raw mode will not
contain bitflips just after writing them. This is fine since the number
of bitflips should be rather low and thus fixable by the ECC engine,
but since we are reading data in raw mode to verify if they match the
input data we cannot prevent failures if some bits are flipped.
The option of using standard mode to verify the data is not acceptable
either, since one of the usage of raw mode is to allow flashing images
that do not respect the standard NAND page layout or the default ECC
config (this is the case on Allwinner platforms, where the ROM code
tests several hardcoded configs, which are not necessarily matching the
NAND characteristics).
Add an extension to the nand write.raw command allowing one to disable
the verification step.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: uniphier: use (devm_)ioremap() instead of map_sysmem()
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
ARM: dts: uniphier: renumber serial aliases for Gentil/Vodka boards
On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.
arm: omap5: fix build dependency for secure devices
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
arm: am4x: fix build dependency for secure devices
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM43xx high-security (HS) devices that causes the
build to break when that option is not active. Fix this issue by only
building the u-boot_HS.img target when building U-Boot into an actual
FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
spl: fit: Fix the number of bytes read in raw mode
In raw mode a full sector is to be read even if image covers part of
a sector. Number of sectors are calculated as ROUND_UP(size)/sec_size by FIT
framework. This calculation assumes that image is at the 0th offset of a sector,
which is not true always in FIT case. So, include the image offset while
calculating number of sectors.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
When signing images, we repeatedly call fit_add_file_data() with
successively increasing size values to include the keys in the DTB.
Unfortunately, if large keys are used (such as 4096 bit RSA keys), this
process fails sometimes, and mkimage needs to be called repeatedly to
integrate the keys into the DTB.
This is because fit_add_file_data actually returns the wrong error
code, and the loop terminates prematurely, instead of trying again with
a larger size value.
This patch corrects the return value by fixing the return value of
fdt_add_bignum, fixes a case where an error is masked by a unconditional
setting of a return value variable, and also removes a error message,
which is misleading, since we actually allow the function to fail. A
(hopefully helpful) comment is also added to explain the lack of error
message.
This is probably related to 1152a05 ("tools: Correct error handling in
fit_image_process_hash()") and the corresponding error reported here:
When signing images, we repeatedly call fit_add_file_data() with
successively increasing size values to include the keys in the DTB.
Unfortunately, if large keys are used (such as 4096 bit RSA keys), this
process fails sometimes, and mkimage needs to be called repeatedly to
integrate the keys into the DTB.
This is because fit_add_file_data actually returns the wrong error
code, and the loop terminates prematurely, instead of trying again with
a larger size value.
This patch corrects the return value and also removes a error message,
which is misleading, since we actually allow the function to fail. A
(hopefully helpful) comment is also added to explain the lack of error
message.
This is probably related to 1152a05 ("tools: Correct error handling in
fit_image_process_hash()") and the corresponding error reported here:
Stephen Warren [Mon, 18 Jul 2016 16:07:25 +0000 (10:07 -0600)]
test/py: use absolute dts path in vboot test
Without this, the test fails if the test is run with a cwd other than the
root of the U-Boot source tree.
Fixes: 8729d582595d ("test: Convert the vboot test to test/py") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Jeremy Hunt [Mon, 18 Jul 2016 16:01:02 +0000 (12:01 -0400)]
armv8: spl: Call board_init_r from crt0_64 in SPL
As part of the startup process for boards using the SPL, the
meaning of board_init_f changed such that it should return normally
rather than calling board_init_r directly. (see db910353a126d84fe8dff7a694ea792f50fcfb6a )
This was fixed in 32-bit arm, but broke when SPL was added to
64 bit arm. This fixes crt0_64 so that it calls board_init_r
during the SPL and removes the direct call from board_init_f
from the arm SPL example.
Signed-off-by: Jeremy Hunt <Jeremy.Hunt@DEShawResearch.com> Acked-by: Simon Glass <sjg@chromium.org>
Andreas Fenkart [Sat, 16 Jul 2016 15:06:15 +0000 (17:06 +0200)]
tools/env: reuse fw_getenv in fw_printenv function
Try to avoid adhoc iteration of the environment. Reuse fw_getenv
to find the variables that should be printed. Only use open-coded
iteration when printing all variables.
For backwards compatibility, keep emitting a newline when
printing with value_only.
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Andreas Fenkart [Sat, 16 Jul 2016 15:06:13 +0000 (17:06 +0200)]
tools/env: kernel-doc for fw_printenv, fw_getenv and fw_parse_script
there are two groups of functions:
- application ready tools: fw_setenv/fw_getenv/fw_parse_script
these are used, when creating a single binary containing multiple
tools (busybox like)
- file access like: open/read/write/close
above functions are implemented on top of these. applications
can use those to modify several variables without creating a
temporary batch script file
tested with "./scripts/kernel-doc -html -v tools/env/fw_env.h"
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Tom Rini [Fri, 15 Jul 2016 19:51:40 +0000 (15:51 -0400)]
gdsys: Drop print_fpga_state function
On most platforms the print_fpga_state function is never called. Only
on dlvision-10g do we, so in that case inline it. Drop it from
everywhere else to avoid extra strings.
Stefan Agner [Thu, 14 Jul 2016 00:14:38 +0000 (17:14 -0700)]
tools/env: allow negative offsets
A negative value for the offset is treated as a backwards offset for
from the end of the device/partition for block devices. This aligns
the behavior of the config file with the syntax of CONFIG_ENV_OFFSET
where the functionality has been introduced with
commit 5c088ee841f9 ("env_mmc: allow negative CONFIG_ENV_OFFSET").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Stefan Agner [Thu, 14 Jul 2016 00:14:37 +0000 (17:14 -0700)]
tools/env: complete environment device config early
Currently flash_read completes a crucial part of the environment
device configuration, the device type (mtd_type). This is rather
confusing as flash_io calls flash_read conditionally, and one might
think flash_write, which also makes use of mtd_type, gets called
before flash_read. But since flash_io is always called with O_RDONLY
first, this is not actually the case in reality.
However, it is much cleaner to complete and verify the config early
in parse_config. This also prepares the code for further extension.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Andreas Fenkart
Alexander Graf [Wed, 20 Jul 2016 23:31:56 +0000 (01:31 +0200)]
iso: Fix part info command
Partitions on the iso el torito partition table interpreter
only start from partition 1. So when printing out the tables,
let's also start counting at 1.
Ladislav Michl [Tue, 12 Jul 2016 18:28:32 +0000 (20:28 +0200)]
igep00x0: UBIize
Convert IGEP board to use UBI volumes for U-Boot, its environment and
kernel. With exception of first four sectors read by SoC boot
ROM whole (One)NAND is UBI managed.
Also merge NAND and OneNAND defconfigs as now one binary can serve
both flashes.
As code is too big now, drop CONFIG_SPL_EXT_SUPPORT to make it fit.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Ladislav Michl [Tue, 12 Jul 2016 18:28:26 +0000 (20:28 +0200)]
cmd: mtdparts: support runtime generated mtdparts
Some CPUs contains boot ROM code capable reading first few blocks
(where SPL resides) of NAND flash and executing it. It is wise to
create separate partition here for SPL. As block size depends on
NAND chip used, we could either use worst case (biggest) partition
size or base its size on actual block size. This patch adds support
for the latter option.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Tue, 12 Jul 2016 18:28:25 +0000 (20:28 +0200)]
cmd: mtdparts: use defaults by default
Boards which are defining default mtdparts often need them early
in boot process (to load environment from UBI volume, for example).
This is currently solved by adding mtdparts and mtdids variable
definitions also to default environment. With this change, default
partitions are used by default unless explicitely deleted or
redefined.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Tue, 12 Jul 2016 18:28:23 +0000 (20:28 +0200)]
cmd: mtdparts: fix null pointer dereference in parse_mtdparts
In case there is no mtdparts variable in relocated environment,
NULL is assigned to p, which is later fed to strncpy.
Also function parameter mtdparts is completely ignored, so use it
in case mtdparts variable is not found in environment. This
parameter is checked not to be NULL in caller.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Tue, 12 Jul 2016 18:28:22 +0000 (20:28 +0200)]
cmd: mtdparts: fix mtdparts variable presence confusion in mtdparts_init
A private buffer is used to read mtdparts variable from non-relocated
environment. A pointer to that buffer is returned unconditionally,
confusing later test for variable presence in the environment.
Fix it by returning NULL when getenv_f fails.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Tue, 12 Jul 2016 18:28:19 +0000 (20:28 +0200)]
mtd: OneNAND: add timeout to wait ready loops
Add timeout to onenand_wait ready loop as it hangs here indefinitely
when chip not present. Once there, do the same for onenand_bbt_wait
as well (note: recent Linux driver code does the same)
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Tue, 12 Jul 2016 18:28:15 +0000 (20:28 +0200)]
armv7: add reset timeout to identify_nand_chip
identify_nand_chip hangs forever in loop when NAND is not present.
As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout
to let function fail gracefully allowing caller to know NAND is
not present. On NAND equipped board, reset succeeds on first read,
so 1000 loops seems to be safe timeout.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
projects / u-boot / log